Locked Something I don't understand - signals not updating #signals
|
?
Whern I first start my layout (very simple one). The signaling doesn't update, all the signals are red.
?
What's wrong ?
?
?
---------------------------------------------
Jean-Louis Paris-France
---------------------------------------------
JRMI 5.8 on Windows
DCC EX? on Arduino Mega
Java version 17.1.12
?
|
|
Jean-Louis, The most likely issue is that you have not initialized the internal direction sensors that Dispatcher adds to the SSL. The Sensors table "Defaults -> Initial Sensor State" menu item can be used to set the initial state of the internal sensors. ?Select the "Inactive" option. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: [jmriusers] Something I don't understand Date: Sunday, October 20, 2024 8:45 AM ? Whern I first start my layout (very simple one). The signaling doesn't update, all the signals are red. ? What's wrong ? ? ? --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? |
|
Sorry dave but I was not able to find this option in the sensor table.? Can you explain? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ?: [email protected] ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 16:43:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean-Louis, The most likely issue is that you have not initialized the internal direction sensors that Dispatcher adds to the SSL. The Sensors table "Defaults -> Initial Sensor State" menu item can be used to set the initial state of the internal sensors. ?Select the "Inactive" option. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: [jmriusers] Something I don't understand Date: Sunday, October 20, 2024 8:45 AM ? Whern I first start my layout (very simple one). The signaling doesn't update, all the signals are red. ? What's wrong ? ? ? --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- ---------------------------------------------
Jean-Louis Paris-France
---------------------------------------------
JRMI 5.8 on Windows
DCC EX? on Arduino Mega
Java version 17.1.12
? |
|
Look in the Sensor table menu bar. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:07 AM Sorry dave but I was not able to find this option in the sensor table.? Can you explain? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 16:43:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean-Louis, The most likely issue is that you have not initialized the internal direction sensors that Dispatcher adds to the SSL. The Sensors table "Defaults -> Initial Sensor State" menu item can be used to set the initial state of the internal sensors. ?Select the "Inactive" option. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: [jmriusers] Something I don't understand Date: Sunday, October 20, 2024 8:45 AM ? Whern I first start my layout (very simple one). The signaling doesn't update, all the signals are red. ? What's wrong ? ? ? --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? |
|
Sorry Dave, I change the option, run again JRMI but the reszul? t is still the same.? No change in signaling. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ?: [email protected] ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:12:23 Objet: Re: [jmriusers] Something I don't understand - signals not updating Look in the Sensor table menu bar. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:07 AM Sorry dave but I was not able to find this option in the sensor table.? Can you explain? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 16:43:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean-Louis, The most likely issue is that you have not initialized the internal direction sensors that Dispatcher adds to the SSL. The Sensors table "Defaults -> Initial Sensor State" menu item can be used to set the initial state of the internal sensors. ?Select the "Inactive" option. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: [jmriusers] Something I don't understand Date: Sunday, October 20, 2024 8:45 AM ? Whern I first start my layout (very simple one). The signaling doesn't update, all the signals are red. ? What's wrong ? ? ? --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- ---------------------------------------------
Jean-Louis Paris-France
---------------------------------------------
JRMI 5.8 on Windows
DCC EX? on Arduino Mega
Java version 17.1.12
? |
|
If you upload the xml file to group's ProblemsBeingWorkedOn file folder, we can review it. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:24 AM Sorry Dave, I change the option, run again JRMI but the reszul? t is still the same.? No change in signaling. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:12:23 Objet: Re: [jmriusers] Something I don't understand - signals not updating Look in the Sensor table menu bar. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:07 AM Sorry dave but I was not able to find this option in the sensor table.? Can you explain? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 16:43:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean-Louis, The most likely issue is that you have not initialized the internal direction sensors that Dispatcher adds to the SSL. The Sensors table "Defaults -> Initial Sensor State" menu item can be used to set the initial state of the internal sensors. ?Select the "Inactive" option. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: [jmriusers] Something I don't understand Date: Sunday, October 20, 2024 8:45 AM ? Whern I first start my layout (very simple one). The signaling doesn't update, all the signals are red. ? What's wrong ? ? ? --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? |
