i have my layout connected to computer running jmri 4.12. a layout panel using sml signals.
sections are defined.transits are defined. dispatcher settings are set to run train automatically.
enter a train name, dcc address etc.
click on add train
the active train window lists the train. status=running / mode=automatic / allocated section is the next section from the one train starts in
requested allocation waiting for dipatch window shows train and lists the next section after the one allocated
allocated sections shows the train in iy12 as occupied and shows iy13 as unoccupied

everything looks good except the train is not running

how do i get it to start. ?looks like the program assumed it running but it never moved

in the settings when i entered its dcc address of 5512 it shows as 5,512

if i run the train with a physical throttle the allocated sections table lists the sections in and the next one changing each as the engine moves.

how do i get the train to physically run automatically


tony

ps: if i use the autotrain window to switch to manual and use the speed lever to move the train it doesnt respond either

what am i doing wrong

tony

On Jul 15, 2018, at 12:18 AM, AD <bklyns_baseball_club@...> wrote:

i have my layout connected to computer running jmri 4.12. a layout panel using sml signals.
sections are defined.transits are defined. dispatcher settings are set to run train automatically.
enter a train name, dcc address etc.
click on add train
the active train window lists the train. status=running / mode=automatic / allocated section is the next section from the one train starts in
requested allocation waiting for dipatch window shows train and lists the next section after the one allocated
allocated sections shows the train in iy12 as occupied and shows iy13 as unoccupied

everything looks good except the train is not running

how do i get it to start. ?looks like the program assumed it running but it never moved

in the settings when i entered its dcc address of 5512 it shows as 5,512

if i run the train with a physical throttle the allocated sections table lists the sections in and the next one changing each as the engine moves.

how do i get the train to physically run automatically


tony

please ignore these 2 emails, my perferences were not all set to loconet.

train running but pauses randomly during the loop

any reason for that

tony

On Jul 15, 2018, at 12:26 AM, AD <bklyns_baseball_club@...> wrote:

ps: if i use the autotrain window to switch to manual and use the speed lever to move the train it doesnt respond either

what am i doing wrong

tony

On Jul 15, 2018, at 12:18 AM, AD <bklyns_baseball_club@...> wrote:

i have my layout connected to computer running jmri 4.12. a layout panel using sml signals.
sections are defined.transits are defined. dispatcher settings are set to run train automatically.
enter a train name, dcc address etc.
click on add train
the active train window lists the train. status=running / mode=automatic / allocated section is the next section from the one train starts in
requested allocation waiting for dipatch window shows train and lists the next section after the one allocated
allocated sections shows the train in iy12 as occupied and shows iy13 as unoccupied

everything looks good except the train is not running

how do i get it to start. ?looks like the program assumed it running but it never moved

in the settings when i entered its dcc address of 5512 it shows as 5,512

if i run the train with a physical throttle the allocated sections table lists the sections in and the next one changing each as the engine moves.

how do i get the train to physically run automatically


tony

please help as i am having a new issues with an engine running on
automatic mode

run a auto train
sometimes it makes it thru a loop. my throttle shows its speed
then randomly it stops and the throttle shows 0 speed
i switch to manual mode and use speed lever above 0 and it goes only to
stop again. speed lever went to 0
so i switch to auto and it goes.

i terminate train
i cant control the engine with my physical throttle
i write all sheets on the programming track
now throttle control e.ngine

please tell me what i am doing wrong or whats going on

tony

On Jul 15, 2018, at 1:00 AM, AD <bklyns_baseball_club@...> wrote:

please ignore these 2 emails, my perferences were not all set to

loconet.

train running but pauses randomly during the loop

any reason for that

tony

On Jul 15, 2018, at 12:26 AM, AD <bklyns_baseball_club@...>

wrote:

ps: if i use the autotrain window to switch to manual and use the

speed lever to move the train it doesnt respond either

what am i doing wrong

tony

On Jul 15, 2018, at 12:18 AM, AD <bklyns_baseball_club@...>

wrote:

i have my layout connected to computer running jmri 4.12. a layout

panel using sml signals.

sections are defined.transits are defined. dispatcher settings are

set to run train automatically.

enter a train name, dcc address etc.
click on add train
the active train window lists the train. status=running /

mode=automatic / allocated section is the next section from the one
train starts in

requested allocation waiting for dipatch window shows train and

lists the next section after the one allocated

allocated sections shows the train in iy12 as occupied and shows

iy13 as unoccupied

everything looks good except the train is not running

how do i get it to start. looks like the program assumed it

running but it never moved

in the settings when i entered its dcc address of 5512 it shows as

5,512

if i run the train with a physical throttle the allocated sections

table lists the sections in and the next one changing each as the
engine moves.

how do i get the train to physically run automatically


tony

On Jul 15, 2018, at 7:10 AM, Steve_G <RailRodder@...> wrote:

Hi Tony
Ensure that the autotrain loco has been fully released from all other throttles before attempting to create the train. Autotrain will not work on a shared throttle. You can clear all command station slots with an OpSw, see the digitrax documention for which one.
LocoNet slot monitor can be a good start to finding inuse throttles.
Steve G.

