开云体育

Hi Imran, That auction closed today. I picked up the 4x8 lift table, disc sander and forklift. Now just have to get them home during in what is shaping up to be really poor weather. The wide belt

I have a 2011 model year Quincy QT-54 single phase 5HP 220v vertical tank model running on a 20 amp circuit without issue. My use case driving the purchase was to run an automotive HVLP spray gun and

This may help answer your questions: https://flic.kr/s/aHskqy4ZAD David Best https://www.flickr.com/photos/davidpbest/albums https://www.instagram.com/davidpbest/

My 2009 KF700SP has separate start circuit relays for the saw and shaper. Sounds like the saw relay is bad. You can jumper the relay to test the rest. I am assuming the wiring is find unless the

The "new" Casadei machines are close enough to pick up. In particular the F25 tilting shaper currently at $4K. Anyone have experience with the brand and if it is worth pursuing even without a sliding

? Mike, This is made by RUWI and some folks here have this setup. I am not sure how long Felder has been selling it though. I would think it should work on your older slider but I will leave that

I understand this is a new item ( https://us.feldershop.com/en-US/en-US/en-US/en-US/Sawing/Accessories/Tensioning-and-clamping-devices/Clamping-and-saw-system-set.html) but would like to know if

Well, I just got word yesterday (yes a Sunday e-mail) that as my AD-941 was delivered on Friday, I will have to wait until June for my KF700SP and HS950. The wait is two months more that I thought.?

Hi Anthony, An auto drain my service you just fine. Mac martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330 cell airtightclamps@... airtightclamps.com

Blast cabinets need a lot of air. How large are the motor and pump? I'd look for a good condition Quincy QR 325 if you need 15 cfm and 5 hp. They are slow running and quiet - for a piston pump -. Dave

Should I be looking at a 3-phase or single phase compressors for the 60-80 gallon size with use of a phase perfect? As suggested by Dave Kumm, I will be using a small pancake style compressor for most

Thanks Dave! This is all a new idea to me so trying to get my head around it. Very much appreciate the idea and the response. Anthony

FYI ...... Imran Begin forwarded message: From: "MachineryMax.Com" <sales@...> Date: January 25, 2021 at 10:51:00 AM EST To: imranindiana@... Subject: Auction closing today! Complete

That looks close to what I have. I haven't looked in a hundred years but that gets you there. I can run both compressors through the dryer but almost never bother with the small Jun Air. I only run

This topic has a long history indicated by the many search results. ?I have read many of the posts and gathered some great ideas. ?Unfortunately, I didn't save the info when browsing previously and

Thanks Jason. I do know someone and will check. I researched and it showed that you can get the markings by running the woodmizer on top of a smooth board but backwards. I tried that on my bandsaw but

Thanks David. I thought that might be the case based upon price of new. Imran

dunno know nuthing? 'bout the Laguna specifically. A start Cap? is out of the loop when the motor is? running.? You engaged it while holding the switch? in the start position then disengaged it

Imran, If you happen to know someone with a woodmizer, they make a blade sharpener that is quite efficient. My buddy just got one, I may have to try it out. Otherwise, we just recycle them. If you

Thanks for the original post and I'm glad your friend is on the mend. I've had some close calls messing with vertical runs of snap lock dust pipe. By design one is reaching out because of the ladder