Re: Source for custom knives for 40 mm Felder safety cutter
My $.02, if looking for custom knives 3/8" corrugated is a better value than 40/50mm pin knives. At least in my experience.?
On Sat, Dec 7, 2024, 11:53 AM imranindiana via <imranindiana= [email protected]> wrote: Sorry for the confusion caused by the picture I shared as an example. As the title say and the end of my original msg says, “I am looking for someone who can do a custom knife set for me, 40 mm tall.”
Brent, You are correct, most Amana series don’t come with limiters. FWIW, I have used a rebate limiter with one I bought that did not come with limiter but I got them from Felder after 6 weeks or so. ? Looks like CMT 016 profile cutter's price is only 50% of the Dimar cutter's price from . Doing woodwooding is really expensive in Canada.
Btw, looks like Imran is looking for the limiter to the 016 profile commodity cutter from Felder.?
James
On Sat, Dec 7, 2024 at 10:58?AM Jared Sankovich via <Sankovichj= [email protected]> wrote: If you just want the standard commodity 40/50mm profile knives most places (including Amazon) carry them. The the number system is standardized. Cmt or amana will be common in the us.?
016 knife:
I bought some Dimar profile cutters and limiters from The profile cutters Felder offers are common Euro profile?cutters. Those profiles are offered by many different companies.? Amana Tool 64F016 Imran mentioned is the same as?
Did you want limiters too?? Not all north American shops are familiar with them though some are.
|
Re: Source for custom knives for 40 mm Felder safety cutter
Imran,
This is the limiter for #016 profile cutter from . Maybe you can find a US supplier?selling at the lower price.
James
On Sat, Dec 7, 2024 at 11:53?AM imranindiana via <imranindiana= [email protected]> wrote: Sorry for the confusion caused by the picture I shared as an example. As the title say and the end of my original msg says, “I am looking for someone who can do a custom knife set for me, 40 mm tall.”
Brent, You are correct, most Amana series don’t come with limiters. FWIW, I have used a rebate limiter with one I bought that did not come with limiter but I got them from Felder after 6 weeks or so. ? Looks like CMT 016 profile cutter's price is only 50% of the Dimar cutter's price from . Doing woodwooding is really expensive in Canada.
Btw, looks like Imran is looking for the limiter to the 016 profile commodity cutter from Felder.?
James
On Sat, Dec 7, 2024 at 10:58?AM Jared Sankovich via <Sankovichj= [email protected]> wrote: If you just want the standard commodity 40/50mm profile knives most places (including Amazon) carry them. The the number system is standardized. Cmt or amana will be common in the us.?
016 knife:
I bought some Dimar profile cutters and limiters from The profile cutters Felder offers are common Euro profile?cutters. Those profiles are offered by many different companies.? Amana Tool 64F016 Imran mentioned is the same as?
Did you want limiters too?? Not all north American shops are familiar with them though some are.
|
Re: Source for custom knives for 40 mm Felder safety cutter
Sorry for the confusion caused by the picture I shared as an example. As the title say and the end of my original msg says, “I am looking for someone who can do a custom knife set for me, 40 mm tall.”
Brent, You are correct, most Amana series don’t come with limiters. FWIW, I have used a rebate limiter with one I bought that did not come with limiter but I got them from Felder after 6 weeks or so.
toggle quoted message
Show quoted text
On Dec 7, 2024, at 11:19?AM, James Zhu via groups.io <james.zhu2@...> wrote: ? Looks like CMT 016 profile cutter's price is only 50% of the Dimar cutter's price from . Doing woodwooding is really expensive in Canada.
Btw, looks like Imran is looking for the limiter to the 016 profile commodity cutter from Felder.?
James
On Sat, Dec 7, 2024 at 10:58?AM Jared Sankovich via <Sankovichj= [email protected]> wrote: If you just want the standard commodity 40/50mm profile knives most places (including Amazon) carry them. The the number system is standardized. Cmt or amana will be common in the us.?
016 knife:
I bought some Dimar profile cutters and limiters from The profile cutters Felder offers are common Euro profile?cutters. Those profiles are offered by many different companies.? Amana Tool 64F016 Imran mentioned is the same as?
Did you want limiters too?? Not all north American shops are familiar with them though some are.
|
Re: Taller resaw fence for Felder FB610
Thanks for the references. ?There are some really interesting points in there around drift. I’m inclined to repeat some of Derek’s experiments.
|
Re: sliding table saw: parallel fence vs 2nd crosscut fence?
