|
Hope of interest. Possibly off topic.
I had to refurbish the cat house and restring the scratching posts, (tubes) as we have 5 cats?
and these cat house support posts save on the ripping up of the drapes and furniture.?
If these 10 posts were hand wound with the new 8 mm dia jute, it would be very time consuming
and difficult to apply the correct tension when winding on to the tubes,
So I started by removing the old "jute" or string leaving a plain cardboard tube.
Then I just managed to get the posts between centre's on the mini lathe picking up off the attachment nuts. I mean only JUST "phew" due to the length.
By power rotating the lathe spindle, then initially applied some wood glue all the way along the tube. It looked like a spring or spiral effect.
The start of the new jute strand was stapled, then I turned on the late, very slow RPM, and wound on the new jute, the end of the strand after winding on
the full length was stapled.
Time to complete the rewinds of jute for 10 posts, 2 hours.
Now if my wife can remember how the cat house all goes back together LOL I should be OK.
I asked her to take a photo before disassembly, she did not. GR!!!!!!!!!!!
Unbelievable but each post required 12 mm of jute, expensive repair, but it saves money on replacing the furniture and drapes.
Photo 1 Jute to be stripped off.
Photo 2 Tube between centres.
Photo 3 New jute wound on between centre's.
Photo 4 One tube done
Photo 5 Stack of 10 posts done.
Again, OT but put the lathe to some good use and could be of interest to other group cat owners.
Thanks
--
John
|
??? ??? Good work , that's part of the work smarter not harder
plan .
animal
On 2/16/24 9:50 PM, John Lindo wrote:
toggle quoted message
Show quoted text
Hope of interest. Possibly off topic.
I had to refurbish the cat house and restring the scratching
posts, (tubes) as we have 5 cats?
and these cat house support posts save on the ripping up of the
drapes and furniture.?
If these 10 posts were hand wound with the new 8 mm dia jute, it
would be very time consuming
and difficult to apply the correct tension when winding on to the
tubes,
So I started by removing the old "jute" or string leaving a plain
cardboard tube.
Then I just managed to get the posts between centre's on the mini
lathe picking up off the attachment nuts. I mean only JUST "phew"
due to the length.
By power rotating the lathe spindle, then initially applied some
wood glue all the way along the tube. It looked like a spring or
spiral effect.
The start of the new jute strand was stapled, then I turned on the
late, very slow RPM, and wound on the new jute, the end of the
strand after winding on
the full length was stapled.
Time to complete the rewinds of jute for 10 posts, 2 hours.
Now if my wife can remember how the cat house all goes back
together LOL I should be OK.
I asked her to take a photo before disassembly, she did not.
GR!!!!!!!!!!!
Unbelievable but each post required 12 mm of jute, expensive
repair, but it saves money on replacing the furniture and drapes.
Photo 1 Jute to be stripped off.
Photo 2 Tube between centres.
Photo 3 New jute wound on between centre's.
Photo 4 One tube done
Photo 5 Stack of 10 posts done.
Again, OT but put the lathe to some good use and could be of
interest to other group cat owners.
Thanks
--
John
|
Thanks Mike for your quote.
After the fact, and job done, thinking I was only half smart, Duh.
What I should have done using the 8 mm dia "jute" was to instal into the RELS system a pitch of 8 mm in the threading tables.
Machined up a split busing with a 8 mm bore, and this held in a "vee" type toolholder of a quick release tool post,
Run the "jute" through this bushing, clamped down on it so the jute had some load on it, stapled the end of the jute to the tube,
and then run the lathe as though I was screw cutting. This way would of made it totally hands free.
Oh well I did not, but my tigers will soon claw there way through this new jute, so there will be a NEXT time.?
Hope of interest
--
John
|
And you should add a spool holder for the rope so you can pay out the rope without getting extra twists in the rope or getting tangles.
And then, make an automatic glue dispenser with a roller to spread the glue.?
And then, a fan to set the glue so it is tacky for the rope to adhere to.
And then, ... oh ... I'm getting carried away...
Thanks Mike for your quote.
After the fact, and job done, thinking I was only half smart, Duh.
What I should have done using the 8 mm dia "jute" was to instal into the RELS system a pitch of 8 mm in the threading tables.
Machined up a split busing with a 8 mm bore, and this held in a "vee" type toolholder of a quick release tool post,
Run the "jute" through this bushing, clamped down on it so the jute had some load on it, stapled the end of the jute to the tube,
and then run the lathe as though I was screw cutting. This way would of made it totally hands free.
