开云体育

Hello John, If you research the archives here and many other forums, you'll find a LOT of other users having lots of different issues including: - inconsistent input and output audio levels during

Hi, If I can get them working A-OK, I'll stick with them. Once STE was disabled, I ran several tests and I'm getting no missed packets. Not sure how it will fare when it's plugged into an X-30, but

They may be low quality.... But you just solved your problem, and effectively showed that all the "Baofeng is garbage and doesn't work for packet" was far more unfounded bias against what is seen as

That's not the case here - radios based on the RDA1846(S) chips have a feature that uses a CTCSS tone to signal end of transmission, so compatible radios can mute the receiver and avoid the squelch

Reduce power, the RF is get induced to the PTT keeping TX too long. 73 de Yono - YD0NXX

Hi, It was on by default. I didn't know it was there to switch on hehehe Mat. Cheers Dana, that was it!!! Disabling STE cured it :) I Feel a bit of a fool for not spotting that in the manual :) I will

I believe this is a feature of the RDA1846 and not unique to Baofeng; it's up to the firmware developer of each radio to set the default state for this. If I recall correctly, I discovered this in a

Hello Matt, Curious, was this Baofeng feature ON by default or did you turn it on? --David KI6ZHD

Hi, Cheers Dana, that was it!!! Disabling STE cured it :) I Feel a bit of a fool for not spotting that in the manual :) I will take the advice about Baofeng being rubbish (they are, I get quite bad

Have you made sure to disable "Squelch Tail Elimination" on the radio ? https://ham.stackexchange.com/a/3807 It may be enabled by default. 73, Dana? K6JQ

Hi, I don't have the PTT-ID enabled but cheers for the heads up. It's quite ironic that my main rig is a FT911-A (that's doing just fine) , but I can't dedicate that for my packet node. Cheers, Mat.

Hi, I agree with what your both saying, but I'm setting up a node that will probably never get used (so I can learn). I'm in the UK so there is not the enthusiasm for packet that you are accustomed to

Please review the archives about all kinds of issues with using Baofeng radios with packet radio. There was a very recent post where one person just swapped out his Baofeng radio and all of his issues

You're running into one of numerous, and somewhat unpredictable, timing issues with the Baofeng radio. They are not suitable for packet radio, find a used "brand name" radio and use that instead. I

If you do a little research you find the Baofeng is not a good radio for packet, you can probably find a older/used radio with the packet connector which will serve you much better. -- John D. Hays

Hi, I'm a packet newbie and I've got direwolf working (have to say, the manual is very good :) ). I'm using USB serial PTT control with a Baofeng - PTT is quick at TX, no problems there, but a bit

Hello Darryl, Got it. Ok. When you say "chat", what program is this? Is this something AX25 enabled that comes in HamPi?

Darrell, Since you are using the 5.10.11 kernel, stop pulseaudio to see if that frees up direwolf from being busy. sudo systemctl --system stop pulseaudio sudo systemctl --system disable pulseaudio

OK thanks for the reply, I am running Raspbian GNU/Linux 10 \n \l?with Linux 5.10.11-v7+ armv7l What I know so far, I started with HAMPI because it had other software that my club wanted. I installed

Hello Darryl, I've been doing some noodling around your "netstat -A ax25 -an" output issue and I was reminded by DL9DAU that this is a known kernel bug (I remember the issue slightly differently). The