?

--

?

On Jul 29, 2021, at 8:53 AM, jbowen@... wrote:

?Hi Ed, your question is about blades but you mention interest in a K700 so I thought I would mention a Facebook marketplace post for a K700S that is a few months old. Seller is asking $11,500, located in WV. No affiliation with the seller.

https://www.facebook.com/marketplace/item/788095088424953/

On Jul 28, 2021, at 10:42 PM, ecohentoo@... wrote:

?Hi Folks, It's been decades since I last posted on a Felder group. Regretting yet another cumbersome shop move, with great remorse, I sold my Felder K700. Since then, I set up a new small home shop, bought small machines, including a 3hp SawStop. Don't get me wrong, I like this saw, but it ain't a Felder. Missing my old saw, I decided to bite the bullet and purchase a new K700 with all the stuff I want.
I know it will take a while to get my new Felder. Eventually, I most likely will sell the SawStop.

On a different note: I am interested in hearing what people have to say about combination blades and which ones they like. In the past, I liked my Ghudo, but have heard good things about Ridge Carbide. What do you think about Felder's own brand?

On Jul 28, 2021, at 7:39 PM, ecohentoo@... wrote:

Hi Folks, It's been decades since I last posted on a Felder group. Regretting yet another cumbersome shop move, with great remorse, I sold my Felder K700. Since then, I set up a new small home shop, bought small machines, including a 3hp SawStop. Don't get me wrong, I like this saw, but it ain't a Felder. Missing my old saw, I decided to bite the bullet and purchase a new K700 with all the stuff I want.
I know it will take a while to get my new Felder. Eventually, I most likely will sell the SawStop.

On a different note: I am interested in hearing what people have to say about combination blades and which ones they like. In the past, I liked my Ghudo, but have heard good things about Ridge Carbide. What do you think about Felder's own brand?

On Jul 28, 2021, at 4:53 PM, Joe Jensen <joe.jensen@...> wrote:

The instructions I received with mine are instructions for the saw blade lock.? Does anyone know if we are to do anything with the red flat blade screw?

?

From:?[email protected]?<[email protected]>?On Behalf Of?imranindiana via?
Sent:?Wednesday, July 28, 2021 1:46 PM
To:?[email protected]
Subject:?Re: [FOG] Red help with Felder Quick Lock

?

?Thanks to Michael Marsico, received?ProLock shaper spindle locking caps today. FWIW, there is an icon on top to indicate that the allen set/grub screw is the one to tighten.

?

<image001.jpg>

?

I did not know how this gizmo works. The split screw that is hand tightened has a dome shape on the underside.

<image002.jpg>

The cap has the negative profile. Once the screw is hand tightened I assume the two profiles marry/merge. Now as the allen grub screw is tightened the 2 halves of the screw spread. This should impart a downward force on the lower cap.

?

At least that is what I am theorizing after looking at it.

Imran

On Jul 27, 2021, at 7:22 PM, JP Rice via??<jprphotos@...> wrote:

?Thanks for the replies, it took a pair of pliers to break the knurled screw free, all is good now

On Jul 28, 2021, at 9:52 PM, Airtight: Clamps by Air Compression <airtightclamps@...> wrote:

?Tom I don’t know if any one mentioned this but if you have a 240 unit you can make a 240 outlet and power it wit two 120 plugs .?

Plug your saw into it for 240.

Mac,,,

martin/campshure/co/llc
mac campshure
7412 elmwood ave.
middleton, wi 53562-3106
608-332-2330?cell

airtightclamps@...

Designing and building for 50 years

On Jul 27, 2021, at 1:59 PM, bacchus6015 via groups.io <joeinno@...> wrote:

?Tom,

Have you considered a 240 volt portable battery set up? ?

Like this only 240 volts? ?

Chris Chan from Rangate helped me find an inverter to use with my battery powered stacker for when the power would go out in my shop so I could still open the garage door with the remote. ?There was plenty of power in the stacker battery pack but it would probably be too heavy to be portable. ?

Joe

On Jul 27, 2021, at 7:39 AM, tom@... wrote:

[Edited Message Follows]

Greetings!?

