Re: Parts list for Jointer guard arm
Hi Lucky,
What you shared looks like my booklet but it does not include the arm to which the guard is mounted. The guard itself is included on a separate page. Kind of strange to not include this.
toggle quoted message
Show quoted text
On Nov 7, 2024, at 5:31?PM, David Luckensmeyer via groups.io <david@...> wrote: ?
Hi Imran:
?
Does this help?
?
Warm regards,
Lucky
?
Dr David Luckensmeyer
Designer & Maker
@luckensmeyer
M: 0413 013 115
?
My book for Dual 51 does not include the parts list for the spring loaded arm that has the cutterhead guard. See pic below:
There is a bracket (has been removed in above pic) that mounts under the elevation knob and I would like to have the typical assembly drawing and part numbers if anyone has them.
<Dual 51 Extract.jpg>
|
Re: Parts list for Jointer guard arm
Hi Imran:
?
Does this help?
?
Warm regards,
Lucky
?
Dr David Luckensmeyer
Designer & Maker
@luckensmeyer
M: 0413 013 115
?
My book for Dual 51 does not include the parts list for the spring loaded arm that has the cutterhead guard. See pic below:
There is a bracket (has been removed in above pic) that mounts under the elevation knob and I would like to have the typical assembly drawing and part numbers if anyone has them.
|
Parts list for Jointer guard arm
My book for Dual 51 does not include the parts list for the spring loaded arm that has the cutterhead guard. See pic below:
There is a bracket (has been removed in above pic) that mounts under the elevation knob and I would like to have the typical assembly drawing and part numbers if anyone has them.
|
Re: OT: What is the name of this type of clip?
That type of fastner? were more commonly used in car upholstery See
?
https://www.springmasters.com/push-on-fasteners/
--
Paul Mc Cann
|
Re: OT: What is the name of this type of clip?
Shaft Clips, 15-7 PH Stainless Steel, for 1/8" OD https://www.mcmaster.com/97622A102
If you can sharpen in place, that¡¯s what I do. Just a good file will do or is jason suggested Diamond stone water lubricant Designing and building for 50 years
toggle quoted message
Show quoted text
On Nov 7, 2024, at 7:30?AM, Jason Holtz via groups.io <jholtzy@...> wrote:
? Michael, I'd forget trying to remove that thing and just use a small diamond stone to do those edges. Jason Holtz
J. Holtz Furniture
3307 Snelling Ave. South Minneapolis, MN 55406
612 432-2765 -- Jason J. Holtz Furniture 3307 Snelling Ave. South Minneapolis, MN 55406
|
Re: F700Z Slider Transport Locks / Lugs
I have removed Oh easily a couple hundred of these and all I do is push on the slider one way or the other in till they loosen take it out Designing and building for 50 years
toggle quoted message
Show quoted text
On Nov 7, 2024, at 8:43?AM, KRPatel via groups.io <kamalsonal@...> wrote:
? Had the same issue with my K700S and F700Z as they were set in place very snug.? I used a pair of pliers and slowly worked them out...keep in mind there may be thin strips of wood also inserted to prevent the slider from moving...peer down the long channel and check and if you have a PhD in hieroglyphics there may have been a separate set of instructions/paperwork that illustrates the removal of these if you can decipher.
?
Kamal Patel
|
Re: F700Z Slider Transport Locks / Lugs
Had the same issue with my K700S and F700Z as they were set in place very snug.? I used a pair of pliers and slowly worked them out...keep in mind there may be thin strips of wood also inserted to prevent the slider from moving...peer down the long channel and check and if you have a PhD in hieroglyphics there may have been a separate set of instructions/paperwork that illustrates the removal of these if you can decipher.
?
Kamal Patel
|
Re: OT: What is the name of this type of clip?
Michael, I'd forget trying to remove that thing and just use a small diamond stone to do those edges. Jason Holtz
J. Holtz Furniture
3307 Snelling Ave. South Minneapolis, MN 55406
612 432-2765 -- Jason J. Holtz Furniture 3307 Snelling Ave. South Minneapolis, MN 55406
|
Re: In Need of New Tires for F38
Ron,
?
I just put new wheels from Western Roller on my F38. ? They fit perfectly and work great. ?
?
My original wheels seemed to be in flawless condition and were still soft and pliable. ? ?However, they did not work well at all. ?
?
Western Roller item number 1040-0020013. ? 120mm X 60mm tapered ID for split hubs. ? 70 Duro. ??
?
?
-Rusty
|
Re: F700Z Slider Transport Locks / Lugs
I should mention that if you do try to use my method, make sure the slider locking lever is not engaged!
On Thu, 7 Nov 2024 at 09:14, Mi?elis Vindavs via <mikelis.vindavs= [email protected]> wrote: I had a similar issue. Trying to remove them using tools it felt like I'm going to slip and damage something. What worked for me was giving the sliding table a sharp push which made the lug on one side pop out.
Hope this helps, and congrats on the new machine!
On Thu, 7 Nov 2024 at 04:51, imranindiana via <imranindiana= [email protected]> wrote: The only help I can offer is to confirm that they are for transportation. ? My new F700Z arrived today.? The table was shipped with transport locks / lugs. Seems like the factory hammered them in pretty hard and I cannot seem to be able to remove easily. Anyone else had this problem? I am assuming these are the transport lugs. ?
