开云体育

Stepdown Fitting

#dustcollection

[email protected] All Messages By This Member #114325 My hose is 120 mmn? OD=4.72" almost 4 3/4" The dust collector is 4" OD Who has a setp down fitting of this size either rigid or flexible instructure? Is there a flex one than can be used with hose clamps to tighten the hose to the collector? How do you predetermine a hose clamp size? Is there a rule of thumb/ Thanks Seems simple, but haven't found one yet.
Mike S All Messages By This Member #114326 I went with a wholesale change to an Oneida system a couple of years ago and, while I do have a ceiling duct for a hose for my hand tools at my assembly table, I added a Festool 48AC vac that sits in the vicinity that I find does a much better job. ?Everything is gated and where not permanently attached, (Bandsaw, oscillating sanders, and jointer all have to be mobile) I share a hose and use this system with some success: ? Mike
imran All Messages By This Member #114327 开云体育 This showed up on search I use 5” hose on 120mm port. To increase 120mm port OD I wrap a strip of foam (like used to wrap items for shipping). This has worked fine on KF saw port as there is nothing tugging at it to cause any issues. I am not aware of a rule of thumb for hose clamps. I just make sure that the range is accommodating. BTW, the clamps with a step for hose coil are supposedly best but I have not used them. For std hose clamps the generic are junk and I found ones I ordered from Felder much more robust. I found these similar to what Felder supplied at a lower cost. Imran? toggle quoted message Show quoted text On Feb 17, 2021, at 10:09 AM, fx77@... wrote: ?My hose is 120 mmn? OD=4.72" almost 4 3/4" The dust collector is 4" OD Who has a setp down fitting of this size either rigid or flexible instructure? Is there a flex one than can be used with hose clamps to tighten the hose to the collector? How do you predetermine a hose clamp size? Is there a rule of thumb/ Thanks Seems simple, but haven't found one yet.
imran All Messages By This Member #114331 开云体育 Oh! i got those hose clamps from Hose clamp king Also, I shared my solution for 120mm port in case that is appropriate for you case. If so then you can just use a 4” to 5” adapter at your DC. That would be much cheaper than oneida option. Imran toggle quoted message Show quoted text On Feb 17, 2021, at 10:55 AM, imranindiana via groups.io <imranindiana@...> wrote: ? This showed up on search I use 5” hose on 120mm port. To increase 120mm port OD I wrap a strip of foam (like used to wrap items for shipping). This has worked fine on KF saw port as there is nothing tugging at it to cause any issues. I am not aware of a rule of thumb for hose clamps. I just make sure that the range is accommodating. BTW, the clamps with a step for hose coil are supposedly best but I have not used them. For std hose clamps the generic are junk and I found ones I ordered from Felder much more robust. I found these similar to what Felder supplied at a lower cost. <image0.png> Imran? On Feb 17, 2021, at 10:09 AM, fx77@... wrote: ?My hose is 120 mmn? OD=4.72" almost 4 3/4" The dust collector is 4" OD Who has a setp down fitting of this size either rigid or flexible instructure? Is there a flex one than can be used with hose clamps to tighten the hose to the collector? How do you predetermine a hose clamp size? Is there a rule of thumb/ Thanks Seems simple, but haven't found one yet.
Jarrett Maxwell All Messages By This Member #114332 I have been using these wire clamps which bridge over the helical wires in the dust collection hose.? Jarrett Maxwell? toggle quoted message Show quoted text On Wed, Feb 17, 2021, 10:15 AM imranindiana via <imranindiana=[email protected]> wrote: Oh! i got those hose clamps from Hose clamp king Also, I shared my solution for 120mm port in case that is appropriate for you case. If so then you can just use a 4” to 5” adapter at your DC. That would be much cheaper than oneida option. Imran On Feb 17, 2021, at 10:55 AM, imranindiana via <imranindiana=[email protected]> wrote: ? This showed up on search I use 5” hose on 120mm port. To increase 120mm port OD I wrap a strip of foam (like used to wrap items for shipping). This has worked fine on KF saw port as there is nothing tugging at it to cause any issues. I am not aware of a rule of thumb for hose clamps. I just make sure that the range is accommodating. BTW, the clamps with a step for hose coil are supposedly best but I have not used them. For std hose clamps the generic are junk and I found ones I ordered from Felder much more robust. I found these similar to what Felder supplied at a lower cost. <image0.png> Imran? On Feb 17, 2021, at 10:09 AM, fx77@... wrote: ?My hose is 120 mmn? OD=4.72" almost 4 3/4" The dust collector is 4" OD Who has a setp down fitting of this size either rigid or flexible instructure? Is there a flex one than can be used with hose clamps to tighten the hose to the collector? How do you predetermine a hose clamp size? Is there a rule of thumb/ Thanks Seems simple, but haven't found one yet.
Jeff All Messages By This Member #114340 I posted a 3D design you can print or customize to your need.??/g/felderownersgroup/files/3D%20Printer%20Files/120mm%20to%204%20inch%20quick%20connect%20adapter.zip

Previous Topic Next Topic