¿ªÔÆÌåÓý

Just reporting back: The rolled up tape idea didn't work for me -- tried many times with two different types of very sticky tape. However, the hot needle idea worked on the first

I'm thinking about making a simple rectangular battery tray out of either sheet metal or polycarbonate to go under the radio and attached with the lower cover screws. I know such a design would hold

The original battery charger is listed as NLA. They do have this listed as a substitute. 1.15US $ 8% OFF|Tielong 3s 12v 18650 10a Bms Charger Li-ion Lithium Battery Protection Board Circuit Board

Steve, ??? I used treatstock.com to find someone local with a 3d printer to print the case. It's a pretty good service. There is a learning curve as to what is involved with 3d printing. I would

Can you send the stl file? Have a great day!

Watch the recordings Beginner's Guide to HF Operation- Week 3 recording- https://youtu.be/eG3kFbCZEM8 [image: hf-week-3.png] Watch previous... Week 1 - https://youtu.be/cjZZjfKYPak or Week 2-

From the graphs I've studied it seems like 9.0 volts is more realistic for a 100% discharge, both for the battery and for the radio. On that basis I would consider it to be ideal.? ?Ymmv, fwiw,

I had a question regarding this 3 cell Li-ION pack with the 3d printed chassis and cover. With a 12.4V peak, 11V nominal, and 8.25-7.5V cutoff voltage how well does this work with the 817? Does it

Ok Steve, I will slicing the .stl files and heat up the printer to try print it. We will see¡­ Petr

I Have The Cells But do not have the space for a 3d printer Its a Shame That we no longer the large base of FT-817/818 users to get a entrepreneur to produce that "KIT", I Sure Would go for at leas 2

If anybody want to help with 3D print then I can do it. 73 - Petr, OK1RP -- B: http://goo.gl/Fd2JhJ YT: https://urlzs.com/UHNH9 MeWe: https://bit.ly/2HGPoDx MeWe:

I did this with a wire and the power-up sequence remains the same -- LCD black, relay click on the filter board, powers off. I'll add something semi-permanent and see what the voltages look like. b

This is used on transmit - the limit current would probably be quite high >2A. I would not expect it to trigger at 0.5A even if it was active during RX as this is within the normal operating current

I have the ebay aftermarket battery,works fine:ZZcell Battery for Yaesu Vertex FNB-72, FNB-72x, FNB-85, FT-817, FT-817ND | eBay [1] Jon AB9AH "I have always preferred diversions to duties; this

Thanks for the picture Looks Cool John G8EWG [email protected]> wrote:

John, ??? I wound up building this from some spare parts and Aliexpress. So far it seems to be working ok FT-817 battery holder with BMS by ah1102 | | | | | | | | | | | FT-817

Hi! Here is a question that I think I know the answer to but here goes - I've a '817ND bought several years back as a 'shack in the box' for use in a small 'domestic' shack. It has never been used

I've done some of this. * I put in an ammeter in line with power, and as the rig powers up, it gets to just over 0.5A draw before it shuts off.? As I understand it, the op-amp circuit near the power

The finals are straight across the 13.8US (power unswitched), so they might well drag the supply down. If the controller decides the voltage is too low, it will immediately power down. The main power

In an attempt to clean drawers I have this stuff for sale: - Yaesu YF-122S original filter (SSB). Like new, w/box. 120€ - New Inrad 500hz filter boards (no filter) for DIY'ers. Easy way is