#k700s
Mac - I hear you on that.? I disabled Siri on my iPhone, it is totally unnerving.
cheers, Rich Markiewicz
|
Re: sliding table saw: parallel fence vs 2nd crosscut fence?
#k700s
I do not have dementia!! Somehow, a goofy phone was listening to myself and my friend Tom troubleshoot a problem on my lath which we fixed and have no idea how we fixed it that’s nerving anyhow sorry for the post. Makes absolutely no sense. Nothing to do with what you guys are talking about. Peace smack Designing and building for 50 years
toggle quoted message
Show quoted text
On Dec 7, 2024, at 9:51?AM, mac campshure <mac512002@...> wrote:
? ? Wade great idea, I will be happy to sell my Design manufacturing fixtures and patterns a reasonable cost. Electric bolt underneath I don’t think there’s any bolts down there lift up again once seems like around here. It’s the safest way to take this off Pin casting can’t can’t. I think the easiest way is just to take that piss off right here do you think no idea let’s try and just pull it this way OK no it’s caught on the bottom on the bottom there. It won’t lift it up. It’s caught up over the edge. It’s like a channel 3/16 730 very well Metric. This is probably three different type of bolts on it metric standard and Lithuanian or something like that. Not really have any English tools. It’s pretty common the Woodweb thread European and older their style. It’s very very similar to to find SAE American SAE there is a little difference like maybe half inches 11 threads per inch and I think Wentworth might be 12 probably really annoying when you’re looking at a fastener like this should go in there. Nice thing about this when you take this off it should sit right back in the right place sit sitting on that ledge down there, but that is a stupid fucking way to do this. Jesus Christ didn’t I went to the easiest method I guess yeah maybe but it is what it is. They’re having the shelf behind her. That’s just sitting right there and moving probably right there.Sure, your bread was manufacture. It’s 947 place. I guess we get back. I can come back together for sure. These are the two bolts for that if you’re itching to get into making something that would be all you really need to hook up to let me ask nate if he’s got a few minutes for you. It would be best if we could put it back together.
You would need at least vertical mail with a Yeah, see that’s it that there I don’t think soo whe where is the longer bullshit that fits in here what else Allan ranchermedium travel. Designing and building for 50 years On Oct 9, 2024, at 12:17?PM, netanel.belgazal via groups.io <netanel.belgazal@...> wrote:
? I am like John.
Using the parallel fence and the outrigger to cut long boards. For short pieces I am using David bedrosian F&F.
?
another thing worth to mention is that the parallel fence is mounted on the P channel of the rail, which isn’t guaranteed to be parallel to the blade, so you can have few mm difference between two spots on the slider.
?
i built a magnet base to stop block like David Lucky did.
|
Re: Source for custom knives for 40 mm Felder safety cutter
Looks like CMT 016 profile cutter's price is only 50% of the Dimar cutter's price from . Doing woodwooding is really expensive in Canada.
Btw, looks like Imran is looking for the limiter to the 016 profile commodity cutter from Felder.?
James
On Sat, Dec 7, 2024 at 10:58?AM Jared Sankovich via <Sankovichj= [email protected]> wrote: If you just want the standard commodity 40/50mm profile knives most places (including Amazon) carry them. The the number system is standardized. Cmt or amana will be common in the us.?
016 knife:
I bought some Dimar profile cutters and limiters from The profile cutters Felder offers are common Euro profile?cutters. Those profiles are offered by many different companies.? Amana Tool 64F016 Imran mentioned is the same as?  James
Did you want limiters too?? Not all north American shops are familiar with them though some are.
|
Re: Source for custom knives for 40 mm Felder safety cutter
If you just want the standard commodity 40/50mm profile knives most places (including Amazon) carry them. The the number system is standardized. Cmt or amana will be common in the us.?
016 knife:
I bought some Dimar profile cutters and limiters from The profile cutters Felder offers are common Euro profile?cutters. Those profiles are offered by many different companies.? Amana Tool 64F016 Imran mentioned is the same as?  James
Did you want limiters too?? Not all north American shops are familiar with them though some are.
|
Re: sliding table saw: parallel fence vs 2nd crosscut fence?