On July 15, 2018 1:59:00 AM EDT, AD <bklyns_baseball_club@...> wrote:
please help as i am having a new issues with an engine running on
automatic mode

run a auto train
sometimes it makes it thru a loop. my throttle shows its speed
then randomly it stops and the throttle shows 0 speed
i switch to manual mode and use speed lever above 0 and it goes only to
stop again. speed lever went to 0
so i switch to auto and it goes.

i terminate train
i cant control the engine with my physical throttle
i write all sheets on the programming track
now throttle control e.ngine

please tell me what i am doing wrong or whats going on

tony

On Jul 15, 2018, at 1:00 AM, AD <bklyns_baseball_club@...> wrote:

please ignore these 2 emails, my perferences were not all set to

loconet.

train running but pauses randomly during the loop

any reason for that

tony

On Jul 15, 2018, at 12:26 AM, AD <bklyns_baseball_club@...>

wrote:

ps: if i use the autotrain window to switch to manual and use the

speed lever to move the train it doesnt respond either

what am i doing wrong

tony

On Jul 15, 2018, at 12:18 AM, AD <bklyns_baseball_club@...>

wrote:

i have my layout connected to computer running jmri 4.12. a layout

panel using sml signals.

sections are defined.transits are defined. dispatcher settings are

set to run train automatically.

enter a train name, dcc address etc.
click on add train
the active train window lists the train. status=running /

mode=automatic / allocated section is the next section from the one
train starts in

requested allocation waiting for dipatch window shows train and

lists the next section after the one allocated

allocated sections shows the train in iy12 as occupied and shows

iy13 as unoccupied

everything looks good except the train is not running

how do i get it to start. looks like the program assumed it

running but it never moved

in the settings when i entered its dcc address of 5512 it shows as

5,512

if i run the train with a physical throttle the allocated sections

table lists the sections in and the next one changing each as the
engine moves.

how do i get the train to physically run automatically


tony

--
Sent from my Android device with K-9 Mail. Please excuse my brevity.

On Jul 15, 2018, at 2:33 PM, AD <bklyns_baseball_club@...> wrote:

so i cant have an engine in auto train and on my physical throttle at the same time.
will disconnecting the physical throttle be ok or must i use the opsw

tony

On Jul 15, 2018, at 7:10 AM, Steve_G <RailRodder@...> wrote:

Hi Tony
Ensure that the autotrain loco has been fully released from all other throttles before attempting to create the train. Autotrain will not work on a shared throttle. You can clear all command station slots with an OpSw, see the digitrax documention for which one.
LocoNet slot monitor can be a good start to finding inuse throttles.
Steve G.

On July 15, 2018 1:59:00 AM EDT, AD <bklyns_baseball_club@...> wrote:
please help as i am having a new issues with an engine running on
automatic mode

run a auto train
sometimes it makes it thru a loop. my throttle shows its speed
then randomly it stops and the throttle shows 0 speed
i switch to manual mode and use speed lever above 0 and it goes only to
stop again. speed lever went to 0
so i switch to auto and it goes.

i terminate train
i cant control the engine with my physical throttle
i write all sheets on the programming track
now throttle control e.ngine

please tell me what i am doing wrong or whats going on

tony

On Jul 15, 2018, at 1:00 AM, AD <bklyns_baseball_club@...> wrote:

please ignore these 2 emails, my perferences were not all set to

loconet.

train running but pauses randomly during the loop

any reason for that

tony

On Jul 15, 2018, at 12:26 AM, AD <bklyns_baseball_club@...>

wrote:

ps: if i use the autotrain window to switch to manual and use the

speed lever to move the train it doesnt respond either

what am i doing wrong

tony

On Jul 15, 2018, at 12:18 AM, AD <bklyns_baseball_club@...>

wrote:

i have my layout connected to computer running jmri 4.12. a layout

panel using sml signals.

sections are defined.transits are defined. dispatcher settings are

set to run train automatically.

enter a train name, dcc address etc.
click on add train
the active train window lists the train. status=running /

mode=automatic / allocated section is the next section from the one
train starts in

requested allocation waiting for dipatch window shows train and

lists the next section after the one allocated

allocated sections shows the train in iy12 as occupied and shows

iy13 as unoccupied

everything looks good except the train is not running

how do i get it to start. looks like the program assumed it

running but it never moved

in the settings when i entered its dcc address of 5512 it shows as

5,512

if i run the train with a physical throttle the allocated sections

table lists the sections in and the next one changing each as the
engine moves.

how do i get the train to physically run automatically


tony

--
Sent from my Android device with K-9 Mail. Please excuse my brevity.

