开云体育

I made? a second test with my FT2. The received message is clearly missing the sequence number when dispalyed in the raw screen. I'll make an issue on GitHub. This is a *serious bug* as messages

What version of GPSD are you running? GPD 3.22 has exhibited this issue in the past. -- 73, AB1PH Don Rolph

Thank you for replying David! 1. I am running version 1.7 from Git 2. Gpsd service is running yes. And cgps and gpsmon shows correct position. I have not checked it while traveling though. I will do

Hello John, A few questions here: 1. What version of Direwolf are you running? v1.6 is current and v1.7 (currently in the Github DEV branch) should be released soon. 2. Before you start direwolf, is

My TBEACON and SMARTBEACON setup only fetches new GPS position at reboot. Beacons are sent, but the GPS position do not change throughout my travel. If I reboot the RPi, it changes.? ?I am running

I am using direwolf with a RPi2 and GPIO as PTT. I was having problems with PTT getting stuck on send. Turns out it was because of a bad antenna.. A lot of RFI was created, and this caused PTT to

Hi All, As suggested I am now running dev version (1.7) of Direwolf. I was playing and testing messaging capabilities and I must say the way Direwolf handles messages and courtesy posits is excellent

Hello Geoffrey, Since you've observed that the upcoming Direwolf v1.7 has already increased the max intake byte count to 1200 bytes, it sounds like it's the right thing to do. You might consider just

The point is that the SignaLink doesn't have any capture _controls_ (i.e., volume control) in software. You have to manually turn the physical knob on the front of the box, rather than doing it in

Hi David, Thank you for your reply. I am aware of the 512 bytes limitation on the IS side, hence the filter with the wildcards. But the IS IGFILTER line is working as expected. This is pretty much the

Well it seems to be working regardless. ?\_(ツ)_/?

I picked up a SignaLink, looking at your config for direwolf, did you do anything other than change the device number? ?alsamixer doesn't show any capture devices for the SignaLink

Hello Geoffrey, Per the documentation at http://www.aprs-is.net/connecting.aspx , the maximum limit of a filtering command send to an APRS-IS Igate is 512 bytes including the CR/LF sequence. It's not

Hi All, First time posting here. I am currently in the process of migrating our club digipeaters from APRX to Direwolf. On APRX I had following setup. I would push every member of our club from IS to

Thank you for responding. I am running Raspberry Pi OS, and yes I did remove pulse. I think I read it was recommended to remove it for Direwolf. Maybe I am wrong. Thank you!

Your errors seem to be scheduler related and not Direwolf per se. Which Linux distribution is this? For an Rpi2, I would recommend to stick with Raspberry Pi OS for the best hardware compatibility. If

I am running direwolf on a RPi2 with soundcard to radio but it keep crashes and the RPi needs a reboot. I get these messages in?/var/log/messages just before the RPi freezes. Jun 26 10:33:54 direwolf

Hello Lee, I don't have a DINAH unit but I swear I've read that other Direwolf + V71A users have been able to get the RX audio levels 50. Two other ideas: 1. It seems the DINAH has an RX Boost

Thanks David, This doesn't seem to be related to the COS/VOLDN issue with the DINAH. I was already aware of that. When I connect the DINAH to a Yaesu FTM-3100R, which has a home-brew external packet

There are a lot of archived posts about this on the DINAH list and the level settings depends if you're using 1200bps, 9600pbs, which radio, etc.