#k700s
? Wade great idea, I will be happy to sell my Design manufacturing fixtures and patterns a reasonable cost. Electric bolt underneath I don’t think there’s any bolts down there lift up again once seems like around here. It’s the safest way to take this off Pin casting can’t can’t. I think the easiest way is just to take that piss off right here do you think no idea let’s try and just pull it this way OK no it’s caught on the bottom on the bottom there. It won’t lift it up. It’s caught up over the edge. It’s like a channel 3/16 730 very well Metric. This is probably three different type of bolts on it metric standard and Lithuanian or something like that. Not really have any English tools. It’s pretty common the Woodweb thread European and older their style. It’s very very similar to to find SAE American SAE there is a little difference like maybe half inches 11 threads per inch and I think Wentworth might be 12 probably really annoying when you’re looking at a fastener like this should go in there. Nice thing about this when you take this off it should sit right back in the right place sit sitting on that ledge down there, but that is a stupid fucking way to do this. Jesus Christ didn’t I went to the easiest method I guess yeah maybe but it is what it is. They’re having the shelf behind her. That’s just sitting right there and moving probably right there.Sure, your bread was manufacture. It’s 947 place. I guess we get back. I can come back together for sure. These are the two bolts for that if you’re itching to get into making something that would be all you really need to hook up to let me ask nate if he’s got a few minutes for you. It would be best if we could put it back together.
You would need at least vertical mail with a Yeah, see that’s it that there I don’t think soo whe where is the longer bullshit that fits in here what else Allan ranchermedium travel. Designing and building for 50 years
toggle quoted message
Show quoted text
On Oct 9, 2024, at 12:17?PM, netanel.belgazal via groups.io <netanel.belgazal@...> wrote:
? I am like John.
Using the parallel fence and the outrigger to cut long boards. For short pieces I am using David bedrosian F&F.
?
another thing worth to mention is that the parallel fence is mounted on the P channel of the rail, which isn’t guaranteed to be parallel to the blade, so you can have few mm difference between two spots on the slider.
?
i built a magnet base to stop block like David Lucky did.
|
Re: Source for custom knives for 40 mm Felder safety cutter
I bought some Dimar profile cutters and limiters from The profile cutters Felder offers are common Euro profile?cutters. Those profiles are offered by many different companies.? Amana Tool 64F016 Imran mentioned is the same as?  James
Did you want limiters too?? Not all north American shops are familiar with them though some are.
|
Re: Source for custom knives for 40 mm Felder safety cutter
Did you want limiters too?? Not all north American shops are familiar with them though some are.
|
Re: Source for custom knives for 40 mm Felder safety cutter
Thanks Jared. Will contact him instead.
toggle quoted message
Show quoted text
On Dec 7, 2024, at 9:32?AM, Jared Sankovich via groups.io <Sankovichj@...> wrote: ? That must be a different mt tool.?
Neil is in Baltimore.
On the? plus side he is extremely fast. I've had corrugated knives in less than 24 hours from emailing a drawing to the knives showing up at my door.? On Sat, Dec 7, 2024, 9:23 AM imranindiana via <imranindiana= [email protected]> wrote: Thanks Joe and Jared. MT Tools is in Schaumburg, IL and be great for me. Will contact them Monday. On Dec 7, 2024, at 9:19?AM, Jared Sankovich via <Sankovichj= [email protected]> wrote: ? Joe, you are correct, I've had Neil cut 40mm knives.? [Edited Message Follows]
I’ve had Hot Knives make those. They can use the better and thicker steel also. Those heads will accept 1mm thicker than standard for the knife.
I bet Neil at MT tool could as well.
|
Re: Source for custom knives for 40 mm Felder safety cutter
That must be a different mt tool.?
Neil is in Baltimore.
On the? plus side he is extremely fast. I've had corrugated knives in less than 24 hours from emailing a drawing to the knives showing up at my door.?
On Sat, Dec 7, 2024, 9:23 AM imranindiana via <imranindiana= [email protected]> wrote: Thanks Joe and Jared. MT Tools is in Schaumburg, IL and be great for me. Will contact them Monday. On Dec 7, 2024, at 9:19?AM, Jared Sankovich via <Sankovichj= [email protected]> wrote: ? Joe, you are correct, I've had Neil cut 40mm knives.? [Edited Message Follows]
I’ve had Hot Knives make those. They can use the better and thicker steel also. Those heads will accept 1mm thicker than standard for the knife.
I bet Neil at MT tool could as well.
|
Re: Source for custom knives for 40 mm Felder safety cutter
Thanks Joe and Jared. MT Tools is in Schaumburg, IL and be great for me. Will contact them Monday.
toggle quoted message
Show quoted text
On Dec 7, 2024, at 9:19?AM, Jared Sankovich via groups.io <Sankovichj@...> wrote: ? Joe, you are correct, I've had Neil cut 40mm knives.? [Edited Message Follows]
I’ve had Hot Knives make those. They can use the better and thicker steel also. Those heads will accept 1mm thicker than standard for the knife.
I bet Neil at MT tool could as well.
|
Re: Source for custom knives for 40 mm Felder safety cutter
Joe, you are correct, I've had Neil cut 40mm knives.?
