开云体育

John, You can take a look at the plug you have, it can be a good start, it you have 4 wires it defensively don't use natural. If you have 5 wires, it still not guarantee the natural is used at all.

Imran, The new PP units don't use natural wire as well. only 230V + ground.

In addition to what Imran wrote, Felder is generally an EU company, and the machines are expected to usually work with EU voltage. The voltage between a phase and the natural in EU is 230V. so if

FWIW my 2023 10kw Format4 profil z x-motion doesn't use a neutral. I'm not sure if the same motors and electronics are shared between their shapers and saws or not. [email protected]> wrote:

How do I confirm? The saw in question is a new Format4 KAPPA 450 X-motion. -- John Hinman Boise ID K700S and A941

I was curious about my old PP unit. The manual does not show a connection for the neutral. Not sure if same is true for the newer models. Neutral is not needed by the PP to produce 3 phase but it

It is a valid question. A 3 phase machine can have a 120V single phase load and for that neutral would be required. I am not aware of any Felder saws that require neutral. Imran Malik

I contacted an electrician to install my Phase Perfect, in preparation for a 5.5 KW 3-phase slider. He just asked me this question “Do you know if the table saw requires a neutral?” I have no

How about a box of 10 for $180 from Felder? Unless these are the wrong size… https://www.felder-group.com/en-us/shop/reversible-blades-sc579679/reversible-blade-width-12-mm-sp124298 Sent: Tuesday,

It is an odd size. When I bought replacements I tried my Leitz rep (Brisbane) and he could not source the cutters for any price. Felder had them in stock. Warm regards, Lucky

The catalog for H3D tool Corp. lists 12 x 6 x 1.5 mm shaper cutter carbide inserts. You can reach them at this number: 1-828-397-2467. I do not know if they stock them or what the price would be, but

Hi, for sale Phase Perfect Enterprise (not the entry level unit) in upgraded NEMA 3R outdoor enclosure and factory surge suppression. Low hours like new condition asking $4,500.? PTE015R-S, R in

So I’d say Shars is a dead end metalwork stuff look into leitz leiser Rengate Felder FS tool Schmidt on martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330

Reach out to csp tooling via instagram, not sure if they have a website. They charge a fair price and probably have that size cutter in stock

The main cutters are a weird 12mm long by 6mm wide with 1.5mm thickness. I haven't been able to find them except on felder site and they are spendy... [email protected]> wrote:

I have a Felder dado set that uses inserts. I have not looked into exact replacements but they look like typical inserts for tooling.? In the US, Shars is an import source for indexable inserts.

Copied from my FB post: Received parts for what Felder calls "Precision Miter Unit with Pin Locating System". Installation was straight forward and can be done in 15 mins, just read the picture

I have a k700s with the adjustable groove cutter set. I am in need of the main cutter inserts and felder has them listed for 43 for 2 before tax/shipping.... does anybody have an aftermarket source?

Hi Aaron, This picture of simple model shows what appears to be a fan at the bottom. It would be nice if an owner of simple model could chime in with details. The manual says “Hard starting loads

I read the article. My only concern is with the recommended 0.2 mm pass. Depending upon the species it may require decent amount of sanding to get rid of infeed roller marks. Perhaps that is better