开云体育

A note to Yaesu support will give you your verification, either phone or email. https://www.yaesu.com/?cmd=ContactUs&DivisionID=65 73, Kent K9ZTV -- This email has been checked for viruses by AVG

Hi, I have been studying the AT1000 manual and this forum prior to a possible purchase and venture to suggest that the yaesu 8pin tuner ports do not seem to have the ”tx req” needed to allow

Thanks, Gregor for letting us know. I’ll check out the YouTube video as soon as I can and make the cable in my shop. I will also let our LDG friends know so they can clarify the uncertainty. They

The Y-ACC-2 cable is intended to go into the Linear port on the FXdx10, which is 10 pin. I would think using the same-named pins on the 8-pin tuner port would work, but I haven’t tried. ?If you can

Hi Jeff, I am setting up a new FTDX10. Tuner cables are unavailable/backordered, so I thought I would simply make my own. Ten pin DIN’s are also hard to find at decent prices. Just as I was ready to

Hello - it's me again... I went back through the Yaesu documentation and found that the tuner port is actually an 8-pin Mini-DIN on the FT-DX10. The documentation for the Y-ACC-2 cable shows a 10-pin

Ah ha! That was going to be my next question! I was looking around for the cable and it appears to be on back order everywhere I checked. I have a spare 8 pin connector and a TRS connector. Seems easy

Jeff, Yes, the Y-ACC-2 is the right cable according to the DXEngineering website which also states: "FTDX10 ??? Z-11ProII ??? Connects to transceiver TUNER port, enabled in menu: Operation,

Hello, I bit the bullet this past weekend and bought the FTDX10. I forgot to pick up the adapter cable for my Z11 Pro 2 tuner. I’ve been searching the message archive. I saw mention of the Y-ACC-2

I ended up using a flathead screw driver to lift the tabs on the plastic adapter on the LDG cable. Once I was able to disconnect it, I used a small set of diagonal cutters to trim out some of the

Carey; Got my terminology confused a bit there; sorry about that. I started out with a home-made Y-ACC-3 cable (from the online print), then purchased the Ameritron DB-DB15Y cable for the amp. I took

Steve, are you by any chance using the ARB-704 interface? I have an old AL-811 amp that I bought from a local guy who upgraded. I said the Y-ACC-3 uses the Cat control? DB9 in error, the pin out in

Here's the IC-108 cable spec from LDG.? This works with my 710 plug the 3/8 connector into Rem and plug the 8-pin din in tuner/amp.? Set the menu to use an external tuner instead of internal and set

Carey; I have exactly the same setup, with an AT600ProII, and FTdx3000, and an amplifier. The Y-ACC-3 will do exactly what it says it will do; drive a radio tune cycle (CW, key-down, 5 watts output)

I'm curious and a little confused about which cable is correct to run the AT600Pro on My FTDX 3000. I bought this tuner to go with an amp and without the amp it's not needed, the internal tuner

Do you know if the ic-108 cable will work with the Z11-Pro II and the FT-710 AESS ? Thanks, Dale N3JUO

I don't think the tuner is finding good settings in full auto. Manual says that for a full tune SWR must be over whatever is set. My tuner will not go lower than 1.7, yet 1.1 SWR is on the scale. How

Thank you for the info. In full auto mode I am releasing the tune button and getting great results. Just worked Canada, Scotland, and Northern Ireland. Paul KG5TBT wrote:

Hi Wyatt. Many thanks for you comprehensive reply. I will try and find a stock in the U.K. All the best. 73's

Same here Dave. Some hints from fellow hints you may find here /g/ldgelectronics/topic/95909285#916 ( /g/ldgelectronics/topic/95909285#916 ) Nothing helped for me so