On Jul 15, 2018, at 2:51 PM, AD <bklyns_baseball_club@...> wrote:

i cant find such an opsw
will filling the physical throttle with other addresses do the job
must it be removed from the wifi list of addresses but not bein used on one of the 4 throttles

tony

On Jul 15, 2018, at 2:33 PM, AD <bklyns_baseball_club@...> wrote:

so i cant have an engine in auto train and on my physical throttle at the same time.
will disconnecting the physical throttle be ok or must i use the opsw

tony

On Jul 15, 2018, at 7:10 AM, Steve_G <RailRodder@...> wrote:

Hi Tony
Ensure that the autotrain loco has been fully released from all other throttles before attempting to create the train. Autotrain will not work on a shared throttle. You can clear all command station slots with an OpSw, see the digitrax documention for which one.
LocoNet slot monitor can be a good start to finding inuse throttles.
Steve G.

On July 15, 2018 1:59:00 AM EDT, AD <bklyns_baseball_club@...> wrote:
please help as i am having a new issues with an engine running on
automatic mode

run a auto train
sometimes it makes it thru a loop. my throttle shows its speed
then randomly it stops and the throttle shows 0 speed
i switch to manual mode and use speed lever above 0 and it goes only to
stop again. speed lever went to 0
so i switch to auto and it goes.

i terminate train
i cant control the engine with my physical throttle
i write all sheets on the programming track
now throttle control e.ngine

please tell me what i am doing wrong or whats going on

tony

On Jul 15, 2018, at 1:00 AM, AD <bklyns_baseball_club@...> wrote:

please ignore these 2 emails, my perferences were not all set to

loconet.

train running but pauses randomly during the loop

any reason for that

tony

On Jul 15, 2018, at 12:26 AM, AD <bklyns_baseball_club@...>

wrote:

ps: if i use the autotrain window to switch to manual and use the

speed lever to move the train it doesnt respond either

what am i doing wrong

tony

On Jul 15, 2018, at 12:18 AM, AD <bklyns_baseball_club@...>

wrote:

i have my layout connected to computer running jmri 4.12. a layout

panel using sml signals.

sections are defined.transits are defined. dispatcher settings are

set to run train automatically.

enter a train name, dcc address etc.
click on add train
the active train window lists the train. status=running /

mode=automatic / allocated section is the next section from the one
train starts in

requested allocation waiting for dipatch window shows train and

lists the next section after the one allocated

allocated sections shows the train in iy12 as occupied and shows

iy13 as unoccupied

everything looks good except the train is not running

how do i get it to start. looks like the program assumed it

running but it never moved

in the settings when i entered its dcc address of 5512 it shows as

5,512

if i run the train with a physical throttle the allocated sections

table lists the sections in and the next one changing each as the
engine moves.

how do i get the train to physically run automatically


tony

--
Sent from my Android device with K-9 Mail. Please excuse my brevity.

so i cant have an engine in auto train and on my physical throttle at
the same time.
will disconnecting the physical throttle be ok or must i use the opsw

tony

On Jul 15, 2018, at 7:10 AM, Steve_G <RailRodder@...> wrote:

Hi Tony
Ensure that the autotrain loco has been fully released from all other

throttles before attempting to create the train. Autotrain will not
work on a shared throttle. You can clear all command station slots with
an OpSw, see the digitrax documention for which one.

LocoNet slot monitor can be a good start to finding inuse throttles.
Steve G.