|
The signaling is correct after I cbange the turnouts,? it looks like the turnouts state is not knowm? while I run a script to in the start up menu that is supposed to close all the switches. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ?: [email protected] ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:12:23 Objet: Re: [jmriusers] Something I don't understand - signals not updating Look in the Sensor table menu bar. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:07 AM Sorry dave but I was not able to find this option in the sensor table.? Can you explain? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 16:43:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean-Louis, The most likely issue is that you have not initialized the internal direction sensors that Dispatcher adds to the SSL. The Sensors table "Defaults -> Initial Sensor State" menu item can be used to set the initial state of the internal sensors. ?Select the "Inactive" option. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: [jmriusers] Something I don't understand Date: Sunday, October 20, 2024 8:45 AM ? Whern I first start my layout (very simple one). The signaling doesn't update, all the signals are red. ? What's wrong ? ? ? --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- ---------------------------------------------
Jean-Louis Paris-France
---------------------------------------------
JRMI 5.8 on Windows
DCC EX? on Arduino Mega
Java version 17.1.12
? |
|
Wich one ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ?: [email protected] ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:26:34 Objet: Re: [jmriusers] Something I don't understand - signals not updating If you upload the xml file to group's ProblemsBeingWorkedOn file folder, we can review it. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:24 AM Sorry Dave, I change the option, run again JRMI but the reszul? t is still the same.? No change in signaling. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:12:23 Objet: Re: [jmriusers] Something I don't understand - signals not updating Look in the Sensor table menu bar. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:07 AM Sorry dave but I was not able to find this option in the sensor table.? Can you explain? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 16:43:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean-Louis, The most likely issue is that you have not initialized the internal direction sensors that Dispatcher adds to the SSL. The Sensors table "Defaults -> Initial Sensor State" menu item can be used to set the initial state of the internal sensors. ?Select the "Inactive" option. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: [jmriusers] Something I don't understand Date: Sunday, October 20, 2024 8:45 AM ? Whern I first start my layout (very simple one). The signaling doesn't update, all the signals are red. ? What's wrong ? ? ? --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- ---------------------------------------------
Jean-Louis Paris-France
---------------------------------------------
JRMI 5.8 on Windows
DCC EX? on Arduino Mega
Java version 17.1.12
? |
|
The one that you load after starting PanelPro. ?Note: ?Never load more than one xml file during a PanelPro session. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:35 AM Wich one ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:26:34 Objet: Re: [jmriusers] Something I don't understand - signals not updating If you upload the xml file to group's ProblemsBeingWorkedOn file folder, we can review it. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:24 AM Sorry Dave, I change the option, run again JRMI but the reszul? t is still the same.? No change in signaling. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:12:23 Objet: Re: [jmriusers] Something I don't understand - signals not updating Look in the Sensor table menu bar. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:07 AM Sorry dave but I was not able to find this option in the sensor table.? Can you explain? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 16:43:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean-Louis, The most likely issue is that you have not initialized the internal direction sensors that Dispatcher adds to the SSL. The Sensors table "Defaults -> Initial Sensor State" menu item can be used to set the initial state of the internal sensors. ?Select the "Inactive" option. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: [jmriusers] Something I don't understand Date: Sunday, October 20, 2024 8:45 AM ? Whern I first start my layout (very simple one). The signaling doesn't update, all the signals are red. ? What's wrong ? ? ? --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? |
|