Oh well I did not, but my tigers will soon claw there way through this new jute, so there will be a NEXT time.?
Hope of interest
--
John
--
Buffalo John
|
Buffalo John
All correct, maybe next time. LOL
The lesson my wife learnt is to take a photo of anything she disassembles before she starts.
This cat house/climber has 4 levels, assembles with studded rod, c/sunk allen screws etc etc.
Amazingly we have had this cat house for over 4 years and we pass by it daily, so you would of thought?
we knew what it looked like when reassembling. Similar to driving down a road everyday, you think you know every bend
and twist until you drive it in the fog,
A few terse words were uttered after I asked her did she take the photo as NO was the reply, and then it was left to me to reassemble.
I have over the years repaired many musical instruments and by default take photos when stripping the keys off
to fit new pads and springs. All instruments are basically the same forming a common goal but each manufacturer have over the years put in there own?
ideas of how linkage, swivels, adjustments are formed into the stacks of keys.
The most complex I work on are the Soprano saxes, the smallest member of the saxophone family, and without taking photos first I would be in a world of hurt.
Also if some key, spring, pivot rods are broken upon receipt of the sax for the repairs i can show the owner is was not my doing,?
The photo attached is of a top "stack" of keys from a "Selmer" Soprano, this instrument is valued at $4500.?
I hope of interest.
--
John
|
??? When my kid first brought his sax home he was afraid that I
was gonna take it apart to see how it works he slept with it under
his bed for a while . The Sax & clarinet family have so many
neat bends & off sets & this & that who doesn't want
to see how they work ?
animal
On 2/18/24 5:52 PM, John Lindo wrote:
toggle quoted message
Show quoted text
Buffalo John
All correct, maybe next time. LOL
The lesson my wife learnt is to take a photo of anything she
disassembles before she starts.
This cat house/climber has 4 levels, assembles with studded rod,
c/sunk allen screws etc etc.
Amazingly we have had this cat house for over 4 years and we pass
by it daily, so you would of thought?
we knew what it looked like when reassembling. Similar to driving
down a road everyday, you think you know every bend
and twist until you drive it in the fog,
A few terse words were uttered after I asked her did she take the
photo as NO was the reply, and then it was left to me to
reassemble.
I have over the years repaired many musical instruments and by
default take photos when stripping the keys off
to fit new pads and springs. All instruments are basically the
same forming a common goal but each manufacturer have over the
years put in there own?
ideas of how linkage, swivels, adjustments are formed into the
stacks of keys.
The most complex I work on are the Soprano saxes, the smallest
member of the saxophone family, and without taking photos first I
would be in a world of hurt.
Also if some key, spring, pivot rods are broken upon receipt of
the sax for the repairs i can show the owner is was not my doing,?
The photo attached is of a top "stack" of keys from a "Selmer"
Soprano, this instrument is valued at $4500.?
I hope of interest.
--
John
|
I rebuilt a silver plated alto sax while in high school for a girl.? She played clarinet in our Dixieland band which was called Seven plus a Garter.? You can guess who wore the garter. I played and still have my Selmer Tenor Sax which is now over 50 years old. John ? ?
toggle quoted message
Show quoted text
From: [email protected] [mailto:[email protected]] On Behalf Of mike allen
Sent: February 18, 2024 6:25 PM
To: [email protected]
Subject: Re: [digitalhobbyist] #LATHES OT? ??? When my kid first brought his sax home he was afraid that I was gonna take it apart to see how it works he slept with it under his bed for a while . The Sax & clarinet family have so many neat bends & off sets & this & that who doesn't want to see how they work ? animal On 2/18/24 5:52 PM, John Lindo wrote: Buffalo John
All correct, maybe next time. LOL
The lesson my wife learnt is to take a photo of anything she disassembles before she starts.
This cat house/climber has 4 levels, assembles with studded rod, c/sunk allen screws etc etc.
Amazingly we have had this cat house for over 4 years and we pass by it daily, so you would of thought?
we knew what it looked like when reassembling. Similar to driving down a road everyday, you think you know every bend
and twist until you drive it in the fog,
A few terse words were uttered after I asked her did she take the photo as NO was the reply, and then it was left to me to reassemble.
I have over the years repaired many musical instruments and by default take photos when stripping the keys off
to fit new pads and springs. All instruments are basically the same forming a common goal but each manufacturer have over the years put in there own?
ideas of how linkage, swivels, adjustments are formed into the stacks of keys.
