开云体育

Thanks for the follow-up. What VNC server were you using previously? 73, Lee K5DAT

Hi, Mystery solved. The 'sendto=IG' option was missing from the 'PBEACON' configuration line. Interestingly, Direwolf on Windows was missing that option too but was able to send the updates

Hello everyone, To follow up on my little resolution problem, now I use "tightvncserver" and it works well I'm in: unencrypted connection in SSH mode: sudo apt-get install tightvncserver And it works

Thank you for your clever answers and help, I will read all of them slowly and check the different options shown. By the moment, I am using a FT-817ND (which is the one I like to free for SOTA) and

Hello Mau, Are you saying that the Direwolf logs from both Windows and LInux are effectively identical? If so, that would be strange. For the "Audio Input level too high" issue, how are you connecting

I can't say much about the logs, but the "Audio input is too high" message can be fixed by either: Reduce the output (speaker of Audio-out) of the radio - volume control if setup that way, or resistor

Hi, I have Direwolf 1.6 running on Ubuntu (with rtl_fm) compiled and installed from source. Same version on Windows iGate configuration is an identical copy&paste for both OS On Windows I see this log

Thank you all, in fact I was trying packet in connected mode at 9600 baud, and it did not work. Then I discovered that one radio had the tones on. When I put it off I got connection, However I did not

He wasn’t asking specifically about APRS, DireWolf is also used for connected packet extensively these days. Brian N2KGC Sent: Thursday, August 10, 2023 10:50 AM To: [email protected] Subject: Re:

Using PL tones on the the1200bps AFSK modulation version of APRS not only works but is apart of the specification called "Voice Alert": http://www.aprs.org/VoiceAlert3.html I've never read about it

Yes, you are right, when transmitting APRS, you should not use any subtone, as this cause disruption on the modulated 1200 or 9600 baud tone that are use to transmit the APRS signal.

Hello folks, can you confirm that transmitting sub audio tones will spoil the communication, at least at 9600 baud? That's what I found and is probably well known. 73 Giovanni IZ5PQT

That is indicating your radio heard a message not addressed to you (other message). There should be an aprs menu option for disabling other message pop-ups on the FT5. 73, Brent WG0A

From time to time I get a pop up on my FT5 from my direwolf igate/DiGi that has OM>(callsign) It won’t log to my station list or message list on the radio. What is this? Is there a way to filter

I assume the attached pictures do not show the whole screen. If that is the case, then I suspect the issue is on the VNCViewer side. Have you checked your settings on the computer you are connecting

Good evening to you, I ran tvservice -o and it doesn't work? Luc Drolet VE2 LUQ Président de VE2CVA C.R.A.V.A. Club Radio Amateur Vallée de l'Amiante VE2 CVA ve2cva@... ldrolet@...

I have a fix-video script that runs tvservice or vcgencmd as needed/pi0 vs pi3/4 Example: tvservice -o For off...-p for preset see man pages Example: vcgencmd display_power 1 2 vcgencmd

Hi Robert, even after my reboot I still have a small screen ? ? End reboot Luc Drolet VE2 LUQ Président de VE2CVA C.R.A.V.A. Club Radio Amateur Vallée de l'Amiante VE2 CVA ve2cva@...

First, run?? ~ $ cat /proc/version it should display something like:Linux version 6.1.21-v8+ (dom@buildbot) (aarch64-linux-gnu-gcc-8 (Ubuntu/Linaro 8.4.0-3ubuntu1) 8.4.0, GNU ld (GNU Binutils for

Good evening Robert, Yes I can use SSH mode here is what I got with it: vncserver -geometry 1280x1024? Luc Drolet VE2 LUQ Président de VE2CVA C.R.A.V.A. Club Radio Amateur Vallée de l'Amiante VE2