Re: 3D printer file for KF700 crosscut fence block
I guess it would have been easier for me to include the link.... duh!
Brian Lamb blamb11@... lambtoolworks.com
On Saturday, March 29, 2025 at 09:32:27 AM MST, Brian Lamb via groups.io <blamb11@...> wrote:
Hi Jason,
Sorry it took so long, had to find mine and then blue print it and make the stl file. I did not test print it, and depending on how accurate your 3D print is, you might have to make adjustments for the proper thickness front to back so it matches the stops. I tried to email the stl file, too big. So I'll see if I can load it onto the files portion of the FOG.
Brian Lamb blamb11@... lambtoolworks.com
On Thursday, March 27, 2025 at 06:15:02 PM MST, Jason Holtz via groups.io <jholtzy@...> wrote:
Has anyone made a file for this doohickey? 2001 vintage KF700.
--
Jason
J. Holtz Furniture
3307 Snelling Ave. South
Minneapolis, MN 55406
|
Re: 3D printer file for KF700 crosscut fence block
Hi Jason,
Sorry it took so long, had to find mine and then blue print it and make the stl file. I did not test print it, and depending on how accurate your 3D print is, you might have to make adjustments for the proper thickness front to back so it matches the stops. I tried to email the stl file, too big. So I'll see if I can load it onto the files portion of the FOG.
Brian Lamb blamb11@... lambtoolworks.com
On Thursday, March 27, 2025 at 06:15:02 PM MST, Jason Holtz via groups.io <jholtzy@...> wrote:
Has anyone made a file for this doohickey? 2001 vintage KF700.
--
Jason
J. Holtz Furniture
3307 Snelling Ave. South
Minneapolis, MN 55406
|
David,
?
I have been considering epoxy to? cover my 20 year old stained concrete floor.? It's getting pretty bad.? ?I did not know vinyl tile was a less expensive option.? Is that cost comparison with labor installed?? ?
?
I have seen the plastic and rubber snap key systems but did not like the thickness nor the non-solid feel.? I haven't gotten serious yet but understand there are some "epoxy" products to avoid and, like all coating systems, preparation is key.? Clean up, color and pattern will also determine the system. I'm thinking a lighter, solid color for better ambient lighting and to be able to find #2 setscrews and 1/16" circlips.?
?
I like the 1/8" thickness, soft gray color/pattern and glue down installation.? I will be interested in which direction you go.?
|
Jason -?
Tambours would solve the problem. They were early on ruled out due to budget constraints, but I should take another look. Thanks!
Hey Brett, I think tambour doors is your solution. I suspect the weight of a bifold door on the flipper hardware will be problematic. You can make the tambour look like a solid slab when closed but it is a lot of work.
Jason
Jason Holtz
J. Holtz Furniture
3307 Snelling Ave. South Minneapolis, MN 55406
612 432-2765
--
Jason
J. Holtz Furniture
3307 Snelling Ave. South
Minneapolis, MN 55406
-- Brett Wissel Saint Louis Restoration 1831 S Kingshighway Blvd (at Shaw Blvd) St Louis, MO 63110 314.772.2167 brett@...
|
Hey Brett, I think tambour doors is your solution. I suspect the weight of a bifold door on the flipper hardware will be problematic. You can make the tambour look like a solid slab when closed but it is a lot of work.
Jason
Jason Holtz
J. Holtz Furniture
3307 Snelling Ave. South Minneapolis, MN 55406
612 432-2765 -- Jason J. Holtz Furniture 3307 Snelling Ave. South Minneapolis, MN 55406
|
Re: ProLock spindle locking mech
Stan I think have one more - I am out of town until next sat. ? If you like I can confirm and get back to you
Get
toggle quoted message
Show quoted text
What was the pm for the 1.25” prolock? Would like to order one. Thanks.?
--
Stan Blaszczyk
Causal Maker of Stuff
Cincinnati, OH
-- Michael Marsico
|
Re: ProLock spindle locking mech
What was the pm for the 1.25” prolock? Would like to order one. Thanks.?
--
Stan Blaszczyk
Causal Maker of Stuff
Cincinnati, OH
|
Re: Hammer C3-41 Sliding Table Question
#hammer
|
Re: Hammer C3-41 Sliding Table Question
#hammer
Thanks, David. I don't think it makes a difference but I was surprised to see that much of a kick up. The machine was new to me in 2021 and I moved it into my shop with a pallet jack and uncrated it myself. So that table has not been used to move or lift the machine.
|
Re: For Sale - Felder Eccentric Clamp
#forsale
The clamp has been sold, and is on its way to Brad. ?Some unfortunate mail carrier is going to be lugging a 17 pound Priority Mail package in their mail delivery bag! ??
|
They will be narrow enough once folded to go into the 16"-18" depth of the cabinet as well. Disadvantage is the Soss hinges might be visible to the whole world on the edges when folded though. Check with Hafele, I bet they have some sort of solution for all of this
Brian Lamb blamb11@... lambtoolworks.com
On Friday, March 28, 2025 at 02:52:05 PM MST, Brett Wissel via groups.io <brettwissel@...> wrote:
Actually good point, making the two doors bi-fold would limit them being out of proportion, that's a way to make them small enough to not be problematic - thanks for that suggestion.
So, you want four doors to look like two? And then they have to retract into the cabinet? Maybe Soss hidden hinges on the two halves and then use flipper dooor hardware for the two assemblies.
On Friday, March 28, 2025 at 02:27:42 PM MST, Brett Wissel via <brettwissel= [email protected]> wrote:
I'm looking for expertise on flipper doors, applicability, caveats. Considering a project and concerned that a 2-sidemount door cabinet opening will be too out-of-proportion when open, but still want it to look like a 2-door cabinet opening when closed up.
