开云体育

Brian: I opted for a cable with 0.5mm2 wire. I realise that the cable only has to deal with the contactor coil current but I wanted something a little more robust than the minimum. It's a trivial

Outstanding. Thanks Bill. David Best DBestWorkshop@... https://www.flickr.com/photos/davidpbest/collections/ https://www.youtube.com/@David_Best

Posted some T nuts to the Etsy shop. https://www.etsy.com/listing/1417618716/t-nuts-pair-for-festool-clamping-on-the <jonathansamways@...> wrote:

Does it sound anything like Aarons? How about posting a video. David Best DBestWorkshop@... https://www.flickr.com/photos/davidpbest/collections/ https://www.youtube.com/@David_Best

I have a single phase KF700, very quiet while staring and running.

Thanks Lourens. As an aside, I am aware how much your equipment must have cost you. The Aussie Dollar is about 60% of the US Dollar, but the South African Rand is 10% of the AUD. I suspect that you

I ran my cable out one of the plastic caps on the end of the chassis below the slider and hang the switch box off the F-channel on the side of the slider. I would suggest a lighter coil cord than what

Tom & James - thanks, I'll take a closer look at the Mirkas.??? But TBH, I do like the Plug-It cords. Brett - I run 5m 27mm off of a CT-26 and -36.? I too was concerned about lack of performance

Tom, Had an old CTmidi c.2010 with the small hose. Latest CTmidi purchased had I believe the 36mm, but maybe it was 32mm. Way better flow performance and less clogging esp. When vacuuming up things

Well, to be honest with you, your machine is producing a lot of low frequency noise with just the main saw arbor running. I hear a loud rumble at 117 Hz which sounds like the electronic brake is

Okay, new videos.? I removed all blades so that we can hear exactly what the motors are doing. K700S without scoring motor - all blades removed: https://www.youtube.com/watch?v=ZG4cVNLxOks K700S WITH

The following files and folders have been updated in the Files area of the [email protected] group. * /FOG made products/Remote Slider Switches.pdf (

Hi Dave, This may not be what you are looking for but may give you am idea. I prefer wireless over a cord. I don't think I put it in files, so I will do that. There are at least 2 more solutions in

I'm tired of fumbling underneath the slider to find the saw start/stop buttons on my BF6 so am about to add switches to the end of the slider, with a 4-way curly cable back to the original switches.

Hi Rich, Thanks for the feedback on the 5m hose, I'll give it a closer look. I do have a Mirka Deros sander, the 6" pad, 2.5mm orbit configuration. I really like it, particularly for fine sanding

it was certainly easier to buy brian’s excellent gear several years ago when the aussie dollar was for a brief time worth a little more then the greenback. it’s all snakes and ladders, just like

I have a Mirka DEROS 650X CV, it is 6" with 5mm stroke. I also bought the 5" pad (MK-915GV28-130), so I can use it as a 5" sander. That is the main reason I bought DEROS, otherwise I would need to buy

Hi Derek, I don’t know about wages/cost of living, that’s why I asked. Seems you can find just about any figure you want from high to low on the internet, so it’s hard to say what is correct. As

5m hoses here, no regrets, sometimes I need to scoot it away from under my feet, but I'd rather that, than not have enough length.? Also good for overhead stand, hang from ceiling, etc. Tom - Do you

…here is one data point from the OECD - average wages - measured in US$ - please note that is one of many indicators for comparison.