The most complex I work on are the Soprano saxes, the smallest member of the saxophone family, and without taking photos first I would be in a world of hurt.
Also if some key, spring, pivot rods are broken upon receipt of the sax for the repairs i can show the owner is was not my doing,?
The photo attached is of a top "stack" of keys from a "Selmer" Soprano, this instrument is valued at $4500.?
I hope of interest.
--
John
|
There's only 2 semi substantial things that I have taken apart in
my days . A automatic transmission in Hi school & a real
Cuckoo clock from Germany when I was @ 10-11 . I still have most
of the clock in a couple of boxes , it's on one of my bucket
list's . I always wondered if a sax or clarinet would end up on
that list . I enjoy watching Wes Lee Music Repair on youtube . He
does a lot of explaining . I watch basketball & the Alaska
shows on TV, that pretty much it for TV . I kinda count on youtube
for the rest .
animal
On 2/18/24 6:53 PM, John Dammeyer
wrote:
toggle quoted message
Show quoted text
I
rebuilt a silver plated alto sax while in high school for a
girl.? She played clarinet in our Dixieland band which was
called Seven plus a Garter.? You can guess who wore the
garter.
I
played and still have my Selmer Tenor Sax which is now over
50 years old.
John
?
?
?
??? When my kid first brought his sax home he was afraid that
I was gonna take it apart to see how it works he slept with it
under his bed for a while . The Sax & clarinet family have
so many neat bends & off sets & this & that who
doesn't want to see how they work ?
animal
On 2/18/24 5:52 PM, John Lindo wrote:
Buffalo John
All correct, maybe next time. LOL
The lesson my wife learnt is to take a photo of anything she
disassembles before she starts.
This cat house/climber has 4 levels, assembles with studded
rod, c/sunk allen screws etc etc.
Amazingly we have had this cat house for over 4 years and we
pass by it daily, so you would of thought?
we knew what it looked like when reassembling. Similar to
driving down a road everyday, you think you know every bend
and twist until you drive it in the fog,
A few terse words were uttered after I asked her did she
take the photo as NO was the reply, and then it was left to
me to reassemble.
I have over the years repaired many musical instruments and
by default take photos when stripping the keys off
to fit new pads and springs. All instruments are basically
the same forming a common goal but each manufacturer have
over the years put in there own?
ideas of how linkage, swivels, adjustments are formed into
the stacks of keys.
The most complex I work on are the Soprano saxes, the
smallest member of the saxophone family, and without taking
photos first I would be in a world of hurt.
Also if some key, spring, pivot rods are broken upon receipt
of the sax for the repairs i can show the owner is was not
my doing,?
The photo attached is of a top "stack" of keys from a
"Selmer" Soprano, this instrument is valued at $4500.?
I hope of interest.
--
John
|
ya need one of these
animal
On 2/18/24 6:53 PM, John Dammeyer
wrote:
toggle quoted message
Show quoted text
I
rebuilt a silver plated alto sax while in high school for a
girl.? She played clarinet in our Dixieland band which was
called Seven plus a Garter.? You can guess who wore the
garter.
I
played and still have my Selmer Tenor Sax which is now over
50 years old.
John
?
?
?
??? When my kid first brought his sax home he was afraid that
I was gonna take it apart to see how it works he slept with it
under his bed for a while . The Sax & clarinet family have
so many neat bends & off sets & this & that who
doesn't want to see how they work ?
animal
On 2/18/24 5:52 PM, John Lindo wrote:
Buffalo John
All correct, maybe next time. LOL
The lesson my wife learnt is to take a photo of anything she
disassembles before she starts.
This cat house/climber has 4 levels, assembles with studded
rod, c/sunk allen screws etc etc.
Amazingly we have had this cat house for over 4 years and we
pass by it daily, so you would of thought?
we knew what it looked like when reassembling. Similar to
driving down a road everyday, you think you know every bend
and twist until you drive it in the fog,
A few terse words were uttered after I asked her did she
take the photo as NO was the reply, and then it was left to
me to reassemble.
I have over the years repaired many musical instruments and
by default take photos when stripping the keys off
to fit new pads and springs. All instruments are basically
the same forming a common goal but each manufacturer have
over the years put in there own?
ideas of how linkage, swivels, adjustments are formed into
the stacks of keys.
The most complex I work on are the Soprano saxes, the
smallest member of the saxophone family, and without taking
photos first I would be in a world of hurt.
