开云体育

Benny,

You might try resetting the block paths.? Select Tools >> Blocks.? From the Block table menu select Paths >> Delete Paths.? Save the panel file and stop JMRI.? When you start and load the panel file, the paths will be re-built.? Sometimes this will clear up block routing issues.

If that does not help, upload the panel file to ProblemsBeingWorkedOn and I will take a look at it.


Dave Sand



> On Aug 20, 2018, at 3:19 PM, Benny Tj?der <etxbct@...> wrote:
>
> Ok, than i know since some times it does not change and I probobly click A to B than.
>
> Another question. I get strange routing, instead of going direct from point A to D it selects turnout from A on track 1 down to track 2 and down to track 3 and than back to track 1 out to D.
> Can I make jmri build next hop in a different way? I tried to set metric but it does not work.
>
> /Benny
>
> Den m?n 20 aug 2018 22:11Dave Sand <ds@...> skrev:
> Benny,
>
> I did some testing.? I can re-create your problem if I to a multi-segment selection.? By that I mean I select A and C instead of A and B followed by B and C.
>
> I will add this to my todo list.
>
>
> Dave Sand
>
>
>
> > On Aug 20, 2018, at 2:53 PM, Dave Sand <ds@...> wrote:
> >
> > Benny,
> >
> > Normally you want to select the Clear option.? This disables the option to use a different color during route setup.
> >
> > The theory behind this option is to let the dispatcher know that the route is being set.? Once the setup is complete and the specified time has expired, the track and extra colors go back to the assigned values.? If an error occurs during the setup process, the temporary track and extra colors remain.? There might have been an error recorded in the system console.
> >
> >
> > Dave Sand
> >
> >
> >
> >> On Aug 20, 2018, at 2:39 PM, Benny Tj?der <etxbct@...> wrote:
> >>
> >> It was set to white. I have changed it to green and than I get track color changed to green instead.
> >> So after I have set an entryexit it turn to alternate color, which is green. If I clear it i get green on some tracks and black on most of the tracks. So it changes the track color from black to green.
> >>
> >> /Benny
> >>
> >> Den s?n 19 aug 2018 21:52Dave Sand <ds@...> skrev:
> >> Benny,
> >>
> >> Use Layout Editor Tools to open the Entry/Exit table.? Select Options >> Options from the table menu.
> >>
> >> What color do you have set for “Initial color of path”?? Based on your description it appears to be White.
> >>
> >> If the setup process is interrupted for any reason, the track and extra colors are not set back.? A subsequent save will update the panel xml file.
> >>
> >>
> >> Dave Sand
> >>
> >>
> >>
> >>> On Aug 19, 2018, at 1:21 PM, Benny Tj?der <etxbct@...> wrote:
> >>>
> >>> In JMRI 4.12 the color on tracks is changed when an NX is activated.
> >>> Track color is changed from black to white on some of the blocks, not all, and extracolor is changed from green to white on same blocks. The only color not changed is the occupiedcolor.
> >>>
> >>> Before setting an EntryExit:
> >>> <layoutblock? systemName="ILB29" occupancysensor="dSIIa" occupidsense="2" trackcolor="black" occupiedcolor="red" extracolor="green">
> >>>? ? <systemName>ILB29</systemName>
> >>>? ? <userName>SIIa</userName>
> >>> </layoutblock>
> >>> After:
> >>> <layoutblock? systemName="ILB29" occupancysensor="dSIIa" occupidsense="2" trackcolor="white" occupiedcolor="red" extracolor="white">
> >>>? ? <systemName>ILB29</systemName>
> >>>? ? <userName>SIIa</userName>
> >>> </layoutblock>
> >>>
> >>> /Best regards
> >>> Benny
> >>>
> >>
> >>
> >>
> >>
> >>
> >
> >
> >
>
>
>
>
>