开云体育

If you have double checked the setup in the manual and it still doesn't work I would check continuity on all the wires from the plug all the way to the inside of your tuner. Search for the pin out of

Hi all, I am Deon ZS6RFI from South Africa. I seem to have a problem to get my AH$ tuner working on my IC7000. Is there any specific tricks to set up the tuner menus and so on I have tried some of the

I'm working from memory (which is unreliable), but here's something to explore: The IC-7000 may have a feature called "Voice Squelch".? It's unrelated to "RF Squelch", which is sensitive to signal

Thanks for all the suggestions. I will check the VSC first, I thought I did eliminate that but I will double check. The radio does not have the head remoted yet, that's a little later. Need to get my

I'm wondering if your voice squelch was activated. Look on the right side, I think, for a button labeled VSC. also look for that in the display. My 7000 is in my truck and I'm inside, so I'm shooting

Check the Voice Squelch Control (VSC) function on manual page 82 (PDF page 91). Steve, W3AHL

Doug, Make sure that the Voice Squelch Control circuit is turned OFF. See if your display says "VSC" on it and if it does turn it off. I think it's page 84 of the manual. I run my RF Gain/Squelch set

Doug, I had a similar issue with mine, and I discovered by accident when preparing to install the radio in my vehicle, that the audio jack on the side of the head unit had bad solder joint

Hi all, I ran my IC-7000 for field day and rediscovered an old issue (I don't use it that often but plan to install it in my truck soon). I had the audio keep cutting out on receive on SSB on all

Thanks Steve for that information and link, a great help. 73 de Geoff vk3sq

Steve W3AHL, I’ve been following this thread because I’ve had the same problem with a used IC7000 I bought several years ago. I bought a replacement mic (off of eBay, which was probably stupid)

I tried back mic jack....very weird...works better but only if I turn vox on... I am really confused by the issue and if it is hardware of software related, I didn't have time to torture shoot too

The original PTT switch used in the HM-151 mic'swas not sealed and had a cheap actuator design.? Icom started shipping a better sealed switch for repair parts in 2007 I think.? It was an ALPS

Very common issue is the momentary switch inside the mic fails.. If you open the mic and press the button hard it should TX. Lots of folks that do the mic mod replace the switch as well.. (I have

Have you tried both mic jacks? Thank You Paul W. Hansen, W6XA Amateur Radio Service 2134 Carthage Road Tucker, GA 30084 (864) 222-3539 www.amateurradioservice.com Sent: Friday, June

Have you tried it into a dummy load? That is what I would try first, just to make sure you don't have an RF problem. And the 7000 has two mike jacks, one on the control head and one on the back of

Ok, so I thought I had a mic issue, no tx when I press the button, grabbed mic from another icom vhf seemed to work fine a few months. Fast forward now, no tx on any mic. Can tune auto tuner fine, so

Hi Paul, Thank you so much! Somehow I had deleted all the asterisks, Added them back and it now works fine. 73, Craig W6ADV Sent: Friday, June 25, 2021 6:04 AM To:

Have you set the Select flag in the channels you want to scan (use SEL on screen S2, * appears next to Memo number) and before pressing SCN to scan only Selected channels? For controlling and setting

Hello Rupert, Thursday, June 24, 2021, 11:09:25 PM, you wrote: Same problem but on all bands... -- Best regards, Zdravko mailto:e77ar@...