Hi every one, ?
I need advice on bat cars. ?My 380 S2 has, like most a “Z Spar” main mast and bat cars system with balls.
I am having trouble with my head car getting stuck. The balls are in good condition but the car jams and will not move. ? I believe some cars have been updated with slides instead of ball, has anyone got any experience on this subject? ?Thanks?
|
You can order Lagoon parts from MultiTech Marine in Fort Lauderdale. MultiTech is also dealers for Quick (water heaters & windlass) and Incidence Sails. ?And I believe MultiTech now has a location in Annapolis.? But for hardware, plumbing & ?most electrical, you can go to any marine chandlery for spare/replacement parts (West Marine, Defender, etc).? For Yanmar parts, go to a Yanmar dealer or Bay Shore Marine in Annapolis has on-line ordering and lots of engine parts in stock.? You can get Zincs from boatzinc.com.? ? Frankly, I’m finding Amazon has more and more stuff which tends to be cheaper and much faster shipping for Prime members. ? Doug ? ? ? Doug Jackson 1262 Crooked Tree Ct Westerville, OH? 43081 614-519-6996 doug@... Wishing you fair winds and following seas L421 ?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]> On Behalf Of Glen Coombs Sent: Monday, August 24, 2020 10:02 AM To: [email protected]Subject: Re: [lagooncatowners] L 42 parts list ? I've ordered lots of Lagoon parts from Groupe-Beneteau in Marion, SC.? Phone: 843-629-5320.? Unfortunately, I heard they are closing by the end of the year so I don't know how we'll get parts in the U.S. after that. Soon to be in Punta Gorda, FL
Looking for source for parts for Lagoon 42 2017 build hull 142
want order replacement spare parts on rigging and utility’s such as fresh water pumps.
Sunny Skye L42 hull 142
|
The factory put a screw on the inside on our's (hull #434) and the gelcoat cracks were there before we added the padeyes for the spinnaker. 
|
I've ordered lots of Lagoon parts from Groupe-Beneteau in Marion, SC.? Phone: 843-629-5320.? Unfortunately, I heard they are closing by the end of the year so I don't know how we'll get parts in the U.S. after that.
Glen
Dream Seeker, L380 #634
Soon to be in Punta Gorda, FL
toggle quoted message
Show quoted text
Looking for source for parts for Lagoon 42 2017 build hull 142
want order replacement spare parts on rigging and utility’s such as fresh water pumps.
Sunny Skye L42 hull 142
|
Looking for source for parts for Lagoon 42 2017 build hull 142
want order replacement spare parts on rigging and utility’s such as fresh water pumps.
Sunny Skye L42 hull 142
|
?Three screws hold factory installed spi block on the bow on my L 400. Noticed that my bow screw has some gelcoat cracks so thinking to reinforce by adding 3 more screws. Anyone has done that before, or has better idea? 
|
Ancor holder measurements Lagoon380S2 Hull 583 build 2009
Hi all,
my anchor holder flew away during an anchorage at 45 Kts.?
I had an anchor holder mounted with rivets and not welded - unfortunately, see enclosed pic please.
Do someone has this anchor holder an can give me the measurements or maybe a replacement??
Thanks in advance!
Ahoy Ole
|
We are putting our L400 up for sale.? Current location NE Florida.?? She is a 2013 4 cabin - 3 head.? lots of updates completed.? Asking 270k before? I get a broker.? Want pictures and list of updates, send me a private message.
Thank you and have a great day
Marcus
|
Re: Best option for new roller furling jib
Hi Jeff, I presently have a facnor unit. Do I have to replace the headstay if I switch to Pro-Furl?
Thanks, Joe
?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]>
On Behalf Of Jeff RUSSELL via groups.io
Sent: Tuesday, August 4, 2020 12:09 PM
To: [email protected]
Subject: Re: [lagooncatowners] Best option for new roller furling jib
?
The Profurl C-430 is their newer Coastal model and it's a little larger letting you use 1/2" wire size.? The NCi4216D only go up to 3/8 wire size so if that is not what you
have then the LC42D is an older version from Profurl same as the NCi at a much better cost.? The list price on the C-430 is $3900.00? LC42D is $2800.00
|
Re: Fresh water appearing above nav station
Here is an update, somewhat delayed? due to lack of rain, and then Hurricane Isaias came through! I wrapped the seam of of the bimini support with electrical tape, and that did the trick. No more water. Hard to believe that so much entered through that seam. Thanks to all who replied. Now I can move onto my next boat conundrum...
|
Re: Drilling the Plexiglas Windows
Oops, the info was further down in my Email.
8O)
Steve
toggle quoted message
Show quoted text
-----Original Message----- From: [email protected] < [email protected]> On Behalf Of Steve Kritenbrink Sent: Tuesday, August 4, 2020 4:47 PM To: [email protected]Subject: Re: [lagooncatowners] Drilling the Plexiglas Windows Use Snads from Sail Rite. Part#103652. They have an adhesive backing and Sail Rite also sells an activator to strengthen the adhesive. On of 193 in their catalog. Or look on line. I wound not drill a hole into the plexiglass. Steve K
|
Re: Drilling the Plexiglas Windows
Use Snads from Sail Rite. Part#103652. They have an adhesive backing and Sail Rite also sells an activator to strengthen the adhesive. On of 193 in their catalog. Or look on line. I wound not drill a hole into the plexiglass.
Steve K
|
Re: Drilling the Plexiglas Windows
Yes. please practice before committing to making a hole.?
