开云体育

If you wanna make it very economical by tap on branches They attach to the main screw it on or pop rivet. martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330

Hi Michael, Calculations for dust collector setup are not that complicated. Here is one place I looked at 20 yrs ago and they still have the info: Dust Collection Information airhand.com Imran Malik

I'm in a similar position, shopping for a workshop where the construction won't be done until ~May next year.? At least the Phase Perfect units aren't all that big, so getting a delivery now and

Sounds like no one is using metric sized main ducts, which is sort of what I expected to hear.? I'm a little concerned about going from a 160mm inlet to a 7" duct (~175mm), as I don't know how to

Hello. I have a k 740 s for 1 year and we really have fun with it. Congratulations on a good choice. Especially the sliding table "X Roll" does a very good job. It is a great advantage to be able to

The rumor is true that come the new year Phase Technologies are raising their prices and no they won't let you buy one now for delivery in six months when your shop is completed.? I figured how hard

Sounds correct. I have to remove mine as well for the full-size blades. -- Bill Hope ( https://dnisw.com ) -- Measure it with a micrometer, mark it with chalk, cut it with a Hammer

On my C3, I always removed the ZCI before changing blades or scoring unit. If you get a T-handle hex wrench, the T-handle mass spins the ZCI screws out pretty quickly; it doesn't take that long.

Jonny, My B3 is a 2021 unit. I can only guess/suppose that the available space for installing the blade is similar to that of your K3. Even after rotating the scoring saw shield in the proper

My k3 is new to me, but it’s a 2005 model that is in reasonable shape. A 315mm blade does go below the table height, just, but only by a few millimetres. Why is this a problem? If I have a Zero

Congratulations Glen, I just received my K740S a few weeks ago. I pretty much spec'd mined out as far as you can: DRO crosscut, DRO rip (although not motorised) and power drive height and tilt. I also

Hi, New to this group, but have been reading a lot of messages. Mostly around Felder K700S and K740S. Just put down a deposit on a K740S today. Kind of excited about it! It is physically close by at

Jason, I know you have a KF the tilting spindle on it so if you have an analog reader for the tilting spindle then I’d take the diameter divided by how many segments you wanna make and set the angle

Jason, you have certainly piqued our interest with this project. I hope you share progress and solutions as you go! I would guess that the fins between each flute add considerable complexity and

?Hi Jason, I have tried gluing multiple segments several times and can’t say that I have achieved perfect alignment ever. If all segments are perfectly aligned the last one always has a slight

Great to hear from you all, I'm really glad you have found the video helpful. There are definitely things that could be improved upon with the design of this accessory, but i find this a workaround

Michael Fortune used biscuits, stretch film, and clamps to glue the pedestal base in steps. I think Lamello Zeta P2 will absolutely shine in this glue-up. [image: table.jpg] James groups.io

I lay down on inside and use filament packing tape , flip over and glue tapered t g glue joints work best after glueing use band clamps to hold martin/campshure/co/llc mac campshure 7412 elmwood ave.

Thanks Imran, When I have done staved construction for coopered things in the past, I always glue up whatever number of segments can easily be done with bar clamps before it gets squirrly and wants to

I enjoyed the video and thought it was honest from someone who uses it to make a living. I'm thinking about adding that part to mine in the future and found it very helpful! Thanks for all the videos