OK but sorry to be a a pain, but how can I find the ProblemsBeingWorkedOn group ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ?: [email protected] ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:42:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating The one that you load after starting PanelPro. ?Note: ?Never load more than one xml file during a PanelPro session. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:35 AM Wich one ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:26:34 Objet: Re: [jmriusers] Something I don't understand - signals not updating If you upload the xml file to group's ProblemsBeingWorkedOn file folder, we can review it. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:24 AM Sorry Dave, I change the option, run again JRMI but the reszul? t is still the same.? No change in signaling. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:12:23 Objet: Re: [jmriusers] Something I don't understand - signals not updating Look in the Sensor table menu bar. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:07 AM Sorry dave but I was not able to find this option in the sensor table.? Can you explain? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 16:43:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean-Louis, The most likely issue is that you have not initialized the internal direction sensors that Dispatcher adds to the SSL. The Sensors table "Defaults -> Initial Sensor State" menu item can be used to set the initial state of the internal sensors. ?Select the "Inactive" option. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: [jmriusers] Something I don't understand Date: Sunday, October 20, 2024 8:45 AM ? Whern I first start my layout (very simple one). The signaling doesn't update, all the signals are red. ? What's wrong ? ? ? --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- ---------------------------------------------
Jean-Louis Paris-France
---------------------------------------------
JRMI 5.8 on Windows
DCC EX? on Arduino Mega
Java version 17.1.12
? |
|
"jmriusers" is a group at?/g/jmriusers. ?In the left column is a selection for "Files". ?When you click on that, scroll down to "ProblemsBeingWorkedOn" and click on it. ?Then click on the "New/Upload" button to upload a file. You might need to logon with your groups.io account name and password. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:50 AM OK but sorry to be a a pain, but how can I find the ProblemsBeingWorkedOn group ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:42:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating The one that you load after starting PanelPro. ?Note: ?Never load more than one xml file during a PanelPro session. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:35 AM Wich one ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:26:34 Objet: Re: [jmriusers] Something I don't understand - signals not updating If you upload the xml file to group's ProblemsBeingWorkedOn file folder, we can review it. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:24 AM Sorry Dave, I change the option, run again JRMI but the reszul? t is still the same.? No change in signaling. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:12:23 Objet: Re: [jmriusers] Something I don't understand - signals not updating Look in the Sensor table menu bar. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:07 AM Sorry dave but I was not able to find this option in the sensor table.? Can you explain? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 16:43:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean-Louis, The most likely issue is that you have not initialized the internal direction sensors that Dispatcher adds to the SSL. The Sensors table "Defaults -> Initial Sensor State" menu item can be used to set the initial state of the internal sensors. ?Select the "Inactive" option. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: [jmriusers] Something I don't understand Date: Sunday, October 20, 2024 8:45 AM ? Whern I first start my layout (very simple one). The signaling doesn't update, all the signals are red. ? What's wrong ? ? ? --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? |
|
Dave, I did it. It is tables.xml uploaded by Jean-Louis Free.? Thanks. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ?: [email protected] ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:57:07 Objet: Re: [jmriusers] Something I don't understand - signals not updating "jmriusers" is a group at?/g/jmriusers. ?In the left column is a selection for "Files". ?When you click on that, scroll down to "ProblemsBeingWorkedOn" and click on it. ?Then click on the "New/Upload" button to upload a file. You might need to logon with your groups.io account name and password. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:50 AM OK but sorry to be a a pain, but how can I find the ProblemsBeingWorkedOn group ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:42:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating The one that you load after starting PanelPro. ?Note: ?Never load more than one xml file during a PanelPro session. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:35 AM Wich one ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:26:34 Objet: Re: [jmriusers] Something I don't understand - signals not updating If you upload the xml file to group's ProblemsBeingWorkedOn file folder, we can review it. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:24 AM Sorry Dave, I change the option, run again JRMI but the reszul? t is still the same.? No change in signaling. