开云体育

Ok I can weigh in here. I just built a new shop, roughly the same size as yours, and I had to include an office in it. Originally i was thinking the same as you. I know my real passion is in the shop

I installed an electrical outlet in the chassis of my KF700. Mounted inside the chassis the outlet sits flush with the outer surface of the chassis. Let me know if you would like a picture. Imran

The lower doors have a full sheet of MDO on outside and inside faces. Upper doors use a single sheet outside and inside face. I had to reskin left side lower door in 2016 because of neglect. In place

Hook up to machine power they draw squat. recently set up a feeder to my Gomad shaper. Used machine power. I have a light start stop button so I can run by itself, but if I have to hit stop for shaper

Mine is wired into the same feed as the saw. Brian Lamb blamb11@... www.lambtoolworks.com

I spent 40 years in offices about 10’ x 10’. That provides room for a desk, file cabinet, layout table, bookshelves, and space for a visitor to sit. Used to keep a drafting table with parallel

I finally received the tilting device for my power feeder last week. I had to grind a bit of the metal to allow one of the sides to fit into rail on the machine (I am surprised how poorly milled one

My office will be a little bigger at 18x18' but it will be separated from the rest of the building by a tight door so dust will stay out, which means I can use it as a finishing room (I don't

My shop is basically a cube: 10’ x 11’ w/10’ ceiling. It also serves as the primary entrance for my shop (left side of pic) the ‘corridor’ down the left side makes the tiny space feel a

Mac, LOL Thanks my friend! I don't know any sheep farmers :) *Scott Glaser* *6627 Dolan Falls* *Flower Mound, TX 76226* *sjglaser1@... <sjglaser1@...>* *945-444-8066* [email protected]>

12 x 12 would be my suggestion. Brian Lamb blamb11@... www.lambtoolworks.com

Thanks James for the refresher. So the seal saturates instead of drying up ? Imran Malik https://www.facebook.com/groups/362481112015700/?ref=share

John, It is about 193 USD from https://www.scosarg.com/cmt-230-dao-pro-saw-blade-set-d-203-b-30mm-z12-atb in the UK. Not sure about the shipping cost to the US though. James

It is under $200 (?154) at S&S, probably $300 shipped to USA. Shipping was $60 pre pandemic for my dado. Imran Malik https://www.facebook.com/groups/362481112015700/?ref=share

Yes, it happened to my F48 after leaving it upside down for 5 years. Here below is the response from Felder Mississauga. Now I put the power feeder upright when not in use. It is ONE MORE PAIN of KF

It was for sale in Norway but they ship to the US. $375 for the 30mm bore set shipped to the US. They only have 1 set in stock.

I will also mention I had a led dock light and it was mediocre light quality but cheap and easy. Good enough for machine work. Not good enough for sub mm hand tool work.

I looked into medical lights and didn’t like what I found for cost. Several thousand bucks, which is ok but I wanted a light I could use across the shop to help my aging eyes with joinery and hand

Guys, I have been lucky with no leaks on vario4 when it was upside down on tilt bracket for many yrs. However, some have reported leaks here (IIRC, F48) due to the seal drying up during storage. Imran

Hello, I know if 10 people answer, I'll get 20 answers to my below question with probably a fair number saying it depends. But, I'll ask anyway. I am adding 1200 sq. ft. onto my existing 1750 sq. ft.