开云体育

A "new" cable kit is a bit expensive and Mark at Northcomm has them for $389.00. They are easy to make using RG-142 and crimp connectors, either silver plated or tri-metal for low PIMD. The RG-142

Does anyone have a factory new old stock Cellwave 526-4-2 factory made oem harness set they want to sell? I'm looking for a set for this duplexer I got that someone converted to some kind of band

The DB4060/4062 series had five different loop assemblies. Depending on the bandsplit (there are three) and whether the loop is used for high-pass/low-reject versus low-pass/high-reject determines

OK. Why isn't it connected to the building? Are you saying the ground ring around the building is there only as a ground for the shack? If it isn't not bonded to the electrical service ground, that

And be prepared to tell it again each time Windows does an update.

I am seeking advice where the RF feedline grounding/lightning arrestor block should be mounted to. I'm working on a project where the ham station is in the mezzanine of a warehouse where the tower

I haven’t seen the loop but the can uses a T connector and capacitor so if it’s like the Sinclair style Q loop, it’s the same and just needs to be tuned - there is a notch on both sides of the

I use two 50 watt Garmin AT/UPS AT 220 MHz ACSSB amps which are combined in a home brew Wilkinson Combiner. These were purchased in 2013 for ~ 50 dollars total at a local swap meet, the amps are used

You often have to tell it specificly to use that card as it sees the usb device as another sound card. Butch Bussen WA0VJR butchb@... irlp 7135 allstar 56023 echolink 790800

It uses the internal one normally From: [email protected] <[email protected]> On Behalf Of Butch-tiny puppy via groups.io Sent: Friday, April 11, 2025 7:58 AM To:

You probably need to tell jaws what doundcard to use. Butch Bussen WA0VJR butchb@... irlp 7135 allstar 56023 echolink 790800

Hi, I hope someone can help me figure out an issue. I am trying to use a West Mountain Radio Rigblaster plug and play sound card interface to run echolink. The issue I am running into is that

Dan, I have a few of these types of amps. What switching transistor gets removed? also wanting to know more about your charts for this amp.

What would be required to change a DB4060 series can that is currently set up for pass low / block high to pass high / block low?? If loop replacement is required, where can they be

Wouldn't even risk that guy. I sent him a set of cans 4 years ago and he straight up disappeared after he told me to ship them to him. Tried every form of contact known to man and never got a

I've got a TB8100 in GMRS service.? I want to of course provide proper ID, but as I share the channel with another system, I do not want the ID to beacon, just politely properly ID routinely after

Is this them?? Duplexer Repair is a service division of Alabama Broadcast Services, LLC [6]. Duplexer Repair performs repairs, refurbishing, and tuning of a wide variety of duplexers and cavity

Kevin has given me a lot of help tuning the overpainted and unknown dB4060 diplexer.? It is smelling a lot like they are not the ham band model.? If anyone has up to date contact info on the firm

I agree.? They are false economy.? The only protection that they give the receiver from transmitter power is a very sharp notch.? Burn up the teflon, loose the notch tuning, and you have the chance

Regarding the height:? The cans are 8 inches in diameter, and they are 21" tall.? The stated height does not include the tuning rods and other projections. Regarding the range: I do not know what