开云体育

Everything is working now. I think I had some switch set somewhere on the radio. I got my Baofeng UV5r/Pi/Direwolf/Xastir iGate working. Then I reset the 878 to factory settings and load an old

copy that, thanks, so no alsa-soft-preamp then??? There's many .asoundrc examples, with people getting 120% volume, but none of them seem to work in my implementation. I'm using the 1200baud output

Hey Ray, Ok. It would be good to figure this out as Direwolf shouldn't give errors like that. Ps. When using Dirwolf for general AX25 duties and not specific APRS duties, you should disable it's APRS

I assume you're looking to do 9600bps or faster FSK packet. If not, you should not use the "9600 baud" or discriminator port as your signals need the pre-emphassis/de-emphassis for standard 1200bps

BPQ32 doesn't do TNC duties.. it's Direwolf that does that. If BPQ32 needs to send something, it would send that detail via (in your case), the AGW port and Direwolf would key up your radio and send

I started using an "Audio Injector Z" audio hat with a Pi which has a -6dB hardware cut on the Line-In. The line/discriminator output of my Yaesu ftm400 is not adjustable, so levels are low on

David I have kernel AX25 compiled on the Direwolf machine but not configured. Given a few days I can do that and attempt to get a sample of the audio. Further to my thought that AISAT may have been

Hi. I have one IC-910 V/U scanning both bands via CI-V on BPQ32. How i can PTT direwolf from BPQ? BQP is connected to direwolf via AGW port. Normally with Ardop or Vara i configure the port with the

I have changed some setting somewhere on the 878 and now it isn't sending packets.

Hello Rick, Interesting.. would it be possible for you to capture the audio of one of these packets into a WAV file and send it to the list? Alternatively, if you have a full Linux AX.25 setup, could

Hello Brian, I assume that's auto-correct helping you out there and you meant to say "plughw:2,0" right? There is something wrong here as you really shouldn't need that amount of gain. If I was to

It is a requested enhancemt. wrote:

Just a thought:In your printout, Direwolf clearly determines the packet is NOT AX.25 (line 2), but still sends it through the AX.25 interpreter - probably the default for unknown packet types.? Since

Dear all, Is it possible to configure direwolf for multimode? I mean is it possible to have more than one modem speed configured for the same radio channel, i.e. audio card/trx ? tnx, Roland --

On 11/8/21 1:21 pm, Rick Hatton wrote: I am using an Anytone 878 as an APRS transmitter, and Direwolf/Xastir on 2 computers. When the 878 transmits APRS packets, I get this error from Direwolf on both

I am using an Anytone 878 as an APRS transmitter, and Direwolf/Xastir on 2 computers. When the 878 transmits APRS packets, I get this error from Direwolf on both receiving machines: Internal error

Sam, Thanks for the help. It appears the config you are reccomending is not resolving my issue. David, I checked the manual -

I don't mean to lead people away from a supported configuration.? This interested me as I went through a lot of the same trouble in the past and I had a need to run multiple "listeners" at the same

As for disabling the onboard device, yes; that is where I disabled mine as well...just to remove confusion later. -Sam KO4HBY

Perhaps it is better illustrated by sharing my config instead (with my call removed).? Notice the single pulse under the audio device line.? The second instance is redundant if it is the same