开云体育

Hi all, I'm currently in the process of making, or more correctly attempting to make, a bandsaw power feeder. It is a bit of an experiment and I'm quite prepared for it not to work, it's mainly been

There is another advantage to the helicoidal steel roller, you can do the quick change with it if you ever wanted to get a rubber one for a particular reason, like running plastics, for instance.?

Rubber feed rollers are a wear item that require replacement over time depending upon use conditions. The photo below illustrates the rubber feed rollers out of my Dual 51 after several years of use.

The problem with rubber rollers is board gets stuck in the roller and it chows it out now you gotta replace it , use spiral roller steel, and won’t have that problem. I suspect that was section and

I am going back to the feed roller. I initially thought the feed roller that comes with the FS7 by default is the rubber roller. In fact, the machine comes by default with helicoidal steel roller.

I dislike WD box store crap Try to avoid compressed cans always have to puncture and drain when propellent is gone. Let alone breathing the VOC I buy lps. 1,2, 3 by gallon And use labeled squirt

P.S. WD40 is also somewhat solvent borne, it will work great immediately, as soon as it dries up a bit you will have a sticky mess with lots of residue. Brian Lambblamb11@...

Dry lubes are generally a solvent that carries a high pressure additive. You coat the items, the solvent evaporates and leaves behind a high pressure "coating" and then that does the rubbing against

Both Slick 50 and WD40 are penetrating oil lubricants.? The LPS 1 is considered a "dry lubricant" / water displacement element.? I think the LPS 1 would be good to treat surfaces that are exposed,

I will definitely look into lubricanting those areas tonight, thanks for the suggestion.

Or lps 1 or slick 50 martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330

Just e-mail Felder with S/N off the machine label ( techsupport-us@... ) and they will provide a soft copy downlink. This ensures you get a manual specific to your model yr. This will

You can buy the manual from Scott & Sargent: https://www.scosarg.com/copy-of-manual-for-felder-kappa-40-panel-saw?srsltid=AfmBOooVIi-GNTdVpNpSZ4fNqPZY8jiv1-m_KBPjhIjRaRh3g9-sHVt7

You need to lubricate the jack rod anywhere it rotates inside another piece with something like oil or WD40.? My stock FAT300S performed very poorly until I did this (it would be difficult to pump

I have to south worths One 4x 6 x 7” to 36” at least 4000# on wheels with 3 wheel lift One 5x8 x 15” to 84” 6000# Both push afoot medal martin/campshure/co/llc mac campshure 7412 elmwood

Southworth? Dave Davies [email protected]> wrote: -- Dave & Marie Davies www.myfinishingtouch.com 318-219-7868

Hi JP, I have a Felder FAT 500S. When loaded with a few hundred pounds of material, it does take some effort to lift. -- Tom Gensmer Heritage Home Renewals, LLC Minneapolis, MN

Hello all, New to the group and the Felder/ Format brands. I am picking up a new to me 2006 Kappa 40 with the motorized height and tild adjustments this weekend and am looking to get more information

Does anyone own both of these? I have the 300S and with a load it takes a fair amount of pressure on the foot pedal to raise the table. With almost twice the weight capacity and dual hydraulic

Robert, I am not geographically located where you are as I am in Michigan. But When I bought my BF631 in 2012, I got a trailer and drove 7+ hours to Milwaukee Wisconsin to get it. Not a big deal. If