开云体育

I installed gpsd with apt, after reading some of the output previously posted. Attempted the [ cmake -DUNITTEST=1 .. ] command again, still fails. Additional data if it helps: /path/direwolf/build#

I have followed the instructions as given, and get these errors upon attempting the dev (git checkout dev) [page 10, RPI-APRS.pdf]. {My first post, and I hope I provide what is needed to ask for help.

I am working on bringing up an APRS bot and I am having some troubles. Originally I was running Direwolf 1.6 and was having problems getting packets from the APRS-IS connection to be seen by the KISS

Thanks John. The user guide is where I ended up finding my answer.... Not sure why I didn't see it earlier before asking. Lots of sources online simply say dB as you pointed out. You are correct that

The direwolf User Guide, found here https://github.com/wb2osz/direwolf/tree/master/doc ( https://github.com/wb2osz/direwolf/tree/master/doc ) , specifies "dBi" for PHG antenna gain. The confusion

Good evening all. When setting the parameters in the direwolf.conf file for PBeacon, specifically the PHG, is the antenna gain specified in dBi or dBd? Thanks and 73 Tim KB2MFS

Thank you for pointing that out. The references have been removed from my working copy of the User Guide which will be released with version 1.8. 73, John WB2OSZ

The info about smartbeaconing on 9.11.5 - p121 http://www.hamhud.net/hh2/smartbeacon.html http://info.aprs.net/index.php?title=SmartBeaconing The first goes somewhere unrelated The second is deadlink.

Hello, I buy one and I use it with a Raspberry PI / Direwolf and an handheld (UV-K5 Quansheng). The audio output is a 4 poles audio jack (TRSS). In direwolf.conf you just have to set something like :

It would be interesting to hear what you learn from your experiment. I know that the new ardopcf modem has a built-in web ui for showing a waterfall. I wonder if we could borrow that code and add it

Hello, I use direwolf on the IC9700. Direwolf with hamlib should work well for PTT. It does for me. Although I’m using MacOS and/or Linux Debian Rasbian on a Pi. Assuming you have a Windows direwolf

Building a circuit to do PTT seems to be a time consuming and costly solution that introduces yet another point of failure. I knew that there had to a? better way. The ICOM 9700 has 2 internal USB

I was wondering if an “eye diagram” display in real-time on an oscilloscope would help in troubleshooting FSK demodulation. As I understand it, the horizontal sweep is driven by the RX baud rate

Welcome to direwolf.? There are many options for connecting a radio and computer so it can get confusing. This lead to the Radio Interface Guide (

I have an ICOM 9700 connected with a USB cable. I setup direwolf per the instructions for CM108. I tried to test my configuration with direwolf -x a and got the following message. ** Reading config

I bought it on Amazon Japan. I connected it to a USB port and it was recognised as a speaker, microphone and serial interface.? The devices that have been added to the PC are circled in green. I

Hi David, Bob, If I may chip in with my experiences gained from running a 30m BBS for a number of years. My comments are further down ...

Hello Bob, Ah... Ok, got it and yes, there seems to be some confusion here around terminology On page 61, the User Guide says: -- My original solution for this, many years ago, was to allow multiple

Hi David No possibility with an antenna change hi. What confused the issue with 9.2.2 is the table of modems says; “+” means enable multiple slicers. “-“ means single slicer. but one creates

Thanks Jeff Might also be worth experimenting with the various fldigi modes "made" for varying HF condx. I found the PSKR (ie BPSK with FEC) quite useful in that starting with the same base mode and