[Edited Message Follows]
I’ve had Hot Knives make those. They can use the better and thicker steel also. Those heads will accept 1mm thicker than standard for the knife.
I bet Neil at MT tool could as well.
|
Re: Source for custom knives for 40 mm Felder safety cutter
I’ve had Hot Knives make those. They can use the better and thicker steel also. Those heads will accept 1mm thicker than standard for the knife.
I bet Neil at MT tool could as well.
|
Re: Source for custom knives for 40 mm Felder safety cutter
Thanks Andy, that is in UK correct. Should have added, looking for a source in USA.
toggle quoted message
Show quoted text
On Dec 7, 2024, at 8:26?AM, Andy via groups.io <andy.raynor08@...> wrote: ? Whitehill tools? On Sat, Dec 7, 2024 at 8:18?AM imranindiana via <imranindiana= [email protected]> wrote: I have not checked with Felder as it is not going to be quick. Took them 6 weeks to get me limiters for a standard knife.
These are also referred to as 64F series or 690 series and look like this
I am looking for someone who can do a custom knife set for me, 40 mm tall.
|
Re: Source for custom knives for 40 mm Felder safety cutter
toggle quoted message
Show quoted text
On Sat, Dec 7, 2024 at 8:18?AM imranindiana via <imranindiana= [email protected]> wrote: I have not checked with Felder as it is not going to be quick. Took them 6 weeks to get me limiters for a standard knife.
These are also referred to as 64F series or 690 series and look like this
I am looking for someone who can do a custom knife set for me, 40 mm tall.
|
Source for custom knives for 40 mm Felder safety cutter
I have not checked with Felder as it is not going to be quick. Took them 6 weeks to get me limiters for a standard knife.
These are also referred to as 64F series or 690 series and look like this
I am looking for someone who can do a custom knife set for me, 40 mm tall.
|
Re: F700Z slider to cast-iron height difference
Hi Cornelius,
It is a shame that you can’t mount PF to your Jointer. As to your concern about bow staying there due to PF, David Best and Lucky have addressed this here may be others too.
In case I don’t remember their recommendation exactly, I would share what I do. I put concave side down. Usually the boards are such that a 3 mm depth of cut is sufficient. Once that amount is removed and the board has traveled ~50 mm the PF picks it up. Can it push the rest of the board down? Well it started out as a cut with no significant downward force just like one would do by hand and is now sitting flush on the outfeed. Pushing it further down at that point, should not do anything to the rest of the board. Boards with significant twist will need some work prior or just should be done by hand.
In this stack of 20 some boards I had to run maybe 4 boards again with 1 mm depth of cut to get them flat.
toggle quoted message
Show quoted text
On Dec 6, 2024, at 4:47?PM, Cornelius via groups.io <Cornelius@...> wrote: ? David - Thank you for your input. The suggestion of building a sled that covers the slider as well as part of the cast iron table (with layers of the foil tape on the bottom side) seems like the perfect solution. The only part that is not yet clear to me is how you deal with the ring inserts that?usually provide support right by the cutterhead. Depending on which size head I use, I would have to mount the entire sled further away from the fence which?may make the support of the workpiece problematic? Also, I suppose you do not clamp above the cast iron with this sled when using the slider since it would flex too much and bind with the cast iron? Would you still recommend I get the Felder tenoning plate for its stiffness and rigid build when I make narrow tenons??
Lastly, when you say my sliding table could use some alignment attention, you mean because?I get binding or because?0.2mm is too much of a height?difference in your opinion? The machine originally shipped with 0.6mm (right) and 0.3mm (left), but I have since corrected this to be 0.2mm on both sides. As you say, the last 10+% on either side are a different story.
Imran - yes, PF for jointer is something else I have been reading up on in the FOG archives. Haven't?come to a conclusion yet. Someone pointed to the fact that a feeder might press a bow out of a board that will be there again once out of the constraints of the feeder? I work a lot with very thick and bulky hardwoods (tropical 50-65 mm thick and 160-200mm wide) so I can't shave several mm off in a single pass. Feeding by hand, I usually go max 1mm in each pass. Another problem is that my AD741 does not come with a place to mount a feeder, so I would need to have a very solid independent place to bolt the feeder where it won't flex away from the jointer, yet can swing away when I need to open the unit to use the thicknesser. Really don't understand why Felder has mounting options for the bigger units, but not for the AD741?
Many thanks to you both for your very helpful feedback!
Cornelius Schultze-Kraft Cyprus
|
imran
Ron Pomeroy