felderownersgroup@groups.io

Re: Electrical question [email protected] All Messages By This Member #137106 John, You can take a look at the plug you have, it can be a good start, it you have 4 wires it defensively don't use natural. If you have 5 wires, it still not guarantee the natural is used at all.
Re: Electrical question [email protected] All Messages By This Member #137105 Imran, The new PP units don't use natural wire as well. only 230V + ground.
Re: Electrical question [email protected] All Messages By This Member #137104 In addition to what Imran wrote, Felder is generally an EU company, and the machines are expected to usually work with EU voltage. The voltage between a phase and the natural in EU is 230V. so if there is a component that needs a 230V, in the US it will be connected between to 2 phases. Having said that, you might want at some point to connect another machine (power feeder?/light?/air compressor?), so a natural natural wire for that circuit might not be a bad idea. ?
Re: Electrical question Larry Long Neck All Messages By This Member #137103 FWIW my 2023 10kw Format4 profil z x-motion doesn't use a neutral. I'm not sure if the same motors and electronics are shared between their shapers and saws or not. toggle quoted message Show quoted text On Thu, Jul 25, 2024, 7:01?PM John Hinman via <jhinman1911=[email protected]> wrote: How do I confirm? ? The saw in question is a new Format4 KAPPA 450 X-motion.? ? -- John Hinman Boise ID K700S and A941 -- Larry Long Neck Just a noob trying to learn the ways of wood Making youtube videos now! -
Re: Electrical question John Hinman All Messages By This Member #137102 How do I confirm? ? The saw in question is a new Format4 KAPPA 450 X-motion.? ? -- John Hinman Boise ID K700S and A941
Re: Electrical question imran All Messages By This Member #137101 开云体育 I was curious about my old PP unit. The manual does not show a connection for the neutral. Not sure if same is true for the newer models. Neutral is not needed by the PP to produce 3 phase but it could be needed by a machine. Not a code expert, but I assume in such case neutral can be just passed through the PP unit. Imran Malik toggle quoted message Show quoted text On Jul 25, 2024, at 6:46?PM, Imran Malik <imranindiana@...> wrote: ?It is a valid question. A 3 phase machine can have a 120V single phase load and for that neutral would be required. I am not aware of any Felder saws that require neutral. Imran Malik On Jul 25, 2024, at 6:41?PM, John Hinman via groups.io <jhinman1911@...> wrote: ? I contacted an electrician to install my Phase Perfect, in preparation for a 5.5 KW 3-phase slider. ? He just asked me this question “Do you know if the table saw requires a neutral?” ? I have no idea- might someone help me out? ? As a follow-on question for the FOG, does this electrician’s question indicate that he does not know what he is doing? ? Thanks much! -- John Hinman Boise ID K700S and A941
Re: Electrical question imran All Messages By This Member #137100 开云体育 It is a valid question. A 3 phase machine can have a 120V single phase load and for that neutral would be required. I am not aware of any Felder saws that require neutral. Imran Malik toggle quoted message Show quoted text On Jul 25, 2024, at 6:41?PM, John Hinman via groups.io <jhinman1911@...> wrote: ? I contacted an electrician to install my Phase Perfect, in preparation for a 5.5 KW 3-phase slider. ? He just asked me this question “Do you know if the table saw requires a neutral?” ? I have no idea- might someone help me out? ? As a follow-on question for the FOG, does this electrician’s question indicate that he does not know what he is doing? ? Thanks much! -- John Hinman Boise ID K700S and A941
Electrical question John Hinman All Messages By This Member #137099 I contacted an electrician to install my Phase Perfect, in preparation for a 5.5 KW 3-phase slider. ? He just asked me this question “Do you know if the table saw requires a neutral?” ? I have no idea- might someone help me out? ? As a follow-on question for the FOG, does this electrician’s question indicate that he does not know what he is doing? ? Thanks much! -- John Hinman Boise ID K700S and A941
