Re: Hammer C31 Dust Collection piping setup
#hammer
I sourced all standard fittings from Air Handling ? There are others but these guys had an organized website, decent prices and were responsive to emails and phone calls.? I sourced spiral pipe and custom fittings from a local hvac shop.? Nordfab, thru marketing, has made their name synonymous with clamp pipe systems and so gets a premium price for standard materials.? It's nice looking stuff but there are other sources.?
|
Re: Shaper with CopeCrafter and outboard fence and pressure jaws to make panels
Having just received an F900z, I'm very intrigued by this thread. In general, is a copecrafter type sled more desirable than using the sliding table, or a substitute for those with machines without a slider, or just depends on your personal preferences? Thanks to this thread, I've found my way to the Mac clamps for consideration. What of the Big Squeeze? As? a newbie here, I'm slowly catching on - are these air clamps developed by a member/for members???Just getting started, so this would be a key in helping me develop my procedures in coping for cab doors. Welcome clarification from anyone willing to fill me in.?
Jeff
|
Thanks everyone for the suggestions.? I really appreciate it.? The Michael Fortune looks comfy with the concave back and seat but missing the wide flat arms to hold beverages.? The Andy Rae has arms but a flat seat and back.? Cliff's solves both problems as well as the arm connection.? I like how they are low to the ground.??
We have some black locus around here.? I know it makes for rot resistant fence posts. Its strong so could make thin slats from it.? Good idea if I can source it.? Thanks.
See you Tuesday Mark.
|
Many thanks for taking time to respond and attach pdf, Allen. You say you "Just need to separate the machines ...." I presume I merely need to locate a few attaching bolts and pull .. Are the cables long enough to permit the necessary working gap of a few inches or is there more involved?
Thanks again,
Steve
|
Re: Hoffman Key Router $250 - 20mins left
I have this machine. It is fabulous. I bought it for a specific job which was supposed to be a regular batch production run situation. That didn't come to fruition and it largely sits collecting dust. If anybody is interested I could probably be talked into selling it. Jason Holtz
J. Holtz Furniture
3307 Snelling Ave. South Minneapolis, MN 55406
612 432-2765 -- Jason J. Holtz Furniture 3307 Snelling Ave. South Minneapolis, MN 55406
|
Re: Hammer C31 Dust Collection piping setup
#hammer
Thanks! this is awesome and just the understanding I needed.? Can I ask how long your hose is for the drop? 10ft?? Also how high is your joint from the floor?
Thanks again!
-- Drew Tosh Designer / Owner
, LLC.
413 S Frontier Ln Cedar Park, TX 78613
Main: 512-553-9663 Mobile: 512-971-7406
|
Re: Hammer C31 Dust Collection piping setup
#hammer
Thanks! ?I also need to expand my system so those prices really help!!!
toggle quoted message
Show quoted text
Blast Gate Company sells Nordfab-compatible ductwork (most of mine is from there), including 5" ball joints:
|
I’m currently using a Clearvue CV1800 which was great until I added the AD941 and started using it for planing. It just creates to many chips for the cyclone to gravity dumb into my 55 gallon barrel. Anyone use a small airlock on their extractor or have any other suggestions on dealing with the chipload?
|
Re: Hammer C31 Dust Collection piping setup
#hammer
Blast Gate Company sells Nordfab-compatible ductwork (most of mine is from there), including 5" ball joints: https://blastgateco.com/Clamp-Together/CT-Floor-Sweeps-Ball-Joints.php
|
Re: Hammer C31 Dust Collection piping setup
#hammer
You might try Air Handling Systems. The do custom sizes and connectors.
toggle quoted message
Show quoted text
On Jun 1, 2021, at 2:15 PM, Brian Lamb < blamb11@...> wrote:
Rockler lists it on their page for $200 for the 5”,?
?
and then I went to the Nordfab site (might be a partner):
?
and they have it listed for $250 for a 5”, part number 3209-0500-10000
Google search worked….
Thanks Brian. ?Looked and found a “ball joint” from Nordfab but it is only available in even duct sizes. ?Based on the 120mm outlet of my RL, I sized my ducts for 5”, so no luck there… On Jun 1, 2021, at 12:15 PM, Brian Lamb < blamb11@...> wrote:
They make ball swivels…. not sure about Nordfab, but plenty of others...
You got me all excited there. ?I read “swivel” then went to the Nordfab catalogue to look for said coupling. ?Upon rereading your message, I see the swivel is obtained by loosening a clamp. ?Bummer. ?
Pipe and hose can be mounted overhead.? For a multi function the Y piece swivels on a loosened clamp to keep the hose(s) out of the way.???<20200202_110454.jpg><20200202_110727.jpg><20200202_110900.jpg><20200202_111545.jpg><20200202_112839.jpg>
|
Re: Hoffman Key Router $250 - 20mins left
MY new best known method is to either hire a professional rigger and direct ship (expensive) or travel and get myself.
?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]>
On Behalf Of Michael Garrison Stuber
Sent: Tuesday, June 1, 2021 12:56 PM
To: [email protected]
Subject: Re: [FOG] Hoffman Key Router $250 - 20mins left
?
