开云体育

If you notice replies that seem out of order or duplicate something already sugested, my last post took four days to eventually show up in the Group. It was made via the web interface, not e-mail.

TNC = DATA Leave the ACC for none data uses… Perry K4PWO Sent: Tuesday, January 30, 2018 6:34 PM To: ic7000@... Subject: RE: [IC-7000] Accessory DIN Socket It enables

The DATA port does not have a 12V OP so you still end up using the ACC port to power your interface so you end up using 2 sockets instead of just one one. Roger, GW4HZA.

It enables connection to external equipment such as a TNC, a linear amplifier PW1 an automatic antenna tuner etc. Ken GW0RHC Sent: 30 January 2018 01:24 To: ic7000@... Subject:

Why are you guys using the 13-pin ACC connector for digital modes instead of the 6-pin Data connector? If you use the Data connector you don’t have to worry about mike audio screwing up your digital

Hope this helps its an ICOM stock OPC-599 Adaptor Cable 13-Pin, ACC connector to 7 Pin + 8 Pin ACC Connector. I have used it on my ICOM 7000 73 Ken GW0RHC/HZ1GW/A92HC Sent: 28 January 2018

I run an amp and a SCS PTC II Pro pactor modem with a Mod2 Robust packetcard.? The amp uses an Ameritron ARB704 and of course the 13 pin ACC alsoconnects from the IC7000 to the modem. ?Ialso run an

Hope this helps its an ICOM stock OPC-599 Adaptor Cable 13-Pin, ACC connector to 7 Pin + 8 Pin ACC Connector. I have used it on my ICOM 7000 73 Ken GW0RHC/HZ1GW/A92HC Sent: 28 January 2018

Icom makes a split pigtail that goes from a 13 pin din to a 7 pin and 6 pin female din. I believe it may show in your manual on the 7K 73 Van WD6FGB Sent: Sunday, January 28, 2018 2:39 PM To:

Good Evening Brian Et al: I think that I probably was less than clear in my request for assistance. The ICOM AT-500 auto-tuner isn't the issue. I've fabricated a cable between the rig and the

As far as I know, Dave, it is not possible to run the 7000 without the control head. There’s no way to power up the body and it requires communications with the head. I guess somebody stole your

https://www.universal-radio.com/catalog/hamtune/at500dia.jpg Sent: Sunday, January 28, 2018 8:57 AM To: ic7000@... Subject: [IC-7000] Re: Accessory DIN Socket Good Morning

Hello... Is it possible to operate a IC-7000 base unit with the CT-17 and pc WITHOUT having a control head? if so how? Anyone need another base unit? ty Dave WN4AFP

The DATA port is the preferred interface for digital modes, which would free up the ACC port for other uses. How will not using the ACC port for digital eliminate the ability to auto log? That

Good Morning Brian: The amplifiers in question are: Collins 30L1 ICOM IC-2KL The tuner is: ICOM AT-500 It's not a question of having the appropriate cables and jumpers, I have

What tuner and amp are you using would help Sent: Saturday, January 27, 2018 7:01 PM To: ic7000@... Subject: [IC-7000] Accessory DIN Socket Good Afternoon Group: I recently

Good Afternoon Group: I recently acquired a linear amplifier and was pondering over how to hook it up, the ACC socket is where I have my computer and digital comms programs currently running.

Sounds like you got an attempted click through payload malware/phishing/spam message. Luckily this group strips attachments. Unless you are expecting the message, NEVER click on any attachments,

There is nothing attached?? Joe K2S

Mark, Yes I tried them today and Yes I can tune it from the buttons on the Mike. Joe