开云体育

I have located a "new" spool of FSJ4-75, 2000', in SoCal. I have not personally inspected it, however, the pics I've seen show it still with the corrugated cover on the spool. It is stored upright and

VHF Engineering used a similar COR board .? ?While not hardware so to speak I would look at the ARDUINO repeater control software. Ralph ku4pt

On 2025-03-05 3:11 p.m., Ramesh Dhami \(VA3UV\) wrote: > On 2025-03-05 12:06 p.m., David Cameron - IRLP via groups.io wrote: >> I use a similar method that I find a little more accurate for

On 2025-03-05 12:06 p.m., David Cameron - IRLP via groups.io wrote: > I use a similar method that I find a little more accurate for setting > the loops. It's very hard to set the pass for 1db IL

For tail timer for repeater using 555 build as regular timer circuit with timing for like 3 sec or what you need and with transistor driven by COS ground pin 6 of 555 (transistor collector to pin 6,

Hamtronics was a US based company that designed and built repeater circuitry in modules and made it available in kit form or assembled and tested. Here are all of the manuals for this equipment

I did one years ago with a 555 driving a 4093 Schmidt trigger with a RC circuit to handle hang time...it's easy .. I don't have the schematic here with me right now but I can post it later Chris

I use a similar method that I find a little more accurate for setting the loops. It's very hard to set the pass for 1db IL accurately. I use this method to build VHF duplexer a from anywhere from 4 to

I will try that. When searching for some info about the topic it appeared me but I was in a hurry and did not let some time to know how it works. So that I asked here for a solution. Even that, I

+11dBm output is no stingy signal at 12.6 mW into 50 ohms. ? It's too bad these can't be directly FM modulated, because you could likely avoid the multiplier sections of a common crystal exciter /

I would venture pin assignments.? ?I have been avoiding using pin 4 as cor. Instead leave it blank tie pins 4 and 10 together and use as ignition sence. Than use pins 8 and 12 for cor. And pl

Here's something to consider: https://www.repeater-builder.com/projects/hang-timer.html Kevin

Hi everyone. I built myself a repeater with a pair of Kenwood radios, ESP32 based and fully functional (automated beacon, auto/manual mode, screen ...). Although repeater tail is implemented by

<-- Hi Peter; I'm? no expert - but, out of respect to my "tutors" Kevin (W3KKC) and Andrew (VE3GTU), I'll have a go and sharing some recent learning / experienc

Tyler, I want to second what Kevin says. Show it on a schematic and on the board the points you are using for discrimator and the modulator. Thanks! Andy Zorca [email protected]> wrote:

Ok I will need to call them and see if they can tell me how much that service is. I called them the other day and the agent said they didn’t have anything like this. Sent: Tuesday, March 4, 2025

This unit is Verizon Only

I am using an arcom rc210 so not sure what that autopatch is looking for. Ken are you able to pitch in? Chad Sent: Tuesday, March 4, 2025 6:41 PM To: [email protected] Subject: Re:

Do I need a Vorizon account? Or can this be unlocked to work with Spectrum? Sent: Tuesday, March 4, 2025 6:41 PM To: [email protected] Subject: Re: [repeater-builder] running autopatch

Thanks for all the advice.? I was able to extend the rods using stainless with mixed results: -on "duplexer A" I can only get about 30db of isolation per cavity, which from what I'm reading is not