Maybe.? Entirely depends on whether it survives crating and shipping . . .
--
Michael Garrison Stuber
On 6/1/2021 12:49 PM, habacomike via groups.io wrote:
Went for 1,050. ?I started looking through the stuff there — a veneer saw sold for $950? ?What a steal…
?
?
I surely thought this will go up but still at $250.
?
--
Michael Garrison Stuber
|
On Tue, Jun 01, 2021 at 11:58:11AM -0700, pat_steveking via groups.io wrote:
| Any 'how-to' advice or tips would be very much appreciated!
Assuming your 2003 is like my 2004, it's straightforward. I've attached the relevant page from my parts book. You just need to separate the machines, unhook the chain and hold it aside using a clamp or similar (so it's easier to reinstall it later), remove bolt #49 and all the parts outboard of the wheel, replace the wheel, and then reverse your steps. It'll be clear once you have a good look at it. Separating the machines is definitely the most annoying part of the job.
Allen
|
Re: Hammer C31 Dust Collection piping setup
#hammer
Rockler lists it on their page for $200 for the 5”,?
?
and then I went to the Nordfab site (might be a partner):
?
and they have it listed for $250 for a 5”, part number 3209-0500-10000
toggle quoted message
Show quoted text
Thanks Brian. ?Looked and found a “ball joint” from Nordfab but it is only available in even duct sizes. ?Based on the 120mm outlet of my RL, I sized my ducts for 5”, so no luck there… On Jun 1, 2021, at 12:15 PM, Brian Lamb < blamb11@...> wrote:
They make ball swivels…. not sure about Nordfab, but plenty of others...
You got me all excited there. ?I read “swivel” then went to the Nordfab catalogue to look for said coupling. ?Upon rereading your message, I see the swivel is obtained by loosening a clamp. ?Bummer. ?
Pipe and hose can be mounted overhead.? For a multi function the Y piece swivels on a loosened clamp to keep the hose(s) out of the way.??
<20200202_110454.jpg><20200202_110727.jpg><20200202_110900.jpg><20200202_111545.jpg><20200202_112839.jpg>
|
Cliff,
At age 72, I know what you mean. I sat in an Andy Rae chair at MASW, and thought that it was more comfortable than most. It would be more so if curves were added. The Michael Fortune garden chair is curved and very comfortable, but with the bent laminations, more of a challenge to build.
Steve
toggle quoted message
Show quoted text
On Jun 1, 2021, at 1:01 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:
On 6/1/21 1:56 PM, Steve Hubbard wrote:
Andy Rae
I considered that lay out and rejected it. Ya kind of have to use
cushions with all those flat lines. That or a 20 something body.
|
Re: Hoffman Key Router $250 - 20mins left
Maybe.? Entirely depends on whether it survives crating and
shipping . . .
--
Michael Garrison Stuber
On 6/1/2021 12:49 PM, habacomike via
groups.io wrote:
Went for 1,050. ?I started looking through the stuff there — a
veneer saw sold for $950? ?What a steal…
I surely thought this will go up but still
at $250.
--
Michael Garrison Stuber
|
Re: Hoffman Key Router $250 - 20mins left
Went for 1,050. ?I started looking through the stuff there — a veneer saw sold for $950? ?What a steal…
toggle quoted message
Show quoted text
I surely thought this will go up but still at $250.
|
Re: Hammer C31 Dust Collection piping setup
#hammer
Thanks Brian. ?Looked and found a “ball joint” from Nordfab but it is only available in even duct sizes. ?Based on the 120mm outlet of my RL, I sized my ducts for 5”, so no luck there…
toggle quoted message
Show quoted text
On Jun 1, 2021, at 12:15 PM, Brian Lamb < blamb11@...> wrote:
They make ball swivels…. not sure about Nordfab, but plenty of others...
You got me all excited there. ?I read “swivel” then went to the Nordfab catalogue to look for said coupling. ?Upon rereading your message, I see the swivel is obtained by loosening a clamp. ?Bummer. ?
Pipe and hose can be mounted overhead.? For a multi function the Y piece swivels on a loosened clamp to keep the hose(s) out of the way.??
<20200202_110454.jpg><20200202_110727.jpg><20200202_110900.jpg><20200202_111545.jpg><20200202_112839.jpg>
|
Re: Hoffman Key Router $250 - 20mins left
Thanks - I missed this and would like a slower one of this
Get
toggle quoted message
Show quoted text
I surely thought this will go up but still at $250.
|
Good evening,
I have a 2003 model CF731 combination machine. It looks as if urethane hungry animals have been eating the rim of the friction wheel of my Felder. Has anyone any experience of getting at - and replacing - the friction wheel on these machines? Presumably the process will involve splitting the jointer/thicknesser from the saw/spindle unit. Any 'how-to' advice or tips would be very much appreciated!
Many thanks,
Steve.
|
Hoffman Key Router $250 - 20mins left
I surely thought this will go up but still at $250.
|
Jonathan Smith
Jason Holtz
Drew Tosh
Joe Jensen
Allen Akin
imran