Dear Spuds,
I deleted the one slot entry. It was not a road number, but an
EOS..? slot. Sorry, I should've taken a screen shot.
Still having the same issues with the WIThrottle not allowing me to
address certain loco numbers:
Once I've programmed an address, in this case 6035, when I try to
enter the address a second time I get the prompt: "Loco 6035(L)
In-Use Would you like to acquire this address?" When I click the YES
button nothing happens, even with repeated pressing. When I click
the NO button the window disappears, but the cycle repeats and
remains NOT SET. This seems totally random. For example I just tried
entering "03," which has not been a problem. Now I get the same
prompt.
I can acquire, control and release all numbers with the JMRI
throttle.
I can acquire, control and release all numbers with the Digitrax 402
throttle.
This has really got me stumped.
Attached below as a JPEG are screenshots of all the JMRI screens in
my current configuration. Perhaps this will give us a clue?
Regards,
Robert Diepenbrock
On 7/25/18 1:53 AM, Spuds McCat wrote:
toggle quoted message
Show quoted text
You should always dispatch a loco, stealing is
bad. :)
Is your phone connected to the same wifi Jmri
is, and as such using withrottle, or on the lnwi's private
wifi, and as such talking to it?
I suggest opening up (under loconet) the slot
monitor, and clearing the slots with the misbehaving engine
numbers.
Dear Spuds,
Thanks for your reply.
I Upgraded to JMRI 4.12 which solved the iso-track
programming issue.
Still having the WiThrottle issue. I have a query into JMRI
tech Support.
The WiThrottle will not allow me to change addresses. Once
I've programmed an address, in this case 6035, when I try to
enter the address a second time I get the prompt: "Loco
6035(L) In-Use Would you like to acquire this address?" When
I click the YES button nothing happens, even with repeated
pressing. When I click the NO button the window disappears,
but the cycle repeats and remains NOT SET. I tried to delete
the Roster addresses, It's like the WiThrottle gets
"stuck."I also get the prompt "Unable to load JMRI WebServer
page."
This issue is across three different devices, one iPad and 2
iPhone, get the same prompt and the same non-function.
This issue only occurs with certain 4 digit numbers. Below
is a comparison "Chart."
Loco Address??? Digitrax Throttle??? JMRI Throttle
(computer)??? WiThrottle
6005??? ??? ??? ??? OK??? ??? ??? ??? ??? ???? OK??? ??? ???
??? ??? ??? ??? ??? ??? ? OK
6035??? ??? ??? ??? OK??? ??? ??? ??? ??? ???? OK??? ??? ???
??? ??? ??? ??? ??? ??? ? NO
6051 ?? ??? ??? ??? OK??? ??? ??? ??? ??? ???? OK??? ??? ???
??? ??? ??? ??? ??? ??? ? OK
7614??? ??? ??? ??? OK??? ??? ??? ??? ??? ???? OK??? ??? ???
??? ??? ??? ??? ??? ??? ? NO
3??? ??? ??? ??? ??? ? OK??? ??? ??? ??? ??? ???? OK??? ???
??? ??? ??? ??? ??? ??? ??? ? OK
See images below:
An additional issue is I can't get JMRI ProgramPro Throttle
(on my computer) to run locomotives.
The Digitrax throttle runs everything fine.?
?
Any ideas?
THANKS in advance for the help.
Robert Diepenbrock
![]()
On
7/24/18 11:05 AM, Spuds McCat wrote:
4.10 has some loconet slot 'issues',
upgrade to 4.12 which came out last week.?
How is the computer/Jmri connected to
the 240?
The LW?I is independant from JMRI, a
phone connected to it wont show in JMRI
Dear
JMRI Users,
I just joined the group and this is my first post. To
all you WiThrottle-JMRI-Mac "gurus,"
I recently converted my N Scale layout from DC to DCC.
I installed a Digitrax DSC240 Advance Command Station
with Digitrax LNWI Loconet Wifi Interface.
I downloaded JMRI Panel Pro and Decoder Pro 4.10
Software and installed it on my MacBook Pro running
OSX 10.10.2 Yosemite
I purchased, downloaded and installed WiThrottle on my
iPad.
The Digitrax DSC240 Advance Command Station is
connected to an isolated programming track per the
manual. The WiThrottle is connected via the Digitrax
LNWI Loconet Wifi Interface.
I'm having two issues:
1. I cannot program any locomotives on the
isolated programming track.
The JMRI Decoder Pro software is giving me
the prompt: "Programmer error. Programmer busy (302)"
(See JPEG image below)
The WiThrottle JMRI webpage states:
302 ¡ª programmer busyThe command station has reported
that it's busy doing something else, and can't do any
programming right now.This usually means that some
other part of the DCC system is doing a programming
operation, e.g. a hand-held throttle.Some DCC systems
can't do ops-mode programming (programming on the
main) while also using the service mode programming
track, in which case they'll return this error
message.
I'm not doing any programming anywhere else on the
layout.______________________
2. The WiThrottle will not allow me to change
addresses.After entering address the address is
displayed in "Recents." Once I've programmed an
address, in this case 6035, when I try to enter the
address a second time I get the prompt: "Loco 6035(L)
In-Use Would you like to acquire this address?" When I
click the YES button nothing happens, even with
repeated pressing. When I click the NO button the
window disappears, but the cycle repeats and remains
NOT SET. I tried to delete the Roster addresses, It's
like the WiThrottle gets "stuck."I also get the prompt
"Unable to load JMRI WebServer page." It appears that
the WiThrottle is not "seeing" the the server" (my
MacBook Pro).See JPEG graphic below.
The PanelPro appears to "see" the WiThrottle in the
"Advertising WiThrottle" window, but no device is
showing the the Device Name window. The DecoderPro
doesn't "see" the WiThrottle in the "Advertising
WiThrottle" window, and no device is showing the the
Device Name window. See JPEG graphics in photo section
under WiThrottle and JMRI Questions.
I suspect these issues may be connected and may have
to do with the drivers.
PLEASE ADVISE,Regards,Robert Diepenbrock