Re: Felder groove cutter inserts Chris Perren All Messages By This Member #137098 开云体育 How about a box of 10 for $180 from Felder?? ?Unless these are the wrong size… ? ? ? toggle quoted message Show quoted text From: [email protected] <[email protected]> On Behalf Of David Luckensmeyer via groups.io Sent: Tuesday, July 23, 2024 2:54 PM To: [email protected] Subject: Re: [FOG] Felder groove cutter inserts ? It is an odd size. When I bought replacements I tried my Leitz rep (Brisbane) and he could not source the cutters for any price. Felder had them in stock.? ? Warm regards, Lucky From: [email protected] <[email protected]> on behalf of David P. Best via groups.io <dbestworkshop@...> Sent: Wednesday, July 24, 2024 5:26:46 AM To: [email protected] <[email protected]> Subject: Re: [FOG] Felder groove cutter inserts ? The catalog for H3D tool Corp. lists 12 x 6 x 1.5 mm shaper cutter carbide inserts. You can reach them at this number: ?1-828-397-2467. ? I do not know if they stock them or what the price would be, but they do list them as an available choice in their catalog. ? Shars and Carbide Depot will both be dead ends as they cater to metalworking tools not woodworking. ?Leitz or C.G.G. Schmidt would be another logical choice to pursue. ?? ? David Best - via mobile phone? On Jul 23, 2024, at 12:30?AM, pjones8212 via groups.io <pjones8212@...> wrote: ? I have a k700s with the adjustable groove cutter set. I am in need of the main cutter inserts and felder has them listed for 43 for 2 before tax/shipping.... does anybody have an aftermarket source? The size in reference is 12x6x1.5mm thanks in advance.
Re: Felder groove cutter inserts David Luckensmeyer All Messages By This Member #137097 开云体育 It is an odd size. When I bought replacements I tried my Leitz rep (Brisbane) and he could not source the cutters for any price. Felder had them in stock.? Warm regards, Lucky toggle quoted message Show quoted text From: [email protected] <[email protected]> on behalf of David P. Best via groups.io <dbestworkshop@...> Sent: Wednesday, July 24, 2024 5:26:46 AM To: [email protected] <[email protected]> Subject: Re: [FOG] Felder groove cutter inserts ? The catalog for H3D tool Corp. lists 12 x 6 x 1.5 mm shaper cutter carbide inserts. You can reach them at this number: ?1-828-397-2467. ? I do not know if they stock them or what the price would be, but they do list them as an available choice in their catalog. ? Shars and Carbide Depot will both be dead ends as they cater to metalworking tools not woodworking. ?Leitz or C.G.G. Schmidt would be another logical choice to pursue. ?? David Best - via mobile phone? On Jul 23, 2024, at 12:30?AM, pjones8212 via groups.io <pjones8212@...> wrote: ? I have a k700s with the adjustable groove cutter set. I am in need of the main cutter inserts and felder has them listed for 43 for 2 before tax/shipping.... does anybody have an aftermarket source? The size in reference is 12x6x1.5mm thanks in advance.
Re: Felder groove cutter inserts David P. Best All Messages By This Member #137096 开云体育 The catalog for H3D tool Corp. lists 12 x 6 x 1.5 mm shaper cutter carbide inserts. You can reach them at this number: ?1-828-397-2467. ? I do not know if they stock them or what the price would be, but they do list them as an available choice in their catalog. ? Shars and Carbide Depot will both be dead ends as they cater to metalworking tools not woodworking. ?Leitz or C.G.G. Schmidt would be another logical choice to pursue. ?? David Best - via mobile phone? toggle quoted message Show quoted text On Jul 23, 2024, at 12:30?AM, pjones8212 via groups.io <pjones8212@...> wrote: ? I have a k700s with the adjustable groove cutter set. I am in need of the main cutter inserts and felder has them listed for 43 for 2 before tax/shipping.... does anybody have an aftermarket source? The size in reference is 12x6x1.5mm thanks in advance.
