开云体育

The FTX-1 has a mobile mounting bracket? The FY-817/818 didn't... Are we acting like this is a radio people will be mounting to/under their car dashboards? Is QRP HF Mobile really a thing? Somehow

Exactly ;-) I have seen the required bracket required to keep it in a useable position, not good at all. Who wants to carry that extra junk. Bad bad design. 73 de Andy

Ahh--- being , "Made in Detroit" born and raised, I always loved the speculation every September when the new cars were "unveiled" and come the Detroit Auto Show 1st week of the year, the concept

Exactly, Let apart what it can['t] do; this radio will be fine mounted on its bracket inside a car, or in a cabin table, probably even finer attached to a laptop. Radios with big touchscreens exposed

I think it looks like a good little radio and I’m quite excited about it. The aftermarket will come up with protective rails/cages very quickly, in fact I will probably have detailed measurements

The FT-817/818 was an amazing collection of features and compromises, it's very unlikely it will be repeated any time soon. (As I recall it was a labor of love for one Yaesu Executive, he built the

The form factor as been around since WW2 (WS32 rigs?), Midland Chicken Banders, Yaesu with the original FT290 etc from the early 80's and ending with the FT818. A tried and tested format, easy to

Hello, Have you checked the output of your powersupply under a load? I had one that measured 12.5 volts with no load, but? when I connected to a radio, the output dropped to under 7 volts. I had to

Thanks, Mike. 73….Eric VK2VE. Sent: Saturday, 7 September 2024 18:33 To: [email protected] Subject: Re: [ft817] FT-817 Replacement

Thanks, Steve. I would never have guessed that one. 73….Eric VK2VE. Sent: Friday, 6 September 2024 21:25 To: [email protected] Subject: Re: [ft817] FT-817 Replacement Application Specific

G’day Greg, I wasn’t being particular. You are correct. Steve VK2ARS Sent: Saturday, September 7, 2024 1:18 AM To: [email protected] Subject: Re: [ft817] FT-817 Replacement Application Specific

Application Specific Integrated Circuit, i.e. a custom part as opposed to a generic FPGA (Field Programmable Gate Array) for DSP (Digital Signal Processing), or indeed any custom IC replacing a number

I had the happen to me and got the small ring left in it by heating up a tip of a small safety pin and poking that into the yellow ring and slowly lifting it out off the power pin. Marty kd8bj

Check the power socket on the radio to see if the little yellow insulation tip on the end of the plug has not dislodged and is stuck in there. If that happened from another cable, you won’t be able

You mean disconnect it from battery pack? Sorry I forgot to mention this, I have no battery pack installed (to be honest, I don't have my battery pack anymore). Or pull it from mainboard

Pull the battery connector and try again. -- Al Skierkiewicz WB9UVJ

Hello everyone :) I have recently came back to the ham radio hobby, and decided to remove some dust from my old FT-817 (not ND) To my surprise, the unit refuses to turn on when connected to a 13.8V

I like that it has a more modern chassis. The trend for faceplate on a slab form factors is well established by icom with the 705, elecraft with kx2 and kx3, and the tx-599. So far as features, I

Thank you for saying what _needed_ to be said, Ken! The negativity, shortsightedness, and lack of gratitude around here lately has been increasingly unpleasant. I wish Yaesu all the best with their

Application Specific Integrated Circuit, if we're being particular. Greg KO6TH tomsdad97 via groups.io wrote: Application Specific