开云体育

I agree that the 12" blades are noisy - my optical tachometer indicates a saw blade speed of 4750 RPM on my KF-7. For a 12" blade that's about 170 MPH! I don't think Unisaws and other cabinet

I just uploaded to the vault in the tech articles section, a diagram showing the proper boring and pinhole spacing for sawblades that go on the Felder machines.This diagram was provided to me when I

Hello Geoff, Great recording, thought I was in my shop! The saw sounds the same as my Felder and other commercial saws I've heard. One thing I have noticed about having a small 200 sq. ft. shop is

Wow - yet again I am thoroughly impressed by the knowledge and interest of those participating in the forum. I haven't checked my e-mail for a few days due to long busy days at work. Let me try to

...got a "file not found" message when I tried the Leading Edge link,,,what's up w/that? -Philip Art Pentz wrote:

Try this, the problem is that the htm has an l after it, should be - html - the line break put the l on the next line - so it is not part of the line. http://www.theleadedge.com/ this will work -

...Ballew Saw and Tool, 1-800 CUT-RITE, has been a great source for tooling and consumables - all kinds of shaper cutters, Mirka sandpaper, some machinery - good prices, super service. No affiliation

Rod, Sorry I didn't have a chance to reply until tonight. Feel free to give me a call when you get in to Bellevue. I'm in Everett, about 30 minutes north of Bellevue, or 15 minutes north of

A quick reminder to the group: to place your vote in the shaper cutter poll, please visit the following web site: http://www.egroups.com/vote?id=953872295171&listname=felder-woodworking There is no

Thanks for the tip on the Freud groovers, Art. I have been perusing a Freud catalog and have had my eye on those groovers, especially the 1/4 & 3/8" x 6" OD or the 8" OD. I have checked "Abbey Tool"

With respect to the current poll on cutter brands I thought I would mention that the best prices w/ delivery on Freud shaper cutters I have found are from "The Leading Edge"

Felder

What brand of shaper cutters do you prefer to use on your Felder? Have you found any particular good values among the various brands available? What would be your top 3 choices for the

Geoff, I believe you said you live north of Seattle but I'm not sure. Tried to look your location up under the member info but must not be doing it correctly. Anyway, I have to be in Bellevue this

The kerf is 1/16 of an inch - I checked it with a caliper, it it exactly 1/16. Cuts great!

Joe, for cutting panels with the 100mm scoring blade I'm limited to a ten inch blade. I switch regularly between the rebored Forrests which are 10inch and the 300 and 315 blades I have from Felder.

John, Are you running a 10" or 12" blade on your machine? I would imagine that the dB levels specified by Felder for noise levels are measured with the 10" (250 mm?)blades. Joe "john renzetti"

Geoff; Wow, 98dB is loud -- maybe loud enough to get a visit from OSHA or the FAA. I think a jet at full-throttle is just a bit over 100 dB! Does the value change depending upon the position of

Wow...98dB is loud. I do not have a sound meter, but I can't imagine that the saw on my machine is 18 dB louder than the planer. If the sound meter computes dBA, perhaps the higher pitch of the air

John! Hate to ruin a good tale, but I did pull every accessory off the BF-5 before lifting it off the truck solo, so it probably wasn't any more than a ton - hardly worth mentioning! Besides, this