Re: Tune button
Assuming you have the 993 interface cable in the 7k 4 pin tuner port,? there does seem to be a problem with some radios - my 993 tuner worked fine with a 706, but the same cable did not work with the
By
Norm Stewart
·
#39923
·
|
Re: Tune button
I have the same setup. When tuning stops, it is usually caused by the #1 wire breaking at the molex connector. If you have a tool for removing molex pins, you can solder in a jumper
Since mine is a
By
James Johnston <jimthej@...>
·
#39922
·
|
Re: Tune button
Hi Paul,
thank you for your answer.
My 7000 is connected to the radio interface of the 993B using an original MFJ-5123I cable.
Please also note that when I push the tune button on the 7000, the
By
MARCO EVANGELISTA
·
#39921
·
Edited
|
Re: Tune button
The 933B by itself is only going to sense RF. You won¡¯t have control of it without the MFJ-5123I interface cable. What you are seeing is normal without the interface cable.
Thank you,
Paul
By
Paul Hansen
·
#39920
·
|
Tune button
Hello,
my 7000 is connected to the radio port of a MFJ-993B tuner.
Unfortunately, the tune button on the 7000 does not trigger the low power keying of the transmitter. The TUNE message on the display
By
MARCO EVANGELISTA
·
#39919
·
|
Re: My IC7000 no workin at 50 mhz and uhf
I don't see any obvious signals or IC that might cause the problem.? If it were my radio I would remove the Logic board from its shielded enclosure and inspect the solder joints.? I have seen two
By
Steve W3AHL
·
#39918
·
|
Re: CI-V Problem
Are you using a UBS-to-serial adapter? If so, make sure that the COM port
number hasn't changed. If it has, change HRD or the assigned port so that
they match.
Windows may have updated the driver
By
Kevin Grantham - N5KRG
·
#39917
·
|
Re: CI-V Problem
Dave,
It looks like you damaged the CI-V port somehow. I always
recommend avoiding hot switching the port by making all connections while
the radio is turned off. I even like the
By
Paul Hansen
·
#39916
·
|
CI-V Problem
Group,
I've recently lost the ability to communicate between my 7000 and HRD using
the RTS-01 cable. I checked the voltage on the CI-V and have about 2.5v. An
Icom rep tells me that is where it's
By
Dave Sheppard W2PAX
·
#39915
·
|
Re: My IC7000 no workin at 50 mhz and uhf
I have similar problems, i found my 6mtr-vhf-uhf antennas are too close to my radio desk and rf trips the 12 volt supply. Antennas about 10 ft away on roof of shack. Try with reduced power or dummy
By
John Rupprecht K3NOQ
·
#39914
·
|
Re: My IC7000 no workin at 50 mhz and uhf
For a bottle of wine I give the following advice:
Open the unit and remove and reseat the CPU box.
This flat tin can on top, fastened with 2 screws only.
If the error remains do the obvious,
wiggle
By
Helmut Wabnig
·
#39913
·
|
Re: My IC7000 no workin at 50 mhz and uhf
Hello Steve thank you for answering me,
I answer with the same sequence of your questions:
the details visible when it stops working are black screen and a continuous whistle and everything is
By
pub1969@...
·
#39912
·
|
Re: My IC7000 no workin at 50 mhz and uhf
What are the visible symptom details when it "stops working and crashes"?? Is the display panel blank?? If you switch to a programmed memory channel in the 6M band instead of using the UP band
By
Steve W3AHL
·
#39911
·
|
My IC7000 no workin at 50 mhz and uhf
Hi Jim, my ic7000 has problems, when I change band with the up or down button and step from the bands hf to vhf it stops working and crashes. Switching from 29.999 mhz to 30 mhz the monitor goes off
By
pub1969@...
·
#39910
·
|
Re: PTT switch source ?
Thanks John
73-
W1JCW
John
Sent: Tuesday, July 17, 2018 12:33 PM
To: [email protected]
Subject: Re: [ic7000] PTT switch source ?
Hi John,
You can purchase the exact replacement from icom at the
By
W1JCW
·
#39909
·
|
Re: PTT switch source ?
73-
W1JCW
John
Sent: Tuesday, July 17, 2018 10:42 PM
To: [email protected]
Subject: Re: [ic7000] PTT switch source ?
I had the same thing fail on my 7000 mic. I found the OEM part # but nobody had
By
W1JCW
·
#39908
·
|
Re: PTT switch source ?
The switches are available in the US from mouser.com.? Search on their web site for?SKQJLBA010? .? That is the exact ALPS switch that Icom ships as a replacement part.? It is a different model
By
Steve W3AHL
·
#39907
·
|
Re: PTT switch source ?
I had the same thing fail on my 7000 mic. I found the OEM part # but nobody had them in stock, or had a long lead time with large minimum order.
I found a similar part that has the same package and
By
Stephen Nelson
·
#39906
·
|
Re: PTT switch source ?
Hi John,
You can purchase the exact replacement from icom at the following URL: http://www.icomamerica.com/en/contact-parts-department.aspx
Just fill out the form and e-mail it to Icom, and they
By
[email protected]
·
#39905
·
|
PTT switch source Part # and source
Digi-Key (450-1804-ND).
73-
W1JCW
John
Sent: Tuesday, July 17, 2018 8:24 AM
To: [email protected]
Subject: [ic7000] PTT switch source ?
Looking to replace the PTT switch on my HM 151.
Does
By
W1JCW
·
#39904
·
|