开云体育

Starting with a freestanding track?

Axel Rau All Messages By This Member #23322 I have a linear arrangement (240mm long) for replicated circuits of the hierarchical daughter sheet. I want to draw 4 freestanding tracks (2 power and 2 signal) along the long edge and connect the replicated circuits with them. Usually I start a track at a pad, but how can I do it without a pad? I tried with free-standing vias, but had no luck. Axel --- PGP-Key: CDE74120 ? computing @ chaos claudius
CW All Messages By This Member #23323 First you should create a schematic representing the circuit you want to build a PCB board for. Have you done that? Chris -- toggle quoted message Show quoted text On 7/1/2022 4:13 PM, Axel Rau wrote: I have a linear arrangement (240mm long) for replicated circuits of the hierarchical daughter sheet. I want to draw 4 freestanding tracks (2 power and 2 signal) along the long edge and connect the replicated circuits with them. Usually I start a track at a pad, but how can I do it without a pad? I tried with free-standing vias, but had no luck. Axel --- PGP-Key: CDE74120 ? computing @ chaos claudius
Craig Burden All Messages By This Member #23324 You can draw a track and then just select it and change the net through the properties menu toggle quoted message Show quoted text On Fri, 01 Jul 2022, 16:13 Axel Rau, <Axel.Rau@...> wrote: I have a linear arrangement (240mm long) for replicated circuits of the hierarchical daughter sheet. I want to draw 4 freestanding tracks (2 power and 2 signal) along the long edge and connect the replicated circuits with them. Usually I start a track at a pad, but how can I do it without a pad? I tried with free-standing vias, but had no luck. Axel --- PGP-Key: CDE74120? ?? computing @ chaos claudius
Axel Rau All Messages By This Member #23325 开云体育 Am 01.07.2022 um 17:22 schrieb Chris via <chris.carter.iee@...>: First you should create a schematic representing the circuit you want to build a PCB board for. Have you done that? Yes, a flat hierarchy. Axel --- PGP-Key:?CDE74120 ?? ?computing @ chaos claudius
Tony Casey All Messages By This Member #23326 On Fri, 2022-07-01 at 17:13 +0200, Axel Rau wrote: I have a linear arrangement (240mm long) for replicated circuits of the hierarchical daughter sheet. I want to draw 4 freestanding tracks (2 power and 2 signal) along the long edge and connect the replicated circuits with them. Usually I start a track at a pad, but how can I do it without a pad? I tried with free-standing vias, but had no luck. Axel --- PGP-Key: CDE74120? ?? computing @ chaos claudius You can start an unconnected track (i.e. no associated net, or no netlist) in the middle of nowhere, but you may not be able to connect it to anything. It depends on your router settings. If you want to be able to connect anything to anything (at least initially): Route > Interactive router Settings... Mode: Highlight Collisions Options: Allow DRC violations. (You might also want to uncheck "Remove redundant tracks") (You obviously shouldn't "Allow DRC Violations" normally, or at least without good reason.) -- Regards, Tony
Axel Rau All Messages By This Member #23327 开云体育 Works perfectly! Thanks, Axel Am 01.07.2022 um 18:20 schrieb Craig Burden <craigburdenmsc@...>: You can draw a track and then just select it and change the net through the properties menu On Fri, 01 Jul 2022, 16:13 Axel Rau, <Axel.Rau@...> wrote: I have a linear arrangement (240mm long) for replicated circuits of the hierarchical daughter sheet. I want to draw 4 freestanding tracks (2 power and 2 signal) along the long edge and connect the replicated circuits with them. Usually I start a track at a pad, but how can I do it without a pad? I tried with free-standing vias, but had no luck. Axel --- PGP-Key: CDE74120? ?? computing @ chaos claudius --- PGP-Key:?CDE74120 ?? ?computing @ chaos claudius

Previous Topic Next Topic