Re: Felder Branded Machine Securement "Buttons"
Post some photos please.? David Best - via mobile phone?
toggle quoted message
Show quoted text
On Jan 21, 2024, at 5:51?PM, bombamanwa@... wrote:
?I was going to ask before I started down the 3D Printing route if anyone knew of the price/part number and availability of the small grey "Buttons" that Felder uses on their felder branded machines to hold in access panels. Whilst I hate the design I've got a few broken ones and would like to replace them.
Thanks
Karl
|
Felder Branded Machine Securement "Buttons"
I was going to ask before I started down the 3D Printing route if anyone knew of the price/part number and availability of the small grey "Buttons" that Felder uses on their felder branded machines to hold in access panels. Whilst I hate the design I've got a few broken ones and would like to replace them.
Thanks
Karl
|
Re: Overarm Guard Modification
I’m in the same camp as mark. Simple and easy enough to leave unbolted.?
toggle quoted message
Show quoted text
On Jan 21, 2024, at 9:46 AM, Mark Kessler <mkessler10@...> wrote:
?I leave mine unbolted?
|
Re: Overarm Guard Modification
I have not tried leaving it unconnected. It would work as dust collection, but I wondered how susceptible it would be to bumps and vibration.
I’ve also been looking at switchable magnets, like Magswitch. These are strong, but there is still the issue of switching them without walking around the saw. A regular magnet would work as a detent, releasing with just a tug on the arm. I probably have something laying around to experiment with.
Thanks for the ideas! ?
--
John Hinman
Boise ID
K700S and A941
|
Re: Overarm Guard Modification
Strong ?? Designing and building for 50 years
toggle quoted message
Show quoted text
On Jan 21, 2024, at 8:46?AM, Mark Kessler <mkessler10@...> wrote:
?I leave mine unbolted?
|
Re: Overarm Guard Modification
|
Re: Felder X-roll short crosscut fence. Initial setup
Steven,
I would purchse set today if they were available.
Were you able to get CAD file to have these Fabbed by FIXtiv?
Thanks Scott G
(I am still shocked that some of the Felder sliders T-slot is so sloppy)
|
Re: K975 support table. Is it square to the blade?
James I sent you a DM on this. ?Let me know if you didn’t get it.
David Best
DBestWorkshop@...
https://www.flickr.com/photos/davidpbest/collections/
https://www.youtube.com/@David_Best
toggle quoted message
Show quoted text
On Jan 20, 2024, at 3:16?PM, James Heathcock via groups.io <james.heathcock@...> wrote:
That's the one, yes.? Is this the extension table you have?
On Jan 20, 2024, at 2:38?PM, James Heathcock via <james.heathcock= [email protected]> wrote:
I have the short 500mm x 150mm support table that is fixed directly to the P channel via a clamping mechanism. My question is, could I trust this table to be square to the blade at all times if I were to mount the rear section of a fritz and franz jig to it? I currently use a shop made, oak t track bar to mount the jig to the slider T slot but due to the non-uniform dimensions of the t slot throughout its length, I'm getting sick of the play and slop. I was hoping to utilise the support table to 'fix' the jig to using a t bolt and 90 degree aluminum extrusion bracket. I figured that as the P channel is a true reference point then anything mounted to it could be trusted as being true to the blade? Is this correct?
Thanks?
James?
|
Thank you David. With the help from your “Survival Guide” the K700S is setup and working great! ?Now just need to transition from cabinet saw techniques to slider techniques.? Regards,
toggle quoted message
Show quoted text
On Jan 20, 2024, at 2:25 PM, David P. Best <dbestworkshop@...> wrote:
You will find the jointer table alignment process fully documented in my Jointer Table Alignment Guide which you can download at this link:
David Best
DBestWorkshop@...
https://www.flickr.com/photos/davidpbest/collections/
https://www.youtube.com/@David_Best
On Jan 20, 2024, at 10:08?AM, dmiller823a via groups.io <dmiller823a@...> wrote:
Hi everyone - new to the FOG,
Was wondering if anyone had instructions for commissioning a Felder AD941 16" jointer/planer? Or, instructions on how to adjust the jointer and planer tables, if needed.
