Keyboard Shortcuts
ctrl + shift + ? :
Show all keyboard shortcuts
ctrl + g :
Navigate to a group
ctrl + shift + f :
Find
ctrl + / :
Quick actions
esc to dismiss
Likes
- Ldgelectronics
- Messages
Search
|
Re: LDG AT-100Pro2 to FT-710 Interface Cable
开云体育the package from ldg that the cable comes in, shows that acc-1 is
for the 710. I did tell hro of the descrepency and they kindly
replaced the acc-2 with the acc-1 at no charge for me. On 3/16/2024 1:56 PM, Jeff - KC1TEM
wrote:
|
|
Re: LDG AT-100Pro2 to FT-710 Interface Cable
Thanks. My confusion came from a chart on the HRO website that indicated that the ACC-2 cable was the one to use with FT-710 On Fri, Mar 15, 2024 at 17:04 N5KBP via <martyduplissey=[email protected]> wrote: I use the ACC-1 with my FT710 and the AT1000PRO2. Works well. I don't believe the ACC-2 will work with the FT-710. |
|
Re: ldg at100 Pro ll
Ok great information, I am waiting on them to?get back to me, as I have a at-1000pro 2 that doesn't work on the meter/pc TTL port, as they now sell them with it switched off, in firmware, I hope that they will send me the firmware that has not been disabled, as I have a interface for my Kenwood TS 2000 that uses this port to set the tuner, Dave On Sat, 16 Mar 2024, 15:28 David Bradley, <bozzbradley@...> wrote:
|
|
Re: ldg at100 Pro ll
I did contact LDG ,quick reply they said that the firmware hadn't any issues since its release? but if I have any problems, to reach out to them ,brilliant support,Dave 2E0DTB 73? On Fri, 15 Mar 2024, 12:01 davebb123456, <davidbrowne76@...> wrote:
|
|
Re: LDG AT-100Pro2 to FT-710 Interface Cable
开云体育according to the package that the acc-2 came in, you should use the acc-1 for the 710 Phil On 3/14/2024 5:10 PM, Jeff - KC1TEM
wrote:
Does the mean the Y-ACC-2 cable does not work with the FT-710?? HRO's website has a link to a chart on the AT-200Pro II page that says it's the right cable, but in the store they have a chart from LDG that says the Y-ACC-1 cable is the right one.? Which is right? |
|
Re: RC-100/RT100 Question
I posted this as a reply to a mental mish mash of the unun post and this one.? I have cleaned it up as to this post, and re-posted here.
As previously pointed out, the choice of ratio depends on the antenna impedance relative to the tuning range of the tuner.? The best approach is to measure the impedance at the feed point of the open wire line with an antenna analyzer or NanoVNA.? I have used an MFJ analyzer for years but now have and prefer the NanoVNA.? Good NanoVNAs are available inexpensively. I got mine from DX Engineering. If you get one you can measure the antenna at the open wire feed point. The actual impedances measured will inform as to what transform impedance is appropriate. I used a 1:1 on my 25’ OCF flagpole antenna. It tunes well from 40-6 meters and will tune 80 but I suspect the overall efficiency is pretty low. For you, with the RT-100 in line the ratio may not matter much as long as it is connected between the open wire line and the coax. |
|
Re: ldg at100 Pro ll
Hi no worries, Dave 2E0DMB? On Fri, 15 Mar 2024, 11:51 David Bradley, <bozzbradley@...> wrote:
|
|
Re: ldg at100 Pro ll
Wow thanks Dave ,for info much appreciated ,Dave 73 2E0DTB D T Bradley On Fri, 15 Mar 2024 at 11:21, davebb123456 <davidbrowne76@...> wrote:
|
|
Re: ldg at100 Pro ll
Hi David Yes it can, Open up your tuner and write down the number on the label on the? IC and go on there website and fill out?the form, Dave 2E0DMB? On Fri, 15 Mar 2024, 08:35 David Bradley, <bozzbradley@...> wrote: Can my above tuners firmware be updated,I wasn't aware that ldg tuners could be updated ,Dave 2E0DTB 73 just curious,TIA |
|
Re: LDG AT-100Pro2 to FT-710 Interface Cable
Does the mean the Y-ACC-2 cable does not work with the FT-710?? HRO's website has a link to a chart on the AT-200Pro II page that says it's the right cable, but in the store they have a chart from LDG that says the Y-ACC-1 cable is the right one.? Which is right?
|
|
Re: Can I power via a distribution block connected to my switching power supply
Terry Malin
开云体育Using the same Power Supply with a fused distribution block!Terry On 3/13/2024 5:28 AM, Nate W4NDK wrote:
Can I power my AT-600PROII via the supplied power cable to power pole adapters and a distribution block that connects to my switching power supply by Samlexpower (SEC-1235M) that also powers my transceiver? |
|
Re: Can I power via a distribution block connected to my switching power supply
开云体育In short, yes. I have a distribution block distributing power from my ICOM switching power supply to my RC/RT-600, my RIGblaster audio interface and my ct-17 serial to CI-V driver.?Al K5TAN On Mar 13, 2024, at 5:51 PM, Nate W4NDK <conchd@...> wrote:
|
Ryan - N7WAA - 3143494 - WREL204 - 2NA283
to navigate to use esc to dismiss