开云体育

Hi Mike Did you ask for the PA Board, this is the Wrong Board, it is called a final unit/Board, p/n CB1333005 Dave 2E0DMB [email protected]> wrote:

That 10 volt sag is with a fresh charge apparently. When the battery starts to discharge it will fall below the minimum ft817 minimum. Joe N1KHB? Sent from AOL on Android On Fri, Sep 20, 2024

Bill, Won't the FT-817nd be fine at around 10v? http://www.ka7oei.com/ft817_pwr_opt.html Ken, N2VIP

Well, the plot thickens. I’ve been in contact with both a parts specialist and tech support at Yaesu USA. The parts person, Beatriz, said the parts, (PA board) are available, but she wasn’t sure

Thanks for the info, William. I did a little more research on the HOWEASY 120 watt solar generator. The YouTube channel Operation Camp has an indepth review of the unit. On testing load and

Where to get an HSU277? I have never had good luck contacting Yaesu support. ?I was calling during COVID, so that might have been the issue. They might have some. The HSU277 is very tiny, and I

I have used a Jackery to power my FT-817 and it worked fine and no RFI.? Last Field Day it was too hot to spend an extended time outside so I ran Class 1E and ran a 100 watt transceiver at reduced

The service manual ("Technical Supplement") is in the Files section of this group at /g/ft817/files/FT-817_817ND_FT-818ND_TS_USA_EXP_EU_E137790J.pdf There's a gold mine of information

Has anyone used one of the small, so called, "solar generator" batteries to power the FT-81X series radio in portable operation?? I'm looking at a HOWEASY 120 watt unit.? It is basically a 88

Hi I don't think it is the correct board you neen the final board, Radio world in the united kingdom have stock, have you called yaesu UK, Dave 2E0DMB [email protected]> wrote:

I contacted the company CSY & Son, responsible for Yaesu spare parts in Italy. Currently, only the PA board CB1152005 is available, which is compatible with all 817-818 models. They told me that the

Yaesu, maybe I had a old radio I removed it from Have a look for a equivalent, it's probably nothing special,but as it is on the underside of the board , I would get the correct one or equivalent

Hi, Is there a reliable seller for the HSU277? Regards Lou VK3ALB [email protected]> wrote:

With those symptoms, ?are likely to have an open D3003. It's possible it could be a relay connection or bad solder joint to a coil in the same place. But, D3003 is the usual issue. ?One test is to

Hi This is my post when i found the problem i was having, Hi i found this when my FT817 did not output power on 2m and it was the Diode that had gone bad, Good Luck, Dave 2E0DMB so on Pin 8 of Q3003

Hi if you look up posts from me 2E0DMB you will find the info, I had this problem with a ft817nd and it was a diode On the bottom of the band switching board if I remember correctly This has been

Pietro? I2OIM I have a PDF of the 817 / 817ND? if these would help I can send a copy CharlieKA9HDG

It seems that the FT-818 group is exhausted, so I try here. My 818 has no output on 2 m, while it works on 70cm and HF. The SWR is at maximum, so I think some relay is not closing when it should. Is

As I understand it, the parts they are offering today are FT-818 finals, and they work in FT-817/817nd. This part will be offered by Yaesu as long as they provide support for the FT-818, so likely a

So after the newest information on the finals board, thank you! My 817 is a non ND. Will the replacement board work on a non ND? Has anyone actually replaced the finals board? If so, can it be done at