开云体育

Hello Oristo; It is good to know this topic is being followed. I hope there are others more capable and perhaps more patient than I, and I welcome them to please chime in. It may expedite the pace of

Rune, I spent the day verifying unknown filters in my ham shack and documenting their performance using your new "Analysis" module (Tks !). I attached files earlier for typical high pass and low pass

is there any info on measuring the Q of a network and antenna? I set up an S21 test using the matched network and antenna on CH0 and a short coil on CH1, looking at the LOGMAG trace for CH1 I measured

I don’t think splitting into two will be sufficient. From what I understood from the group owner around a week ago, the number of subscribers was showing no signs of tailing off. I think we need to

I downloaded v1.1 of the Calibration Procedure and all is well until I get to Note 21. When I connect the two ports together, my Blue Line is at the very top of the chart and the readout fluctuates

Here’s a suggestion to mull over… Suppose a second nanoVNA group be initiated called “NanoVNA for Beginners”, or “New to NanoVNA” The benefits are subtle but would potentially decimate the

Kurt, You are correct. That is the very reason I used a wide-band device. I wanted to know the total power coming out of the port. I was not trying to determine the amount of signal that is being used

Rune, Here you go: ch> version 0.1.1.1-5-gd609fb2 ch> info Kernel: 4.0.0 Compiler: GCC 8.2.1 20181213 (release) [gcc-8-branch revision 267074] Architecture: ARMv6-M Core Variant: Cortex-M0 Port Info:

Hello David, I had heard rumours of there being bad Female-Female adaptors included with some NanoVNAs. I have a bunch of cheap chinese adaptors of that kind, the one that came with the NanoVNA, and

drkirkby@...> wrote: I forgot to say, the trace that’s barely visible is the thru on the left of the photograph. It’s return loss is very close to 0 dB even at 7 GHz. Dave -- Dr.

I’ve have two NanoVNAs, and both were supplied with a female-female SMA adapter like on the right. It quite a bit longer than most SMA female-female adapters. The one on the left is much shorter.

Hi David - You have reached a wrong number; I wrote only https://oristopo.github.io/nVhelp/html/Menu.htm You could request a firmware change on GitHub, e.g.: https://github.com/ttrftech/NanoVNA/issues

If you are changing menus, could you make the VNA back button loop around if using the switch. For example, if you are in a menu item labeled back, if you press left switch, it goes up one item, and

Do a search in this group for "Place To Buy".

I caught a YouTube video on these and I am very interesting in getting one for my shack however I know next to nothing about them. I have several antenna analyzers for my ham radio equipment and these

$15 Particle Xenon has bluetooth https://www.amazon.com/dp/B07N964T22

Hi Bryan, I'm not entirely sure *why* it happens - but I believe edy555 has fixed the issues in his latest firmware versions. I don't know about Hugen's firmware versions. The next version of

Hi Bryburn Using a wideband power meter (you did not specify what device you used) will not be able to filter out the harmonics signal amplitude. For that purpose you need a selective power meter or a

Rune, With all of the recent versions of nanoVNASaver (0.0.11, 0.0.12, 0.1.0, 0.1.1) I have been occasionally getting a pure white screen on the nanoVNA while making measurements using nanoVNASaver. I

Does anyone know a way to cleaner the 5 calibration memories? The DMR-CLEAR_MEMORY_DFU.dfu file does not seem to do this (only firmware cleaner?). Thanks