On August 4, 2020 at 7:25 AM Steve Dolan <sdolan@...> wrote:
Thanks Kevin,
I’ll practice on a piece of scrap first to see what happens. It sounds like the slower the better though to minimize heat.
?
Steve in Solomons MD
410 S2E
?
?
Yes, not easy. It digs in too fast and will either break the drill bit or the acryllic. I have tried running it backwards to heat it up then slowly forward to pull out the "softened" plastic with some success. But go slowly. Keep going backwards alittle then forwards alittle until the hole it made then backwards to soften the plastic for a few seconds. I have heard the same with cutting acryllic with ply wood blade running backwards on a table saw. It does make a mess though. Now, I just use the laminate trimmer. It also makes a mess.??
On August 3, 2020 at 2:46 PM Steve Dolan <sdolan@...> wrote:
Has anyone had any experience drilling into the Saloon windows? I want to install shade screens on the outside. I know there is a special bit for drilling a hole (about 1/8”) but was wondering if anyone else has done it. ?I plan on tapping the hole and installing small bolts. This is a 2004 410.
?
Thanks for any help,
?
Steve in Solomons MD
410 S2E
?
?
?
?
|
Re: Best option for new roller furling jib
The Profurl C-430 is their newer Coastal model and it's a little larger letting you use 1/2" wire size.? The NCi4216D only go up to 3/8 wire size so if that is not what you have then the LC42D is an older version from Profurl same as the NCi at a much better cost.? The list price on the C-430 is $3900.00? LC42D is $2800.00
Hope that helps
Jeff Russell S/V Vitesse Lagoon 55S Mack Sails Inc.
|
Re: Drilling the Plexiglas Windows
Thanks Kevin, I’ll practice on a piece of scrap first to see what happens. It sounds like the slower the better though to minimize heat. ? Steve in Solomons MD 410 S2E ?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]> On Behalf Of Kevin Darden Sent: Monday, August 3, 2020 6:23 PM To: [email protected]Subject: Re: [lagooncatowners] Drilling the Plexiglas Windows ? Yes, not easy. It digs in too fast and will either break the drill bit or the acryllic. I have tried running it backwards to heat it up then slowly forward to pull out the "softened" plastic with some success. But go slowly. Keep going backwards alittle then forwards alittle until the hole it made then backwards to soften the plastic for a few seconds. I have heard the same with cutting acryllic with ply wood blade running backwards on a table saw. It does make a mess though. Now, I just use the laminate trimmer. It also makes a mess.?? On August 3, 2020 at 2:46 PM Steve Dolan <sdolan@...> wrote: Has anyone had any experience drilling into the Saloon windows? I want to install shade screens on the outside. I know there is a special bit for drilling a hole (about 1/8”) but was wondering if anyone else has done it. ?I plan on tapping the hole and installing small bolts. This is a 2004 410. ? Thanks for any help, ? Steve in Solomons MD 410 S2E
?
?
|
Re: Drilling the Plexiglas Windows
Yes, not easy. It digs in too fast and will either break the drill bit or the acryllic. I have tried running it backwards to heat it up then slowly forward to pull out the "softened" plastic with some success. But go slowly. Keep going backwards alittle then forwards alittle until the hole it made then backwards to soften the plastic for a few seconds. I have heard the same with cutting acryllic with ply wood blade running backwards on a table saw. It does make a mess though. Now, I just use the laminate trimmer. It also makes a mess.??
On August 3, 2020 at 2:46 PM Steve Dolan <sdolan@...> wrote:
Has anyone had any experience drilling into the Saloon windows? I want to install shade screens on the outside. I know there is a special bit for drilling a hole (about 1/8”) but was wondering if anyone else has done it. ?I plan on tapping the hole and installing small bolts. This is a 2004 410.
?
Thanks for any help,
?
Steve in Solomons MD
410 S2E
?
?
|
Drilling the Plexiglas Windows
Has anyone had any experience drilling into the Saloon windows? I want to install shade screens on the outside. I know there is a special bit for drilling a hole (about 1/8”) but was wondering if anyone else has done it. ?I plan on tapping the hole and installing small bolts. This is a 2004 410. ? Thanks for any help, ? Steve in Solomons MD 410 S2E
|
Re: Best option for new roller furling jib
Hi Jeff, thx for responding. What is the difference between the one above and the pro-furl 430?
Thx, Joe
?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]>
On Behalf Of Jeff RUSSELL via groups.io
Sent: Monday, August 3, 2020 2:33 PM
To: [email protected]
Subject: Re: [lagooncatowners] Best option for new roller furling jib
?
The Profurl NCi4216D would fit your standing rigging and we have sold many for replacements on that size Cats.? $2600 plus shipping from Stuart Florida.
The Harken, Furlex, Schaefer and Bamar systems we sell are much higher in price.
|
Re: Best option for new roller furling jib
The Profurl NCi4216D would fit your standing rigging and we have sold many for replacements on that size Cats.? $2600 plus shipping from Stuart Florida. The Harken, Furlex, Schaefer and Bamar systems we sell are much higher in price.
Hope that helps
Jeff Russell Ft. Pierce, FL S/V Vitesse Lagoon 55S Mack Sails Inc 800-428-1384
|
Best option for new roller furling jib
Hi all, I need a new furling drum, new or repaired aluminum extrusion. My furler is 15 years old. I'm thinking a new furler is my best bet. Which furler manufacturer and model would be the best bet for my L440?
Thanks in advance,
Joe
Sea Of Love
L440 BVI
|
SunnySkye
Ole