*Opening 48-54", must be clear due to contents it is storing inside *Depth of cabinet about 16"-18" *Only occasional use, perhaps monthly.
Any real world experience or limitations for an opening this wide that still looks like a 2-door cabinet?
-- Brett Wissel Saint Louis Restoration 1831 S Kingshighway Blvd (at Shaw Blvd) St Louis, MO 63110 314.772.2167 brett@...
-- Brett Wissel Saint Louis Restoration 1831 S Kingshighway Blvd (at Shaw Blvd) St Louis, MO 63110 314.772.2167 brett@...
|
Actually good point, making the two doors bi-fold would limit them being out of proportion, that's a way to make them small enough to not be problematic - thanks for that suggestion.
So, you want four doors to look like two? And then they have to retract into the cabinet? Maybe Soss hidden hinges on the two halves and then use flipper dooor hardware for the two assemblies.
On Friday, March 28, 2025 at 02:27:42 PM MST, Brett Wissel via <brettwissel= [email protected]> wrote:
I'm looking for expertise on flipper doors, applicability, caveats. Considering a project and concerned that a 2-sidemount door cabinet opening will be too out-of-proportion when open, but still want it to look like a 2-door cabinet opening when closed up.
*Opening 48-54", must be clear due to contents it is storing inside *Depth of cabinet about 16"-18" *Only occasional use, perhaps monthly.
Any real world experience or limitations for an opening this wide that still looks like a 2-door cabinet?
-- Brett Wissel Saint Louis Restoration 1831 S Kingshighway Blvd (at Shaw Blvd) St Louis, MO 63110 314.772.2167 brett@...
-- Brett Wissel Saint Louis Restoration 1831 S Kingshighway Blvd (at Shaw Blvd) St Louis, MO 63110 314.772.2167 brett@...
|
So, you want four doors to look like two? And then they have to retract into the cabinet? Maybe Soss hidden hinges on the two halves and then use flipper dooor hardware for the two assemblies.
Brian Lamb blamb11@... lambtoolworks.com
On Friday, March 28, 2025 at 02:27:42 PM MST, Brett Wissel via groups.io <brettwissel@...> wrote:
I'm looking for expertise on flipper doors, applicability, caveats. Considering a project and concerned that a 2-sidemount door cabinet opening will be too out-of-proportion when open, but still want it to look like a 2-door cabinet opening when closed up.
*Opening 48-54", must be clear due to contents it is storing inside *Depth of cabinet about 16"-18" *Only occasional use, perhaps monthly.
Any real world experience or limitations for an opening this wide that still looks like a 2-door cabinet?
-- Brett Wissel Saint Louis Restoration 1831 S Kingshighway Blvd (at Shaw Blvd) St Louis, MO 63110 314.772.2167 brett@...
|
I'm looking for expertise on flipper doors, applicability, caveats. Considering a project and concerned that a 2-sidemount door cabinet opening will be too out-of-proportion when open, but still want it to look like a 2-door cabinet opening when closed up.
*Opening 48-54", must be clear due to contents it is storing inside *Depth of cabinet about 16"-18" *Only occasional use, perhaps monthly.
Any real world experience or limitations for an opening this wide that still looks like a 2-door cabinet?
-- Brett Wissel Saint Louis Restoration 1831 S Kingshighway Blvd (at Shaw Blvd) St Louis, MO 63110 314.772.2167 brett@...
|
Re: Fixing Felder X-roll short cross cut fence T-nut - AKA group buy of improved T-nut
I too am interested so please count me in.
?
Ted Earnhardt
|
Re: Adding Remote Control Switches on Felder
I made a folder in the Photos tab titled Hammer K3 Winner Schematic/Wiring diagram. I will also attach a .jpg here.
|
Re: Adding Remote Control Switches on Felder
Photos are commonly attached. Be sure to save it in a picture format (jpg, png, etc) first. I see .htm extension, which may be the issue.
toggle quoted message
Show quoted text
On Mar 28, 2025, at 3:27?PM, Kevin Wells via groups.io <kjwells54@...> wrote: ? It looks like the image doesn't load. Do I need a particular file type?
|
Re: Adding Remote Control Switches on Felder
Hi Kevin,
I just get a black screen with menu option when I open the attachment on my iphone. Same result if I save it in files.
toggle quoted message
Show quoted text
On Mar 28, 2025, at 3:25?PM, Kevin Wells via groups.io <kjwells54@...> wrote: ? Thank you Imran. I'm attaching an image of the schematic/wiring diagram that came with the K3 Winner. Some have asked to keep this topic public in the event the solution will work for them. Hi Kevin,
I assume you are asking me about my write-up of the many I shared. If so, I should be able to confirm, if you share the electrical schematic of your machine with me. You can share it here or send it privately by clicking, “Reply to Sender”, at bottom of the message. ? Imran, any idea if this will also work for a K3?
--
<Photo -K3 Schematic..htm>
|
Re: Adding Remote Control Switches on Felder
It looks like the image doesn't load. Do I need a particular file type?
|
Re: Adding Remote Control Switches on Felder
Thank you Imran. I'm attaching an image of the schematic/wiring diagram that came with the K3 Winner. Some have asked to keep this topic public in the event the solution will work for them.
Hi Kevin,
I assume you are asking me about my write-up of the many I shared. If so, I should be able to confirm, if you share the electrical schematic of your machine with me. You can share it here or send it privately by clicking, “Reply to Sender”, at bottom of the message. ? Imran, any idea if this will also work for a K3?
|
Jonathan Smith
Jason Holtz
Kevin Wells
imran