Re: Windows 7 config
He¡¯s using the radio for Winlink/VaraFM, not a repeater. Data, not voice. Sent: Tuesday, November 1, 2022 1:29 PM To: [email protected] Subject: Re: [repeater-builder] Windows 7 config I
By
Jeff DePolo WN3A
·
#195296
·
|
Re: Windows 7 config
I strongly disagree Scott... That's a recipe for disaster. Feeding wide band unsquelched noise to a modulator will cause the transmitter to over deviate. Remember the squelch noise out of a
By
Chris Boone WB5ITT
·
#195295
·
|
Re: Quintron Corporation / Glenayre 70cm pager transmitter & Power Supply. Need info.
Thanks Burt, probably wouldn't be too difficult to put in a PTT actuated relay. I remember the old SoCal days, Neil, and others. Was in Simu Valley ARC, and we had a 440 machine on Oat Mountain. I was
By
Frank Perkins
·
#195294
·
|
Re: Windows 7 config
Scott, It will depend on the radio used. For most Mot. radios with the 16 pin connector, you don't need to do anything special in programming. For the CDM series with the 20 pin option connector, you
By
Scott Zimmerman
·
#195293
·
|
Re: VHF MTR2000 Poor Receive Performance
The return loss of the first cavity seems off. At 0.4 dB IL I would expect the match to be around -30 dB as you saw with the other two cavities. Is that the cavity that seemed to be giving you
By
Jeff DePolo WN3A
·
#195292
·
|
Re: Quintron Corporation / Glenayre 70cm pager transmitter & Power Supply. Need info.
The boards look like those made by Aerotron. A definite blast from the past of the late 1970's version I used to maintain for hospitals in 160 mhz at multiple sites in NYC and CT. There were lots of
By
J Donovan
·
#195291
·
|
Re: Quintron Corporation / Glenayre 70cm pager transmitter & Power Supply. Need info.
Yes, this series (QT6700??) were bad about intermod even with a good band pass band reject on them. I ended up figuring it was mixing in the exciter. It could come in if there was any spot on the
By
Don Clark
·
#195290
·
|
Re: Connecting Yaesu DR2X Repeater to Raspberry Pi/Allstar?
Is anyone still making outboard CTCSS encode and/or decode boards? CommSpec?
By
Jim Barbour
·
#195289
·
|
Re: Connecting Yaesu DR2X Repeater to Raspberry Pi/Allstar?
Well, a year ago I codgered up substitution an Arduino Nano ($5) for the CTCSS encoder the DR2X requires if in the remote mode. I have the "script" you down load to the Aurduino and it outputs a PL
By
Larry Macionski
·
#195288
·
|
Re: Windows 7 config
I can't answer myself, but I know you will need to be more specific. What radio? What software?
By
Jim Barbour
·
#195287
·
|
Re: Quintron Corporation / Glenayre 70cm pager transmitter & Power Supply. Need info.
I may be wrong here, but I recall a lot of problems on Mt. Wilson, and other sites, to broadcast 940 MHz STL's as well as VHF radios from Quintron paging transmitters.? As I recall, it was when drive
By
Burt K6OQK
·
#195286
·
|
Windows 7 config
What do I need to do in the motorola programming software and Windows 7 to config the RIM-Maxtrac wit work with Winlink or Vara FM.
By
SCOTT READ - KM6RFB
·
#195285
·
|
CSI-32
Are there any CSI-32 controller folks on here??? I have the manual but the factory reset is not working. -- - Regards, Karl Shoemaker To contact me, please visit SRG's web site at
By
Karl Shoemaker
·
#195284
·
|
Quintron Corporation / Glenayre 70cm pager transmitter & Power Supply. Need info.
Hi folks, I have a 45w and a 90w 70cm transmitter and power supply and need manual or any info. See pics. Google showed install and setup manual for much later (Jan 93) VHF advanced version, but I
By
Frank Perkins
·
#195283
·
|
Re: VHF MTR2000 Poor Receive Performance
That's great news!
By
Bradley Andrews
·
#195282
·
|
Re: VHF MTR2000 Poor Receive Performance
By
Jared Smudde
·
#195281
·
|
Re: VHF MTR2000 Poor Receive Performance
Cavity 1: -23DB Return Loss at Pass Frequency, 0.4DB IL at Pass Frequency, -30DB IL/Notch at Reject Frequency Cavity 2 (middle cavity): -30DB Return Loss at Pass Frequency, 0.4DB IL at Pass Frequency,
By
Jared Smudde
·
#195280
·
|
Re: Connecting Yaesu DR2X Repeater to Raspberry Pi/Allstar?
"Best" is subjective. The problem with that solution currently is some of the required products are unavailable.? The SC-50 and CT-30 are discontinued because the encoder/decoder IC in no longer
By
Kevin Custer
·
#195279
·
|
Re: UHF Cans?
That would be great! Thanks Jeff. Tedd, VE3TJD
By
Tedd Doda
·
#195278
·
|
Re: UHF Cans?
Looks small enough to be UHF. I can verify when I get home tonight. --- Jeff WN3A -- This email has been checked for viruses by Avast antivirus software. www.avast.com
By
Jeff DePolo WN3A
·
#195277
·
|