Also if some key, spring, pivot rods are broken upon receipt
of the sax for the repairs i can show the owner is was not
my doing,?
The photo attached is of a top "stack" of keys from a
"Selmer" Soprano, this instrument is valued at $4500.?
I hope of interest.
--
John
|
I love the workshop, twice the space, and played a contra bass in a jazz band many years ago in Santa Barbara. It needed to be supported by a jack screw off the floor and played sitting down, as it was too heavy to hang around?the neck. All have a good week. Cheers
On Mon, 19 Feb 2024 at 06:20, mike allen < animal@...> wrote:
ya need one of these
animal
On 2/18/24 6:53 PM, John Dammeyer
wrote:
I
rebuilt a silver plated alto sax while in high school for a
girl.? She played clarinet in our Dixieland band which was
called Seven plus a Garter.? You can guess who wore the
garter.
I
played and still have my Selmer Tenor Sax which is now over
50 years old.
John
?
?
?
??? When my kid first brought his sax home he was afraid that
I was gonna take it apart to see how it works he slept with it
under his bed for a while . The Sax & clarinet family have
so many neat bends & off sets & this & that who
doesn't want to see how they work ?
animal
On 2/18/24 5:52 PM, John Lindo wrote:
Buffalo John
All correct, maybe next time. LOL
The lesson my wife learnt is to take a photo of anything she
disassembles before she starts.
This cat house/climber has 4 levels, assembles with studded
rod, c/sunk allen screws etc etc.
Amazingly we have had this cat house for over 4 years and we
pass by it daily, so you would of thought?
we knew what it looked like when reassembling. Similar to
driving down a road everyday, you think you know every bend
and twist until you drive it in the fog,
A few terse words were uttered after I asked her did she
take the photo as NO was the reply, and then it was left to
me to reassemble.
I have over the years repaired many musical instruments and
by default take photos when stripping the keys off
to fit new pads and springs. All instruments are basically
the same forming a common goal but each manufacturer have
over the years put in there own?
ideas of how linkage, swivels, adjustments are formed into
the stacks of keys.
The most complex I work on are the Soprano saxes, the
smallest member of the saxophone family, and without taking
photos first I would be in a world of hurt.
Also if some key, spring, pivot rods are broken upon receipt
of the sax for the repairs i can show the owner is was not
my doing,?
The photo attached is of a top "stack" of keys from a
"Selmer" Soprano, this instrument is valued at $4500.?
I hope of interest.
--
John
--
John
|
Hi John. Nice to hear from you, hope you are keeping well and busy. Selmer Mk 5 which I am guessing you have from the age, please keep well secure as these saxes are priceless. As a tip photograph?totally including the serial number engraved normally at the base. Ensure you have it well covered in your home insurance policy. You never know . Cheers John
On Mon, 19 Feb 2024 at 03:53, John Dammeyer < johnd@...> wrote: I rebuilt a silver plated alto sax while in high school for a girl.? She played clarinet in our Dixieland band which was called Seven plus a Garter.? You can guess who wore the garter. I played and still have my Selmer Tenor Sax which is now over 50 years old. John ? ? ? ??? When my kid first brought his sax home he was afraid that I was gonna take it apart to see how it works he slept with it under his bed for a while . The Sax & clarinet family have so many neat bends & off sets & this & that who doesn't want to see how they work ? animal On 2/18/24 5:52 PM, John Lindo wrote: Buffalo John
All correct, maybe next time. LOL
The lesson my wife learnt is to take a photo of anything she disassembles before she starts.
This cat house/climber has 4 levels, assembles with studded rod, c/sunk allen screws etc etc.
Amazingly we have had this cat house for over 4 years and we pass by it daily, so you would of thought?
we knew what it looked like when reassembling. Similar to driving down a road everyday, you think you know every bend
and twist until you drive it in the fog,
A few terse words were uttered after I asked her did she take the photo as NO was the reply, and then it was left to me to reassemble.
I have over the years repaired many musical instruments and by default take photos when stripping the keys off
to fit new pads and springs. All instruments are basically the same forming a common goal but each manufacturer have over the years put in there own?
ideas of how linkage, swivels, adjustments are formed into the stacks of keys.
The most complex I work on are the Soprano saxes, the smallest member of the saxophone family, and without taking photos first I would be in a world of hurt.
Also if some key, spring, pivot rods are broken upon receipt of the sax for the repairs i can show the owner is was not my doing,?