?
<IMG_6943.jpeg> <IMG_6944.jpeg>
|
Re: F700Z Slider Transport Locks / Lugs
I had a similar issue. Trying to remove them using tools it felt like I'm going to slip and damage something. What worked for me was giving the sliding table a sharp push which made the lug on one side pop out.
Hope this helps, and congrats on the new machine!
On Thu, 7 Nov 2024 at 04:51, imranindiana via <imranindiana= [email protected]> wrote: The only help I can offer is to confirm that they are for transportation. ? My new F700Z arrived today.? The table was shipped with transport locks / lugs. Seems like the factory hammered them in pretty hard and I cannot seem to be able to remove easily. Anyone else had this problem? I am assuming these are the transport lugs. ?
?
<IMG_6943.jpeg> <IMG_6944.jpeg>
|
Re: In Need of New Tires for F38
Hi Ron,
If you tried to scuff by hand you may not have removed enough material. You literally have to remove the outer layer of material. When I did it before having them recovered, I glued the multiple sandpapers slightly wider than the wheels on a board. The sandpaper strip was long enough to cover length of 4 wheels, well in my case. I clamped the board to the table/slider and lowered the running PF onto the sandpaper. You should see some rubber coming off. With new surface the grip will improve but best long term solution is to get them recovered with polyurethane.
toggle quoted message
Show quoted text
On Nov 6, 2024, at 9:31?PM, Ron Corselli via groups.io <rcorselli@...> wrote: ? I did take some 60 grit paper to them but, sadly, didn't help much.
|
Re: F700Z Slider Transport Locks / Lugs
The only help I can offer is to confirm that they are for transportation.
toggle quoted message
Show quoted text
On Nov 6, 2024, at 8:46?PM, John Deming via groups.io <jldjr26@...> wrote: ? My new F700Z arrived today. ?The table was shipped with transport locks / lugs. Seems like the factory hammered them in pretty hard and I cannot seem to be able to remove easily. Anyone else had this problem? I am assuming these are the transport lugs. ?
?
<IMG_6943.jpeg> <IMG_6944.jpeg>
|
Re: In Need of New Tires for F38
Thanks for that info, David.? I'll check with each.
|
Re: In Need of New Tires for F38
I did take some 60 grit paper to them but, sadly, didn't help much.
|
F700Z Slider Transport Locks / Lugs
My new F700Z arrived today. ?The table was shipped with transport locks / lugs. Seems like the factory hammered them in pretty hard and I cannot seem to be able to remove easily. Anyone else had this problem? I am assuming these are the transport lugs. ?
?
|
Re: OT: What is the name of this type of clip?
Thank you sir!? That was what I needed.?
STARLOCK WASHER .?
In my experience, not typically reusable, destroy upon removal and replace.?
On Wed, Nov 6, 2024 at 4:15?PM Michael Garrison Stuber via <mtgstuber= [email protected]> wrote: It's not a snap ring / circlip.? Here is a closer picture.?
I cannot make out the clip in your photo. Google ¡°circlip¡± and see if that is what you are dealing with. ? Get a snap ring plier set with different sizes of tips. Not expensive and available at places like Home Depot, and really handy to have around. -- John Hinman
Boise ID
K700S and A941
-- Brett Wissel Saint Louis Restoration 1831 S Kingshighway Blvd (at Shaw Blvd) St Louis, MO 63110 314.772.2167 brett@...
|
Re: OT: What is the name of this type of clip?
STARLOCK WASHER .?
In my experience, not typically reusable, destroy upon removal and replace.? On Wed, Nov 6, 2024 at 4:15?PM Michael Garrison Stuber via <mtgstuber= [email protected]> wrote:
It's not a snap ring / circlip.? Here is a closer picture.?
I cannot make out the clip in your photo. Google ¡°circlip¡± and see if that is what you are dealing with. ? Get a snap ring plier set with different sizes of tips. Not expensive and available at places like Home Depot, and really handy to have around. -- John Hinman
Boise ID
K700S and A941
-- Brett Wissel Saint Louis Restoration 1831 S Kingshighway Blvd (at Shaw Blvd) St Louis, MO 63110 314.772.2167 brett@...
|
Re: OT: What is the name of this type of clip?
It's not a snap ring / circlip.? Here is a closer picture.?
I cannot make out the clip in your photo. Google ¡°circlip¡± and see if that is what you are dealing with. ? Get a snap ring plier set with different sizes of tips. Not expensive and available at places like Home Depot, and really handy to have around. -- John Hinman
Boise ID
K700S and A941
|
Re: OT: What is the name of this type of clip?
I have several snap ring pliers.? ?The issue for me is that it isn't a snap ring.? ?It completely surrounds the pin and has six spring steel tabs that hold it in place.? ?When I've removed these in the past from motor shafts,? I've damaged them.?
to remove the cir-clip you i thing you want snap ring pliers. the internal and external type and different sizes depending on the clip in question.
|
imran
David Luckensmeyer
Jason Holtz
