开云体育

Ah, good point. MTR2000...rx, tx, & gnd lines only. [email protected]> wrote:

You didn't mention the radio model, it makes a difference. Earlier RSS for earlier models suffered from timing loops to compensate for a lack of suitable data buffering back then but nearly all

if you need more i have about 200 pcs new in box , cr1070nm all made for comscope/? cell reach 7/8 to male type n all new in boxes?

I use Dosbox and windows 7, I also have a vmare win 3.11, win XP and win 2k.I have been able to read and write to just about any radio.I also use a "real' serial port card that has 2 port and a

Hello, I have recently got a Helper Instruments PS 250. Does anyone have a manual or schematic for the Helper Instruments PS 250. thanks 73's Brian w7fdd

Hi Folks. Has anyone used RSS in a virtual machine? I've got RSS 3.03.03, running in a 32bit WinXP under Oracle VirtualBox, inside Win10. I can read the station, it gets to 100% and then hangs,

That's not gonna cause problems at all...<eye roll>

146.6875 out / 146.0875 Actually,taking a closer look. 146.6875 / .0125 = 11735.0 146.0875 / .0125 = 11687.0 Are even integers, so a 12.5 KHz? (and 6.25 or 2.5 KHz) radio will do it. Still some

if you have line of site then a pair of these little cheap beauties will give buckets of bandwidth https://uk.store.ui.com/uk/en/category/all-wireless/products/litebeam-5ac we have wifi links from as

Adrian, If you have line of site or you can make a LOS shot a pair of Ubquiti 5GHz radios configured as an Ethernet bridge.? 500m should no problem.? I suggest 5GHz if it is available in your

Mike/Jeff OK. So the cable you want to put a connector on is ANULAR, as opposed to SPIRAL, is that correct? If so, I will change the 7/8" NF cutoff connector I was planning to send. BTW The Spiral

Anthony; I have done it with Hamvoip.? We are in the process of converting to ASL3, but I have not gotten this to work with that distro yet.

Good morning everyone and happy Saint Patty's day! Does anyone have a used fairly inexpensive UHF repeater that I can purchase for a back up system? Chad Nelson WI9HF/WRPL979 Janesville

Jeff, You are correct and I did not note that in Charle's offer/comments. It is not a spiral type cable. BTW Jeff..I'd still like to have some direct communication with you if at all possible. My

Use an external Yagi for the wifi...they work great ...use them all the time with BDAs...500mtrs should not be a problem with them...does your wifi router have external antenna connectors? Chris

Just to make sure we/you/all are on the same page, Mike’s cable is not helical (spiral) corrugation so it wouldn’t be Phelps-Dodge (FXCC series). --- Jeff WN3A From:

Do you have line of sight to the repeater? Matt AL0R Sent: Monday, March 17, 2025 07:50 To: [email protected] Subject: [repeater-builder] Internet provision at a remote repeater

Mike OK. I'll send you one. Regards, Charles F. Adams K3HKZ Industrial Communications Co. 121 N Sitgreaves Street Easton, PA 18042 Office 610-253-1214 Cell 610-360-0050 Fax 610-253-4504 Sent:

Charles, The address here is: * Miike Ryan * 4828 Commonwealth Road * Palmetto, FL 34221. Thank you very much! - Mike Sent: Monday, March 17, 2025 8:55 AM To:

Hi The 7/8" cable you have is probably Phelps Dodge with solid center and spiral outside. No soldering required. We have a few used (cut off) connectors laying around, which I would offer FREE if you