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:12:23 Objet: Re: [jmriusers] Something I don't understand - signals not updating Look in the Sensor table menu bar. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:07 AM Sorry dave but I was not able to find this option in the sensor table.? Can you explain? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 16:43:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean-Louis, The most likely issue is that you have not initialized the internal direction sensors that Dispatcher adds to the SSL. The Sensors table "Defaults -> Initial Sensor State" menu item can be used to set the initial state of the internal sensors. ?Select the "Inactive" option. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: [jmriusers] Something I don't understand Date: Sunday, October 20, 2024 8:45 AM ? Whern I first start my layout (very simple one). The signaling doesn't update, all the signals are red. ? What's wrong ? ? ? --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- ---------------------------------------------
Jean-Louis Paris-France
---------------------------------------------
JRMI 5.8 on Windows
DCC EX? on Arduino Mega
Java version 17.1.12
? |
|
Jean Louis, There are a couple of minor changes that I would recommend. In the Layout Editor menu, select Tools -> Check. ?The various sub menus are handy for validation. ?You have an end bumper sitting to the left of the spur track. ?That can be deleted. ?The spur track is connected to an anchor point. ?It is showing yellow which indicates an error. ?It turns out that there is also an end bumper at the same location. ?After moving the anchor point, you can see the end bumper. ?Delete it. ?Then use the right click menu on the anchor point to change it to an end bumper. ? I prefer to use LogixNG for initialization. ?Since you already have a Route for setting the turnouts, a simple LogixNG works nicely. Since I am running in simulation mode, I also created a route for the occupancy sensors. Note: ?DCC++ simulation does not work well so I use LocoNet simulation with the connection prefix set to D. ?I also had to change the turnout feedback to DIRECT. After the changes, the signals work and running an Dispatcher auto train works properly. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 11:07 AM Dave, I did it. It is tables.xml uploaded by Jean-Louis Free.? Thanks. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:57:07 Objet: Re: [jmriusers] Something I don't understand - signals not updating "jmriusers" is a group at?/g/jmriusers. ?In the left column is a selection for "Files". ?When you click on that, scroll down to "ProblemsBeingWorkedOn" and click on it. ?Then click on the "New/Upload" button to upload a file. You might need to logon with your groups.io account name and password. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:50 AM OK but sorry to be a a pain, but how can I find the ProblemsBeingWorkedOn group ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:42:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating The one that you load after starting PanelPro. ?Note: ?Never load more than one xml file during a PanelPro session. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:35 AM Wich one ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:26:34 Objet: Re: [jmriusers] Something I don't understand - signals not updating If you upload the xml file to group's ProblemsBeingWorkedOn file folder, we can review it. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:24 AM Sorry Dave, I change the option, run again JRMI but the reszul? t is still the same.? No change in signaling. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:12:23 Objet: Re: [jmriusers] Something I don't understand - signals not updating Look in the Sensor table menu bar. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:07 AM Sorry dave but I was not able to find this option in the sensor table.? Can you explain? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 16:43:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean-Louis, The most likely issue is that you have not initialized the internal direction sensors that Dispatcher adds to the SSL. The Sensors table "Defaults -> Initial Sensor State" menu item can be used to set the initial state of the internal sensors. ?Select the "Inactive" option. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: [jmriusers] Something I don't understand Date: Sunday, October 20, 2024 8:45 AM ? Whern I first start my layout (very simple one). The signaling doesn't update, all the signals are red. ? What's wrong ? ? ? --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? |
|