There was no such information included from Felder - no surprise, and I've been told it will take a month in my part of the country to have a tech come out and commission the unit.
Any information would be appreciated.
Regards,
Darrell Miller
|
Re: K975 support table. Is it square to the blade?
toggle quoted message
Show quoted text
Is this the extension table you have?
On Jan 20, 2024, at 2:38?PM, James Heathcock via <james.heathcock= [email protected]> wrote:
I have the short 500mm x 150mm support table that is fixed directly to the P channel via a clamping mechanism. My question is, could I trust this table to be square to the blade at all times if I were to mount the rear section of a fritz and franz jig to it? I currently use a shop made, oak t track bar to mount the jig to the slider T slot but due to the non-uniform dimensions of the t slot throughout its length, I'm getting sick of the play and slop. I was hoping to utilise the support table to 'fix' the jig to using a t bolt and 90 degree aluminum extrusion bracket. I figured that as the P channel is a true reference point then anything mounted to it could be trusted as being true to the blade? Is this correct?
Thanks?
James?
|
Re: K975 support table. Is it square to the blade?
Is this the extension table you have?
David Best
DBestWorkshop@...
https://www.flickr.com/photos/davidpbest/collections/
https://www.youtube.com/@David_Best
toggle quoted message
Show quoted text
On Jan 20, 2024, at 2:38?PM, James Heathcock via groups.io <james.heathcock@...> wrote:
I have the short 500mm x 150mm support table that is fixed directly to the P channel via a clamping mechanism. My question is, could I trust this table to be square to the blade at all times if I were to mount the rear section of a fritz and franz jig to it? I currently use a shop made, oak t track bar to mount the jig to the slider T slot but due to the non-uniform dimensions of the t slot throughout its length, I'm getting sick of the play and slop. I was hoping to utilise the support table to 'fix' the jig to using a t bolt and 90 degree aluminum extrusion bracket. I figured that as the P channel is a true reference point then anything mounted to it could be trusted as being true to the blade? Is this correct?
Thanks?
James?
|
K975 support table. Is it square to the blade?
I have the short 500mm x 150mm support table that is fixed directly to the P channel via a clamping mechanism. My question is, could I trust this table to be square to the blade at all times if I were to mount the rear section of a fritz and franz jig to it? I currently use a shop made, oak t track bar to mount the jig to the slider T slot but due to the non-uniform dimensions of the t slot throughout its length, I'm getting sick of the play and slop. I was hoping to utilise the support table to 'fix' the jig to using a t bolt and 90 degree aluminum extrusion bracket. I figured that as the P channel is a true reference point then anything mounted to it could be trusted as being true to the blade? Is this correct?
Thanks?
James?
|
Re: Overarm Guard Modification
David,? The bolt with the Kip lever is M8x1.25, and it threads into the square HSS section of the overarm guard. The M8 bolt snugs the arm up against two cap screws. A carriage bolt provides vertical support.  -- John Hinman Boise ID K700S and A941
|
You will find the jointer table alignment process fully documented in my Jointer Table Alignment Guide which you can download at this link:
David Best
DBestWorkshop@...
https://www.flickr.com/photos/davidpbest/collections/
https://www.youtube.com/@David_Best
toggle quoted message
Show quoted text
On Jan 20, 2024, at 10:08?AM, dmiller823a via groups.io <dmiller823a@...> wrote:
Hi everyone - new to the FOG,
Was wondering if anyone had instructions for commissioning a Felder AD941 16" jointer/planer? Or, instructions on how to adjust the jointer and planer tables, if needed.
There was no such information included from Felder - no surprise, and I've been told it will take a month in my part of the country to have a tech come out and commission the unit.
Any information would be appreciated.
Regards,
Darrell Miller
|
Hi everyone - new to the FOG,
Was wondering if anyone had instructions for commissioning a Felder AD941 16" jointer/planer? Or, instructions on how to adjust the jointer and planer tables, if needed.
