开云体育

----- Original Message -----
From: Ken & Dianne Godfrey
To: hammond_zone@...
Sent: Monday, March 11, 2002 5:51 PM
Subject: RE: [hammond_zone] Re: Tone Geneator Theory of Operation.


And here I've spent the last two weeks combing electronics parts houses for
dingle arms & flux capacitors! Guess I'll have to throw away all the ones
I've found, since they don't exist.

Thanks a bunch, guys!

BCV-KG

> -----Original Message-----
> From: Randall Bush [mailto:raul_de_jalapeno@...]
> Sent: Tuesday, March 05, 2002 5:42 PM
> To: hammond_zone@...
> Subject: Re: [hammond_zone] Re: Tone Geneator Theory of Operation.
>
>
> OK, guys, I'll take the fall on this one...Gandert, Doug and I
> were pulling
> the provebial leg with each other. Ignore everything we said about dingle
> arms and udatulator plates. This was all in fun and play with words. So,
> your Hammond's OK, Gandert. I also wish to apologize to any
> others who took
> us seriously.
>
> Raul
>
>
> >From: "Gandert De Boo" <bottomline@...>
> >Reply-To: hammond_zone@...
> >To: <hammond_zone@...>
> >Subject: Re: [hammond_zone] Re: Tone Geneator Theory of Operation.
> >Date: Mon, 4 Mar 2002 20:34:27 +0100
> >
> >Hi zoners,
> >
> >Maybe my imagination is to little, but how does this 'dingle arm' look?
> >Where can I find it? My L100 is from 1969/1970. Does it have one at all?
> >And what's to be done with it?
> >I knbow a lot of questions, but I'm still learnig, you know.
> >
> >Gandert
> > ----- Original Message -----
> > From: dug5037
> > To: hammond_zone@...
> > Sent: Friday, March 01, 2002 5:17 PM
> > Subject: [hammond_zone] Re: Tone Geneator Theory of Operation.
> >
> >
> > --- In hammond_zone@y..., "Raul de Jalapeno" <raul_de_jalapeno@h...>
> > wrote:
> > > Doug:
> > > A special tool is required to remove the dingle arm. This is
> > because it's buried under the lower udatulator plate. This tool,
> > which was Hammon part # B2-02T564, consisted of a stratifed pentagrid
> > plate modulator that would maintain the algebraic relationship of the
> > generator coil flux to the magnetic field set up by the nofer
> > trunnions. With this relationship maintained, the dingle arm can be
> > withdrawn through the fennel orifice with out fear of excessive skor
> > motion.
> >
> > Good News--I found the dingle arm under the plate just as you said
> > and I bent it slightly while playing a C AUG chord on the upper
> > manual with all the drawbars out--I could hear the growl increase as
> > I bent it--I stopped at exactly 15 degrees 30 minutes as measured
> > with a laser refractor doo-hickey otoscope. This is the optimum
> > setting for just enough growl and mininum distortion. Be aware that
> > bending to far will raise the emitter levels of the two torsional
> > bias transistors to a dangerous level and could result in a complete
> > meltdown. As with any modification--"your results will vary"
> >
> > Doug
> > T582 with a bent dingle that now sounds like a B3
> > Ain't this fun?
> > BTW I got a piezo tweeter with dual drivers in one rectangle horn
> > housing that I am going to wire into my Homemade Leslie to bring out
> > the key click and sharpen up the percussion--I will not stop until my
> > ears start to bleed!
> >
> >
> > Yahoo! Groups Sponsor
> > ADVERTISEMENT
> >
> >
> >
> >
> > Visit The Hammond Zone
> >
> >
> > To unsubscribe from this group, send an email to:
> > hammond_zone-unsubscribe@...
> >
> >
> >
> > Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.
> >
> >
> >
> >
> >
>
>
> _________________________________________________________________
> Chat with friends online, try MSN Messenger:
>
>
>
> Visit The Hammond Zone
>
>
> To unsubscribe from this group, send an email to:
> hammond_zone-unsubscribe@...
>
>
>
> Your use of Yahoo! Groups is subject to
>
>


Yahoo! Groups Sponsor
ADVERTISEMENT




Visit The Hammond Zone


To unsubscribe from this group, send an email to:
hammond_zone-unsubscribe@...



Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.