开云体育

By the time you looked, I had removed the filtering and the IGTXVIA 0 has been commented out. When I looked at the Screen for direwolf, it was constantly scrolling with stuff for the IGate to

Hey Arnold, Looking at this T2ONATARIO server by going to http://status.aprs2.net/ then doing a search for "T2ONTARIO", clicking on that to take you to http://72.38.114.30:14501/ . At the top of this

I'm seeing odd behavior on a couple of IGates. Occasionally in the last couple days they are being sent thousands of packets to be "transmitted" as if they are suddenly receiving a full APRS feed. For

Fixed, Thanks for the clues. I switched off the pre amp in my radio and that seemed to fix it. I am new and learning. I was using SSB earlier and trying the different functions. Jeff Sent: Thursday,

Hi David, Thanks for the attention. I am pretty much using the default configuration files for direwolf. In that, the line for FIX_BITS is commented out. As far as the radio interface, I am directly

+1 for the comment about audio bandwidth. To me, the signal sounded "funny" when played in Audacity, and John's comment about audio bandwidth - I'd call it audio "strangling" - took me back to the

Let's take a look at it with Audacity. This is what it should look like. (test1.wav) The spectrum should be similar to this. Most of the energy in roughly the 1200 - 2200 Hz range. This is what you

Hello Jeff, What is your direwolf configuration in terms of your demodulator settings, FIX_BITS, etc? As you can see below, the top file is the test1 file and the bottom one is the jem1 file. Few

Hi, I have been tracking down a problem with direwolf and have narrowed it down to the sound input file.? I saw this problem on both a raspberri pi and a pc. I have tested both version 1.7 and 1.6

All things seem to be working elsewhere. I can key the radio through the Bluetooth with PAT to make a 10 meter connection. I had direwolf working with Xastir through a CAT cable but I do not have the

Setting up bluetooth serial ports on a Raspberry Pi is possible but takes some work (maybe some 25 steps or so). I assume you have the Linux rfcomm interface fully working on one side (paired,

Hello, I just replaced my CAT cable from my pi to my Yaesu 857 with Bluetooth CAT control. I can not figure out what the correct syntax is in direwolf for PTT. Everything else with the Bluetooth CAT

Hello Herber, If running this script from the command line WORKS but from cron does not, this isn't a make/model issue of your particular SDR. Something else is wrong. It should be mentioned that

John Did try this option and had a whole different problems, I am going to blame it probably in the SDR type I am using. Waiting for another brand I order to see if this could be resolved. Gracias

John So just install the Rapian Lite image and instead of compiling Direwolf just run: apt install direwolf Gracias Heber NP4JN 73 Sent: Wednesday, April 21, 2021 10:39 AM To:

I've had better luck using the Direwolf apt package in Raspbian.... It installs Direwolf 1.6 and starts it as a service with systemd. Never had any issues with it not starting that way.

It runs pretty fast, nothing on the screen when “screen -r” issue. Don’t know if has to do with the SDR I am using (NESDR SMART), order a different one to test ran out of options. I have

Hello Herber, It seems you're system is successfully restarting the Direwolf but it's happening a LOT. I'm surprised there isn't any details here. If you connect to the screen session, do you see

This are the last entries in the log ----------------------- Mon 19 Apr 17:09:43 BST 2021 Direwolf in CLI mode start up No Sockets found in /run/screen/S-pi. ----------------------- Mon 19 Apr

I think what you want is FILTER 0 0 ! d/callsign Patrick (N3TSZ)