开云体育

Thanks Brian. Bandsaw is definitely an option. I am trying to find out if anyone is doing this on shaper or saw. If so, how? Imran Malik https://www.facebook.com/groups/362481112015700/?ref=share

Bandsaw... you can slot as deep as you would like. Cut both sides and the flatten out the bottom of the slot. Brian Lambblamb11@...

Hi Brett, I assume you have more the 4” capability on the saw. Do you slot that high on the saw? I am trying to figure out if I am giving up on this option too quickly, after a few tries. I believe

What type of knife system is on that cutterhead? David Best - via mobile phone

You can run the planer with the jointer tables down, or if you're doing a lot of planing you can flip them up, put the cover on, and do your planing. Then remove cover and put tables back down when

Bandsaw and chisel or sanding block to achieve finished edges where circular blades can't reach. [email protected]> wrote:

Is the planer cover in the 4th image a separate piece that has to be put on and removed to store? martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330 cell

I suspect most of the problems people are seeing with this blade have to do with runout. You need to double check the runout of the saw blade flange and look for any burrs or dings. Then install the

This has been my experience as well. But test the blade as soon as you get it and send it back if it’s leaving saw marks. Felder includes this instruction in the saw package.

I have the AKE version and it cuts super smooth with 4500rpm on my K945s. The funny thing what i've noticed is I've done a cut what may have been a little too much for this blade (8cm thick european

Jason, possibly a little newer according to this link. https://wtp.hoechsmann.com/en/lexikon/8745/panhans_609 Patrick, the saw in my picture is in the Gutmann cladding factory in Germany. I think the

Like-new Omec 750CN dovetail machine. 20" capacity with CNC control for incredible precision and control-ability. Cut traditional dovetails, box joints, sliding French dovetails, etc. at the spacing

- Model AD515 - 2018 - 114 hours on the meter - 515mm (20") cutter head - 8' long tables - 220V - 3PH - Tables do not need to be lifted to use the planer - This machine is basically brand new and

??Hi Mikelis, Can’t take credit for the design, following caught my eye: I should have added that while I can get ~4” cut (never tested it) on KF700 with 300-315 mm blade, I only get 3.3” on

That looks like a cool design for the stepstool. Not sure if this helps any, but Felder makes a slotting/grooving blade in two sizes - 230x4 and 300x5 (03.0.030). It would still require multiple

I came across a step stool design that requires ~4” deep slots. I know there are other ways to achieve the look of an angled bridle joint but these methods require more work. Here is what I would

The beam geometry and bearing configuration on that Panhans looks to be the top of the pile as far as those vintage machines are concerned. Are they more rare than the T17 in the States? They are

Joe, That Panhans looks to be similar vintage to my 684, maybe older? Mine is 1985 according to the machine's tag. Jason Holtz J. Holtz Furniture 3307 Snelling Ave. South Minneapolis, MN 55406

I suspect it is the small size of the gullet that is causing the problem. Because the gullet is so small, it is easy to load it with the chips from the cut. So there are two solutions to not

Aaron, that's a very good theory, and the shape of the teeth and saw marks would support that. The manual that came with the blade emphasized using higher rpm for better results. I'll have to explore