There was no such information included from Felder - no surprise, and I've been told it will take a month in my part of the country to have a tech come out and commission the unit.
Any information would be appreciated.
Regards,
Darrell Miller
|
Re: Overarm Guard Modification
John, you can see my remote-release setup here: ?https://flic.kr/s/aHskt9MBRv
One my machine, the system that locks the overhead swivel-arm in place is a spring loaded detent actuator. ?From your photos, it appears that the Kipp lever in the photo actually threads into a tapped hole in the swivel arm? ?Or is that Kipp lever just pressing against the swivel-arm and it’s somehow locked/stopped on the opposite side? ?Please post a few additional photos that more-fully illustrate how this arm is unlocked to swivel forward. ?Also, what is the diameter of the Kipp lever threaded shaft - I’m guessing it’s just under 10mm?
David Best
DBestWorkshop@...
https://www.flickr.com/photos/davidpbest/collections/
https://www.youtube.com/@David_Best
toggle quoted message
Show quoted text
On Jan 20, 2024, at 11:06?AM, John Hinman <jhinman1911@...> wrote:
Moving the overarm guard/dust hood out of the way requires walking around the saw and unscrewing a bolt. This is a nuisance if all that is needed is to get the guard out of the way to check a set-up.
I think some saws have a more convenient set-up. If I recall correctly David Best once described being able to pull a wire to release the arm, from the operator position.
Has anyone modified the bolt connection to make it a quick-release? Any good ideas?
The picture shows the bolt, with a Kip lever, on my saw.
<IMG_4907.jpeg>
--
John Hinman
Boise ID
K700S and A941
|
Re: Overarm Guard Modification
 Designing and building for 50 years
toggle quoted message
Show quoted text
On Jan 20, 2024, at 1:40?PM, mac campshure <mac512002@...> wrote:
? I put a few slots in the guard and couple screws, so I can remove when in the way,
Designing and building for 50 years On Jan 20, 2024, at 1:30?PM, John Hinman <jhinman1911@...> wrote:
?Bill, I’m curious what the pin set-up looks like. I don’t have a pin, just a bolt that goes into the arm to hold it in place.
Someday when you are in your shop, would you please share a picture of the pin and cable set-up?
Thanks!
--
John Hinman
Boise ID
K700S and A941
|
Re: Overarm Guard Modification
I put a few slots in the guard and couple screws, so I can remove when in the way,
Designing and building for 50 years
toggle quoted message
Show quoted text
On Jan 20, 2024, at 1:30?PM, John Hinman <jhinman1911@...> wrote:
?Bill, I’m curious what the pin set-up looks like. I don’t have a pin, just a bolt that goes into the arm to hold it in place.
Someday when you are in your shop, would you please share a picture of the pin and cable set-up?
Thanks!
--
John Hinman
Boise ID
K700S and A941
|
Re: Overarm Guard Modification
Bill, I’m curious what the pin set-up looks like. I don’t have a pin, just a bolt that goes into the arm to hold it in place.
Someday when you are in your shop, would you please share a picture of the pin and cable set-up?
Thanks!
--
John Hinman
Boise ID
K700S and A941
|
Re: Overarm Guard Modification
I don’t have a picture for you because I’m on vacation, but I used a throttle cable setup for a lawnmower to pull and reset the pin. Bill Belanger
toggle quoted message
Show quoted text
On Jan 20, 2024, at 14:06, John Hinman <jhinman1911@...> wrote:
?Moving the overarm guard/dust hood out of the way requires walking around the saw and unscrewing a bolt. This is a nuisance if all that is needed is to get the guard out of the way to check a set-up. I think some saws have a more convenient set-up. If I recall correctly David Best once described being able to pull a wire to release the arm, from the operator position. Has anyone modified the bolt connection to make it a quick-release? Any good ideas? The picture shows the bolt, with a Kip lever, on my saw. <IMG_4907.jpeg> -- John Hinman Boise ID K700S and A941
|
David P. Best
Dan Gavrilyuk
Bill Belanger