Many thanks Dave.? I will have a look later (diner time here in Paris), and keep you informed. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ?: [email protected] ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 19:21:09 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean Louis, There are a couple of minor changes that I would recommend. In the Layout Editor menu, select Tools -> Check. ?The various sub menus are handy for validation. ?You have an end bumper sitting to the left of the spur track. ?That can be deleted. ?The spur track is connected to an anchor point. ?It is showing yellow which indicates an error. ?It turns out that there is also an end bumper at the same location. ?After moving the anchor point, you can see the end bumper. ?Delete it. ?Then use the right click menu on the anchor point to change it to an end bumper. ? I prefer to use LogixNG for initialization. ?Since you already have a Route for setting the turnouts, a simple LogixNG works nicely. Since I am running in simulation mode, I also created a route for the occupancy sensors. Note: ?DCC++ simulation does not work well so I use LocoNet simulation with the connection prefix set to D. ?I also had to change the turnout feedback to DIRECT. After the changes, the signals work and running an Dispatcher auto train works properly. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 11:07 AM Dave, I did it. It is tables.xml uploaded by Jean-Louis Free.? Thanks. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:57:07 Objet: Re: [jmriusers] Something I don't understand - signals not updating "jmriusers" is a group at?/g/jmriusers. ?In the left column is a selection for "Files". ?When you click on that, scroll down to "ProblemsBeingWorkedOn" and click on it. ?Then click on the "New/Upload" button to upload a file. You might need to logon with your groups.io account name and password. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:50 AM OK but sorry to be a a pain, but how can I find the ProblemsBeingWorkedOn group ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:42:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating The one that you load after starting PanelPro. ?Note: ?Never load more than one xml file during a PanelPro session. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:35 AM Wich one ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:26:34 Objet: Re: [jmriusers] Something I don't understand - signals not updating If you upload the xml file to group's ProblemsBeingWorkedOn file folder, we can review it. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:24 AM Sorry Dave, I change the option, run again JRMI but the reszul? t is still the same.? No change in signaling. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:12:23 Objet: Re: [jmriusers] Something I don't understand - signals not updating Look in the Sensor table menu bar. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:07 AM Sorry dave but I was not able to find this option in the sensor table.? Can you explain? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 16:43:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean-Louis, The most likely issue is that you have not initialized the internal direction sensors that Dispatcher adds to the SSL. The Sensors table "Defaults -> Initial Sensor State" menu item can be used to set the initial state of the internal sensors. ?Select the "Inactive" option. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: [jmriusers] Something I don't understand Date: Sunday, October 20, 2024 8:45 AM ? Whern I first start my layout (very simple one). The signaling doesn't update, all the signals are red. ? What's wrong ? ? ? --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- ---------------------------------------------
Jean-Louis Paris-France
---------------------------------------------
JRMI 5.8 on Windows
DCC EX? on Arduino Mega
Java version 17.1.12
? |
|
Jean,
After starting up, take a look at the Sensor and Turnout table. If any sensor or turnout is showing Unknown, it will cause the signal logic to display Stop or stay Red. I don't remember if you are using mast or heads for the signal logic. But if either system sees something as Unknown, it will not give any other display. -Ken Cameron, Member JMRI Dev Team www.jmri.org www.fingerlakeslivesteamers.org www.cnymod.com |
|
Dave, How do you do LogixNG initialization ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ?: [email protected] ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 19:21:09 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean Louis, There are a couple of minor changes that I would recommend. In the Layout Editor menu, select Tools -> Check. ?The various sub menus are handy for validation. ?You have an end bumper sitting to the left of the spur track. ?That can be deleted. ?The spur track is connected to an anchor point. ?It is showing yellow which indicates an error. ?It turns out that there is also an end bumper at the same location. ?After moving the anchor point, you can see the end bumper. ?Delete it. ?Then use the right click menu on the anchor point to change it to an end bumper. ? I prefer to use LogixNG for initialization. ?Since you already have a Route for setting the turnouts, a simple LogixNG works nicely. Since I am running in simulation mode, I also created a route for the occupancy sensors. Note: ?DCC++ simulation does not work well so I use LocoNet simulation with the connection prefix set to D. ?I also had to change the turnout feedback to DIRECT. After the changes, the signals work and running an Dispatcher auto train works properly. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 11:07 AM Dave, I did it. It is tables.xml uploaded by Jean-Louis Free.? Thanks. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:57:07 Objet: Re: [jmriusers] Something I don't understand - signals not updating "jmriusers" is a group at?