开云体育

A more specific thread on this DINAH issue which is probably wired similar to your Pi HAT: /g/DINAH/topic/sqelch_open_attached_to/91808019 --David KI6ZHD

Hello Arnold, Please try NOT specifying a specific number: sudo alsactl store Once that's run, make sure you have the following file present with today's date/time: sudo ls -la

Hello Grayson, If you stop Direwolf from running, can you increase the playback volume via alsamixer and it will STAY up? Btw.. here are various messages from the Direwolf archives about

David, I have used sudo alsactl save , but put in the port number to also try. systemctl | grep alsa does respond with "loaded active exited" The only thing in /etc/alsa/ is a directory conf.d .

Once I start the pi I can increase the volume but after trying to transmit it is constantly lowered to zero even in alsamixer if I hold the up arrow it keeps getting turned down. I will try contacting

Hello Grayson, Does the audio go down to zero every time Direwolf tries to transmit? If it goes down to zero, can you try INCREASING the audio level in alsamixer and then wait for Direwolf to

This is a "real" Shari it was ordered from Kits4Hams, my PTT config is just PTT CM108, and trying to transmit lowered the volume a couple of steps then jumped to zero at the end. Grayson

Few more questions / ideas: - Is this a "real" Shari board or a clone? /g/SHARI/message/2902? - In your direwolf.conf file, what have you configured for the PTT line? -

I'm using a SHARI Pi hat MOD2 on a PI4 that's CM108, I did try making the changes in alsamixer but it still lowers after trying to transmit. Grayson

What sound device are you using? There are some known issues with say early versions of the Digirig where the key up signal would lower the output audio levels, etc. The Direwolf User Guide does a

I'm having an issue with getting data to send with Direwolf 1.7 on a Raspberry Pi with Bookworm. It can receive fine and PTT activates when a message should be sent but it's only the carrier and no

One addition here: back on 11/11/23, I had updated my https://www.trinityos.com/HAM/CentosDigitalModes/RPi/rpi-setup.html doc to include an addition command line option: sudo alsactl --no-ucm

Hello Arnold, Raspberry Pi OS Bookworm uses systemd and it should have already installed the following Systemd unit files to restore your saved audio levels via:

I too have found this to be an issue with bookworm while running Direwolf 1.7. My guess is that this will also work with 1.8. My workaround was to install pule audio then install pauvcontrol sudo

Greetings Arnold. After <F6> and choosing the correct sound card before making adjustments, then <Esc> to exit, did you "sudo alsactl store"? Your Rpi may have several audio devces, so <F6> to choose

David, Yes, it is Raspberry Pi OS, Bookworm. Looks like I didn't use "alsastl restore". Where should this go? I didn't look for /var/lib/alsa/asound.state file yet, but I'll try Restore first.

Hello Arnold, I assume you're using Raspberry Pi OS correct? In your direwolf.conf file, what sound devices are you using via your various specified ADEVICEs? Few things to check: - does the

I have Direwolf working in a Pi 3B, and I am unable to have the sound devices volumes get properly restored after a reboot. It receives fine, and transmits fine, and I can adjust volumes easily using

I use a Pi 2 (?) the first iteration anyway. I am running a 2 way internet gateway without issue. [email protected]> wrote:

I've never been in a hurry do get things done properly, but thanks for the reminder. I use either a Pi 3 or Zero 2W. They are plenty fast. The slowest part is usually downloading over whatever