I had considered posting this in the Mafell forum, but I suspect there's a little more electrical aptitude here. I've been using a Mafell ERIKA 70 for several years now for my on-site work, and I just can't say enough good things about it. For those not familiar with the machines, this video gives a brief overview of pull-push saws:??They are sort of like a portable sliding saw, with the option to either rip or crosscut depending on how you configure it. Changing configurations only takes a couple seconds, and for crosscutting I've found it far more accurate than a miter saw.?

While I am trying to perform more work in my Shop, I think I am destined to spend a sizable portion of my career performing work on-site, so having a good portable solution is important.?

Anyways, with the recent minor facelift of the Erika line, Mafell has discontinued the 120V option on the Erika 70, leaving all of the Erika models now in only 240V. I believe that the machines destined for the NA market are 240V 60Hz, "stock" machines are 240V 50Hz. So, I'm going to jealously guard my 120V Erika 70, but I can see the writing on the walls, and was wondering what my options might be in the future should I either:
?1. Need to replace my Erika 70 120V with a Erika 70 or 85 240V 60Hz, or:
2. Acquire a Erika 60 240V 50Hz for those small jobs where the 70/85 is overkill

My requirements are:
- Need to be able to work on-site in residential settings, with access only to 120V 60hz power.

- Needs to supply 240V 60Hz (50Hz would be nice for the Erika 60), the Erika 85 draws 2,500 watts, the Erika 60 draws 1,300 watts

- Needs to be a portable solution (preferably <40 lbs)

- Needs to be a solution that is weather tolerant (needs to be able to handle snow, drizzle, heat, cold, etc.....)

- If it’s a battery solution, I can charge 240V in my Shop overnight

- I am usually able to prep most of my materials ahead of time in my Shop, so the on-site work is mostly ripping and trimming cuts. This is a low-volume, one-person show, so not terribly intensive use

I suppose the simplest solution would be something like the Festool Sys-Powerstation??, but I wonder if there are portable step-up transformers or "hardened" VFD solutions? In terms of the Festool Sys-Powerstation, I wonder if anybody would be willing to work with me to get a 240V model imported to NA (please message me privately for this). Or, am I simply out of luck and need to start going with the flow, reverting back to a miter saw and table saw (say it ain't so!!)??

Anyways, I know there's a lot of creativity here, and would be curious what thoughts folks might have. Thank you in advance for any tips or advice.....?

(Edit: clarified requirements)?

--
Tom Gensmer
Heritage Home Renewals, LLC
Minneapolis, MN

On Jul 27, 2021, at 1:59 PM, bacchus6015 via groups.io <joeinno@...> wrote:

?Tom,

Have you considered a 240 volt portable battery set up? ?

Like this only 240 volts? ?

Chris Chan from Rangate helped me find an inverter to use with my battery powered stacker for when the power would go out in my shop so I could still open the garage door with the remote. ?There was plenty of power in the stacker battery pack but it would probably be too heavy to be portable. ?

Joe

On Jul 27, 2021, at 7:39 AM, tom@... wrote:

[Edited Message Follows]

Greetings!?

I had considered posting this in the Mafell forum, but I suspect there's a little more electrical aptitude here. I've been using a Mafell ERIKA 70 for several years now for my on-site work, and I just can't say enough good things about it. For those not familiar with the machines, this video gives a brief overview of pull-push saws:??They are sort of like a portable sliding saw, with the option to either rip or crosscut depending on how you configure it. Changing configurations only takes a couple seconds, and for crosscutting I've found it far more accurate than a miter saw.?

While I am trying to perform more work in my Shop, I think I am destined to spend a sizable portion of my career performing work on-site, so having a good portable solution is important.?

Anyways, with the recent minor facelift of the Erika line, Mafell has discontinued the 120V option on the Erika 70, leaving all of the Erika models now in only 240V. I believe that the machines destined for the NA market are 240V 60Hz, "stock" machines are 240V 50Hz. So, I'm going to jealously guard my 120V Erika 70, but I can see the writing on the walls, and was wondering what my options might be in the future should I either:
?1. Need to replace my Erika 70 120V with a Erika 70 or 85 240V 60Hz, or:
2. Acquire a Erika 60 240V 50Hz for those small jobs where the 70/85 is overkill

My requirements are:
- Need to be able to work on-site in residential settings, with access only to 120V 60hz power.