/g/jmriusers. ?In the left column is a selection for "Files". ?When you click on that, scroll down to "ProblemsBeingWorkedOn" and click on it. ?Then click on the "New/Upload" button to upload a file. You might need to logon with your groups.io account name and password. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:50 AM OK but sorry to be a a pain, but how can I find the ProblemsBeingWorkedOn group ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:42:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating The one that you load after starting PanelPro. ?Note: ?Never load more than one xml file during a PanelPro session. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:35 AM Wich one ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:26:34 Objet: Re: [jmriusers] Something I don't understand - signals not updating If you upload the xml file to group's ProblemsBeingWorkedOn file folder, we can review it. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:24 AM Sorry Dave, I change the option, run again JRMI but the reszul? t is still the same.? No change in signaling. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:12:23 Objet: Re: [jmriusers] Something I don't understand - signals not updating Look in the Sensor table menu bar. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:07 AM Sorry dave but I was not able to find this option in the sensor table.? Can you explain? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 16:43:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean-Louis, The most likely issue is that you have not initialized the internal direction sensors that Dispatcher adds to the SSL. The Sensors table "Defaults -> Initial Sensor State" menu item can be used to set the initial state of the internal sensors. ?Select the "Inactive" option. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: [jmriusers] Something I don't understand Date: Sunday, October 20, 2024 8:45 AM ? Whern I first start my layout (very simple one). The signaling doesn't update, all the signals are red. ? What's wrong ? ? ? --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- ---------------------------------------------
Jean-Louis Paris-France
---------------------------------------------
JRMI 5.8 on Windows
DCC EX? on Arduino Mega
Java version 17.1.12
? |
|
The introduction to LogixNG is at? Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Monday, October 21, 2024 12:18 AM Dave, How do you do LogixNG initialization ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 19:21:09 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean Louis, There are a couple of minor changes that I would recommend. In the Layout Editor menu, select Tools -> Check. ?The various sub menus are handy for validation. ?You have an end bumper sitting to the left of the spur track. ?That can be deleted. ?The spur track is connected to an anchor point. ?It is showing yellow which indicates an error. ?It turns out that there is also an end bumper at the same location. ?After moving the anchor point, you can see the end bumper. ?Delete it. ?Then use the right click menu on the anchor point to change it to an end bumper. ? I prefer to use LogixNG for initialization. ?Since you already have a Route for setting the turnouts, a simple LogixNG works nicely. Since I am running in simulation mode, I also created a route for the occupancy sensors. Note: ?DCC++ simulation does not work well so I use LocoNet simulation with the connection prefix set to D. ?I also had to change the turnout feedback to DIRECT. After the changes, the signals work and running an Dispatcher auto train works properly. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 11:07 AM Dave, I did it. It is tables.xml uploaded by Jean-Louis Free.? Thanks. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:57:07 Objet: Re: [jmriusers] Something I don't understand - signals not updating "jmriusers" is a group at?/g/jmriusers. ?In the left column is a selection for "Files". ?When you click on that, scroll down to "ProblemsBeingWorkedOn" and click on it. ?Then click on the "New/Upload" button to upload a file. You might need to logon with your groups.io account name and password. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:50 AM OK but sorry to be a a pain, but how can I find the ProblemsBeingWorkedOn group ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:42:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating The one that you load after starting PanelPro. ?Note: ?Never load more than one xml file during a PanelPro session. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:35 AM Wich one ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:26:34 Objet: Re: [jmriusers] Something I don't understand - signals not updating If you upload the xml file to group's ProblemsBeingWorkedOn file folder, we can review it. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:24 AM Sorry Dave, I change the option, run again JRMI but the reszul? t is still the same.? No change in signaling. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:12:23 Objet: Re: [jmriusers] Something I don't understand - signals not updating Look in the Sensor table menu bar. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:07 AM Sorry dave but I was not able to find this option in the sensor table.? Can you explain? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 16:43:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean-Louis, The most likely issue is that you have not initialized the internal direction sensors that Dispatcher adds to the SSL. The Sensors table "Defaults -> Initial Sensor State" menu item can be used to set the initial state of the internal sensors. ?Select the "Inactive" option. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: [jmriusers] Something I don't understand Date: Sunday, October 20, 2024 8:45 AM ? Whern I first start my layout (very simple one). The signaling doesn't update, all the signals are red. ? What's wrong ? ? ? --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? |