#forsale #forsale [email protected] All Messages By This Member #137095 Hi, for sale Phase Perfect Enterprise (not the entry level unit) in upgraded NEMA 3R outdoor enclosure and factory surge suppression. Low hours like new condition asking $4,500.? PTE015R-S, R in model number for NEMA and S for surge.? ? ? ? ? ? ? Jay Bowen Cleveland
Re: Felder groove cutter inserts mac campshure All Messages By This Member #137094 开云体育 So I’d say Shars is a dead end metalwork stuff look into leitz leiser Rengate Felder FS tool Schmidt on martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330?cell airtightclamps@... Designing and building for 50 years toggle quoted message Show quoted text On Jul 23, 2024, at 1:30?PM, Dan Gavrilyuk via groups.io <dgwoodco@...> wrote: ? Reach out to csp tooling via instagram, not sure if they have a website. They charge a fair price and probably have that size cutter in stock? On Jul 23, 2024, at 11:23?AM, Paul Jones via groups.io <pjones8212@...> wrote: ? The main cutters are a weird 12mm long by 6mm wide with 1.5mm thickness. I haven't been able to find them except on felder site and they are spendy... On Tue, Jul 23, 2024, 7:16?AM Jonathan Smith via <jonathan.smith=[email protected]> wrote: I have a Felder dado set that uses inserts. I have not looked into exact replacements but they look like typical inserts for tooling.? In the US, Shars is an import source for indexable inserts. ? There are lots of others. ? The nomenclature for inserts is standardized. You might find a number on the back side.? Happy hunting.
Re: Felder groove cutter inserts Dan Gavrilyuk All Messages By This Member #137093 开云体育 Reach out to csp tooling via instagram, not sure if they have a website. They charge a fair price and probably have that size cutter in stock? toggle quoted message Show quoted text On Jul 23, 2024, at 11:23?AM, Paul Jones via groups.io <pjones8212@...> wrote: ? The main cutters are a weird 12mm long by 6mm wide with 1.5mm thickness. I haven't been able to find them except on felder site and they are spendy... On Tue, Jul 23, 2024, 7:16?AM Jonathan Smith via <jonathan.smith=[email protected]> wrote: I have a Felder dado set that uses inserts. I have not looked into exact replacements but they look like typical inserts for tooling.? In the US, Shars is an import source for indexable inserts. ? There are lots of others. ? The nomenclature for inserts is standardized. You might find a number on the back side.? Happy hunting.
Re: Felder groove cutter inserts Paul Jones All Messages By This Member #137092 The main cutters are a weird 12mm long by 6mm wide with 1.5mm thickness. I haven't been able to find them except on felder site and they are spendy... On Tue, Jul 23, 2024, 7:16?AM Jonathan Smith via <jonathan.smith=[email protected]> wrote: toggle quoted message Show quoted text I have a Felder dado set that uses inserts. I have not looked into exact replacements but they look like typical inserts for tooling.? In the US, Shars is an import source for indexable inserts. ? There are lots of others. ? The nomenclature for inserts is standardized. You might find a number on the back side.? Happy hunting.
Re: Felder groove cutter inserts Jonathan Smith Member Profile All Messages By This Member #137091 I have a Felder dado set that uses inserts. I have not looked into exact replacements but they look like typical inserts for tooling.? In the US, Shars is an import source for indexable inserts. ? There are lots of others. ? The nomenclature for inserts is standardized. You might find a number on the back side.? Happy hunting.
Installing Felder Precision Miter unit with Pin Locating imran All Messages By This Member #137090 开云体育 Copied from my FB post: Received parts for what Felder calls "Precision Miter Unit with Pin Locating System". Installation was straight forward and can be done in 15 mins, just read the picture captions to get an idea. The Xcut fence now locks at 5 deg increments up to 45 degree with a special stop at 22.5 degrees. Felder missed an opportunity to make the calibration unnecessary. Any self respecting Felder owner really dials in the 90 deg stop, if Felder increased the length of the indexing bar by couple of inches and added a hole for 0 deg no calibration should be required. I will place the parts list in the files section in few days and also report on how well it actually works. Since there is no slop to speak of, I know that I can get it to at least give me 45 deg every time. That alone is worth the parts cost, under $300. See pics with captions here:

Imran Malik

Larry Long Neck