On July 15, 2018 1:59:00 AM EDT, AD <bklyns_baseball_club@...>

wrote:

please help as i am having a new issues with an engine running on
automatic mode

run a auto train
sometimes it makes it thru a loop. my throttle shows its speed
then randomly it stops and the throttle shows 0 speed
i switch to manual mode and use speed lever above 0 and it goes only

to

stop again. speed lever went to 0
so i switch to auto and it goes.

i terminate train
i cant control the engine with my physical throttle
i write all sheets on the programming track
now throttle control e.ngine

please tell me what i am doing wrong or whats going on

tony

On Jul 15, 2018, at 1:00 AM, AD <bklyns_baseball_club@...>

wrote:

please ignore these 2 emails, my perferences were not all set to

loconet.

train running but pauses randomly during the loop

any reason for that

tony

On Jul 15, 2018, at 12:26 AM, AD <bklyns_baseball_club@...>

wrote:

ps: if i use the autotrain window to switch to manual and use the

speed lever to move the train it doesnt respond either

what am i doing wrong

tony

On Jul 15, 2018, at 12:18 AM, AD <bklyns_baseball_club@...>

wrote:

i have my layout connected to computer running jmri 4.12. a

layout

panel using sml signals.

sections are defined.transits are defined. dispatcher settings

are

set to run train automatically.

enter a train name, dcc address etc.
click on add train
the active train window lists the train. status=running /

mode=automatic / allocated section is the next section from the one
train starts in

requested allocation waiting for dipatch window shows train and

lists the next section after the one allocated

allocated sections shows the train in iy12 as occupied and shows

iy13 as unoccupied

everything looks good except the train is not running

how do i get it to start. looks like the program assumed it

running but it never moved

in the settings when i entered its dcc address of 5512 it shows

as

5,512

if i run the train with a physical throttle the allocated

sections

table lists the sections in and the next one changing each as the
engine moves.

how do i get the train to physically run automatically


tony

--
Sent from my Android device with K-9 Mail. Please excuse my brevity.

---------- Original Message ----------
From: AD <bklyns_baseball_club@...>
Date: July 15, 2018 at 4:41 PM


possible program ommission

in transits edit window there is no way to enter a comment

tony

On Jul 15, 2018, at 2:51 PM, AD <bklyns_baseball_club@...> wrote:

i cant find such an opsw
will filling the physical throttle with other addresses do the job
must it be removed from the wifi list of addresses but not bein used on one
of the 4 throttles

tony

On Jul 15, 2018, at 2:33 PM, AD <bklyns_baseball_club@...> wrote:

so i cant have an engine in auto train and on my physical throttle at the
same time.
will disconnecting the physical throttle be ok or must i use the opsw

tony

On Jul 15, 2018, at 7:10 AM, Steve_G <RailRodder@...> wrote:

Hi Tony
Ensure that the autotrain loco has been fully released from all other
throttles before attempting to create the train. Autotrain will not work
on a shared throttle. You can clear all command station slots with an
OpSw, see the digitrax documention for which one.
LocoNet slot monitor can be a good start to finding inuse throttles.
Steve G.

On July 15, 2018 1:59:00 AM EDT, AD <bklyns_baseball_club@...> wrote:
please help as i am having a new issues with an engine running on
automatic mode

run a auto train
sometimes it makes it thru a loop. my throttle shows its speed
then randomly it stops and the throttle shows 0 speed
i switch to manual mode and use speed lever above 0 and it goes only to
stop again. speed lever went to 0
so i switch to auto and it goes.

i terminate train
i cant control the engine with my physical throttle
i write all sheets on the programming track
now throttle control e.ngine

please tell me what i am doing wrong or whats going on

tony

On Jul 15, 2018, at 1:00 AM, AD <bklyns_baseball_club@...> wrote:

please ignore these 2 emails, my perferences were not all set to

loconet.

train running but pauses randomly during the loop

any reason for that

tony

On Jul 15, 2018, at 12:26 AM, AD <bklyns_baseball_club@...>

wrote:

ps: if i use the autotrain window to switch to manual and use the

speed lever to move the train it doesnt respond either

what am i doing wrong

tony

On Jul 15, 2018, at 12:18 AM, AD <bklyns_baseball_club@...>

wrote:

i have my layout connected to computer running jmri 4.12. a layout

panel using sml signals.

sections are defined.transits are defined. dispatcher settings are

set to run train automatically.

enter a train name, dcc address etc.
click on add train
the active train window lists the train. status=running /

mode=automatic / allocated section is the next section from the one
train starts in

requested allocation waiting for dipatch window shows train and

lists the next section after the one allocated

allocated sections shows the train in iy12 as occupied and shows

iy13 as unoccupied

everything looks good except the train is not running

how do i get it to start. looks like the program assumed it

running but it never moved

in the settings when i entered its dcc address of 5512 it shows as

5,512

if i run the train with a physical throttle the allocated sections

table lists the sections in and the next one changing each as the
engine moves.

how do i get the train to physically run automatically


tony

--
Sent from my Android device with K-9 Mail. Please excuse my brevity.