- Needs to supply 240V 60Hz (50Hz would be nice for the Erika 60), the Erika 85 draws 2,500 watts, the Erika 60 draws 1,300 watts

- Needs to be a portable solution (preferably <40 lbs)

- Needs to be a solution that is weather tolerant (needs to be able to handle snow, drizzle, heat, cold, etc.....)

- If it’s a battery solution, I can charge 240V in my Shop overnight

- I am usually able to prep most of my materials ahead of time in my Shop, so the on-site work is mostly ripping and trimming cuts. This is a low-volume, one-person show, so not terribly intensive use

I suppose the simplest solution would be something like the Festool Sys-Powerstation??, but I wonder if there are portable step-up transformers or "hardened" VFD solutions? In terms of the Festool Sys-Powerstation, I wonder if anybody would be willing to work with me to get a 240V model imported to NA (please message me privately for this). Or, am I simply out of luck and need to start going with the flow, reverting back to a miter saw and table saw (say it ain't so!!)??

Anyways, I know there's a lot of creativity here, and would be curious what thoughts folks might have. Thank you in advance for any tips or advice.....?

(Edit: clarified requirements)?

--
Tom Gensmer
Heritage Home Renewals, LLC
Minneapolis, MN

On Jul 28, 2021, at 10:02 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:

This happen all the time with me.

But each time it's because I didn't give that little red knob a twist
to release it. I'm sure you checked that.

On 7/28/21 5:19 PM, mike krockford wrote:
Nobody has an insight? Seems like a common problem...

On Jul 27, 2021, at 6:07 PM, mike krockford via groups.io <mcrockford@...> wrote:

Hi all. Probably simple fo someone who knows more than I do:

Over the years, occasionally I’d turn off the saw with the small red button (not the emergency twist knob ) and then the saw wouldn’t start up again for several tries. I’d blow out or suction out the dust and it’d then start up. Inconclusive whether dust was the cause.

Well this time, that protocol didn’t work. I opened up both switches, checked connections, blew out dust, untwisted the wire (shown in photo). No luck.

The power from the main cutoff is there - hums until warmed up, indicating ready to go.

I opened up the main panel, blew out the minor dust, traced the power and switch wires to various terminals, and made sure those wires were tight.

I pressed all the fuse buttons (I assume they’re fuse buttons) to “reset” them. The black ones depress, the red ones do not.


Still no power to the saw.

Anyone know what’s going on here, or what I can do myself?

Alternatively, anyone know a tech in central jersey that could come fix it? I have the wiring diagrams although they’re confusing to me.

Thanks
Mike
General Idea





<image4.jpeg>
<image3.jpeg>
<image2.jpeg>
<image1.jpeg>

Nobody has an insight? Seems like a common problem...

On Jul 27, 2021, at 6:07 PM, mike krockford via groups.io <mcrockford@...> wrote:

Hi all. Probably simple fo someone who knows more than I do:

Over the years, occasionally I’d turn off the saw with the small red button (not the emergency twist knob ) and then the saw wouldn’t start up again for several tries. I’d blow out or suction out the dust and it’d then start up. Inconclusive whether dust was the cause.

Well this time, that protocol didn’t work. I opened up both switches, checked connections, blew out dust, untwisted the wire (shown in photo). No luck.

The power from the main cutoff is there - hums until warmed up, indicating ready to go.

I opened up the main panel, blew out the minor dust, traced the power and switch wires to various terminals, and made sure those wires were tight.

I pressed all the fuse buttons (I assume they’re fuse buttons) to “reset” them. The black ones depress, the red ones do not.


Still no power to the saw.

Anyone know what’s going on here, or what I can do myself?

Alternatively, anyone know a tech in central jersey that could come fix it? I have the wiring diagrams although they’re confusing to me.

Thanks
Mike
General Idea





<image4.jpeg>
<image3.jpeg>
<image2.jpeg>
<image1.jpeg>