开云体育

Hi Paul, I sent LDG an email about 10 years ago asking if there was a factory reset for the AT-100 Pro-II - the reply was no. I have an AT 200 Pro that does have the factory reset, and I know the AT

I’m trying to debug a “can’t tune parts of 10m” issue and I want to collect some baseline data. Is there a way to factory reset the LDG AT-200PRO-II? The manual is silent on that issue. 73

Yes one has to preset the tuner at the beginning for bands and the antenna being used. After that, hands frr mostly. Joseph D. Yuna Joseph D. Yuna (LCDR USN/ret.) W4JDY / EM79xr / ITU 8 / CQ 5 United

My LDG AT-1000Pro II Autotuner just adjusts when I tune up the antenna or change frequency. Hands off with this beauty. Joseph D. Yuna Joseph D. Yuna (LCDR USN/ret.) W4JDY / EM79xr / ITU 8 / CQ 5

How is cable not needed?

Thanks to all who responded. Yes, it's a Packtenna 29' random wire with 9:1 unun with 25' coax into Z-11 "ANT" SO-239.? 1' jumper from "TX" SO-239 to 1:1 unun choke then 1' jumper into 7300 SO-239.

If in Auto Tuner mode, the cable is not needed. W4JDY Sent: Wednesday, January 8, 2025 10:54 AM To: [email protected] Subject: Re: [ldgelectronics] IC-7300 and Z-11 Pro II Do you have the

I had to press the tuner’s tune button until it learned the correct setting for the auto tuner function of the LDG to work. W4JDY Sent: Tuesday, January 7, 2025 11:39 PM To: [email protected]

Do you have the control cable for the tuner??? That cable controls the tuner from the ic7300 If you have the cable use tune button on the tuner? 73 Ron n9ee

I see an antenna issue, separate from the tuner, but it should help tuning when the Z-11 wakes up. With the 29' wire, you need a 9:1 unun between the feedline and the 29' wire.? I found 50' wire is a

Just got this ATU to pair with IC-7300, a random wire (currently 29') and the 1:1 unun. I'm struggling with the ATU a bit and was hoping someone with 7300 experience might be able to direct me. Per

Not sure quite what happened with mine. It worked fine on all bands except 30m, where it tuned ok with 10w but became unstable with higher power… I’ll contact LDG tomorrow, but I’ve already

Had the same happen to me a few years back, My fault op error, Ldg sent me 2 new ones free of charge to Sweden, still have one spare, very good customer service, Think the guy i delt with a was

If I change C5A thru C5E are there any other components that you guys would recommend changing based on experience? Ian LB6OJ

Thanks Ken. I have not tried the Z-100plus, but it looks like the Z-100A process is what it appeared to be and the tuner adjusts the radio's TX config through the IC-108 cable. 73 -Matt K1SP

Thanks Mike. I was hoping that was the case and that makes life a lot easier. 73 -Matt K1SP

How much power as the limit on 30 meters is 200 watt as I understand it. But my question is what kind of antenna? I have seen this often with End Fed Half Wave antennas as the toriod heats up and then

At least it’s a very easy fix!

Had a nasty experience with my LDG auto tuner. It’s been working fine for 2 years. Recently my amp has complained a few times about high SWR on 30m after tuning. It tunes ok, but after 10 seconds of

I see 2 threads on this. My z100A manual shows the 108 cable for 991A and 891. I just set it up again, with "tuner select" in amp, the 8 pin end of the cable into? "tun-lin" jack, the 3.5mm plug into