|
Thanks dave, I'll have a look. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ?: [email protected] ·¡²Ô±¹´Ç²â¨¦: Lundi 21 Octobre 2024 17:45:27 Objet: Re: [jmriusers] Something I don't understand - signals not updating The introduction to LogixNG is at? Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Monday, October 21, 2024 12:18 AM Dave, How do you do LogixNG initialization ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 19:21:09 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean Louis, There are a couple of minor changes that I would recommend. In the Layout Editor menu, select Tools -> Check. ?The various sub menus are handy for validation. ?You have an end bumper sitting to the left of the spur track. ?That can be deleted. ?The spur track is connected to an anchor point. ?It is showing yellow which indicates an error. ?It turns out that there is also an end bumper at the same location. ?After moving the anchor point, you can see the end bumper. ?Delete it. ?Then use the right click menu on the anchor point to change it to an end bumper. ? I prefer to use LogixNG for initialization. ?Since you already have a Route for setting the turnouts, a simple LogixNG works nicely. Since I am running in simulation mode, I also created a route for the occupancy sensors. Note: ?DCC++ simulation does not work well so I use LocoNet simulation with the connection prefix set to D. ?I also had to change the turnout feedback to DIRECT. After the changes, the signals work and running an Dispatcher auto train works properly. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 11:07 AM Dave, I did it. It is tables.xml uploaded by Jean-Louis Free.? Thanks. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:57:07 Objet: Re: [jmriusers] Something I don't understand - signals not updating "jmriusers" is a group at?/g/jmriusers. ?In the left column is a selection for "Files". ?When you click on that, scroll down to "ProblemsBeingWorkedOn" and click on it. ?Then click on the "New/Upload" button to upload a file. You might need to logon with your groups.io account name and password. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:50 AM OK but sorry to be a a pain, but how can I find the ProblemsBeingWorkedOn group ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:42:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating The one that you load after starting PanelPro. ?Note: ?Never load more than one xml file during a PanelPro session. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:35 AM Wich one ? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:26:34 Objet: Re: [jmriusers] Something I don't understand - signals not updating If you upload the xml file to group's ProblemsBeingWorkedOn file folder, we can review it. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:24 AM Sorry Dave, I change the option, run again JRMI but the reszul? t is still the same.? No change in signaling. JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 17:12:23 Objet: Re: [jmriusers] Something I don't understand - signals not updating Look in the Sensor table menu bar. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: Re: [jmriusers] Something I don't understand - signals not updating Date: Sunday, October 20, 2024 10:07 AM Sorry dave but I was not able to find this option in the sensor table.? Can you explain? JeanLouisDelestre@... De: "Dave Sand" <ds@...> ·¡²Ô±¹´Ç²â¨¦: Dimanche 20 Octobre 2024 16:43:38 Objet: Re: [jmriusers] Something I don't understand - signals not updating Jean-Louis, The most likely issue is that you have not initialized the internal direction sensors that Dispatcher adds to the SSL. The Sensors table "Defaults -> Initial Sensor State" menu item can be used to set the initial state of the internal sensors. ?Select the "Inactive" option. Dave Sand ----- Original message ----- From: Jean-Louis Free <jeanlouisdelestre@...> Subject: [jmriusers] Something I don't understand Date: Sunday, October 20, 2024 8:45 AM ? Whern I first start my layout (very simple one). The signaling doesn't update, all the signals are red. ? What's wrong ? ? ? --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- --------------------------------------------- Jean-Louis Paris-France --------------------------------------------- JRMI 5.8 on Windows DCC EX? on Arduino Mega Java version 17.1.12 ? -- ---------------------------------------------
Jean-Louis Paris-France
---------------------------------------------
JRMI 5.8 on Windows
DCC EX? on Arduino Mega
Java version 17.1.12
? |
Ken Cameron