The photo attached is of a top "stack" of keys from a "Selmer" Soprano, this instrument is valued at $4500.?
I hope of interest.
--
John
--
John
|
Hi John, Emotionally not so well due to some family issues but nothing prevents me from pulling out the camera to take some shots. ? It’s a Mark VI, not a V. 
? And yes the serial number matches the certificate. 
? ?
toggle quoted message
Show quoted text
From: [email protected] [mailto:[email protected]] On Behalf Of John Lindo
Sent: February 18, 2024 9:33 PM
To: [email protected]
Subject: Re: [digitalhobbyist] #LATHES OT? Nice to hear from you, hope you are keeping well and busy. Selmer Mk 5 which I am guessing you have from the age, please keep well secure as these saxes are priceless. As a tip photograph?totally including the serial number engraved normally at the base. Ensure you have it well covered in your home insurance policy. ? On Mon, 19 Feb 2024 at 03:53, John Dammeyer <johnd@...> wrote: I rebuilt a silver plated alto sax while in high school for a girl.? She played clarinet in our Dixieland band which was called Seven plus a Garter.? You can guess who wore the garter. I played and still have my Selmer Tenor Sax which is now over 50 years old. John ? ? ? ??? When my kid first brought his sax home he was afraid that I was gonna take it apart to see how it works he slept with it under his bed for a while . The Sax & clarinet family have so many neat bends & off sets & this & that who doesn't want to see how they work ? animal On 2/18/24 5:52 PM, John Lindo wrote: Buffalo John
All correct, maybe next time. LOL
The lesson my wife learnt is to take a photo of anything she disassembles before she starts.
This cat house/climber has 4 levels, assembles with studded rod, c/sunk allen screws etc etc.
Amazingly we have had this cat house for over 4 years and we pass by it daily, so you would of thought?
we knew what it looked like when reassembling. Similar to driving down a road everyday, you think you know every bend
and twist until you drive it in the fog,
A few terse words were uttered after I asked her did she take the photo as NO was the reply, and then it was left to me to reassemble.
I have over the years repaired many musical instruments and by default take photos when stripping the keys off
to fit new pads and springs. All instruments are basically the same forming a common goal but each manufacturer have over the years put in there own?
ideas of how linkage, swivels, adjustments are formed into the stacks of keys.
The most complex I work on are the Soprano saxes, the smallest member of the saxophone family, and without taking photos first I would be in a world of hurt.
Also if some key, spring, pivot rods are broken upon receipt of the sax for the repairs i can show the owner is was not my doing,?
The photo attached is of a top "stack" of keys from a "Selmer" Soprano, this instrument is valued at $4500.?
I hope of interest.
--
John
--
John
|
Sorry to read of your troubles, but as we say, tomar los días "poco poco". Roughly translates to "Take the days of life in small amounts".? As we get older we begin to slowly realize "the cemetery?is full of indispensable?people". Take care. My typo error, MK IV , what a real beauty, and with great care it will see us out and 5 generations plus more. Please get it insured if not already, it won't bring it back if lost or stolen, or fire damage etc but could help financially take out the sting a bit. I am envious you have such an instrument, I would play it every hour of the day, the great Paul Desmond? used this MK IV most of his playing career, I often wonder where all the instruments?are now from famous? artists, well we all know where most of the great legends of jazz are now. Stay positive
On Mon, 19 Feb 2024 at 07:46, John Dammeyer < johnd@...> wrote: Hi John, Emotionally not so well due to some family issues but nothing prevents me from pulling out the camera to take some shots. ? It’s a Mark VI, not a V. 
? And yes the serial number matches the certificate. 
? ? ? Nice to hear from you, hope you are keeping well and busy. Selmer Mk 5 which I am guessing you have from the age, please keep well secure as these saxes are priceless. As a tip photograph?totally including the serial number engraved normally at the base. Ensure you have it well covered in your home insurance policy. ? On Mon, 19 Feb 2024 at 03:53, John Dammeyer <johnd@...> wrote: I rebuilt a silver plated alto sax while in high school for a girl.? She played clarinet in our Dixieland band which was called Seven plus a Garter.? You can guess who wore the garter. I played and still have my Selmer Tenor Sax which is now over 50 years old. John ? ? ? ??? When my kid first brought his sax home he was afraid that I was gonna take it apart to see how it works he slept with it under his bed for a while . The Sax & clarinet family have so many neat bends & off sets & this & that who doesn't want to see how they work ? animal On 2/18/24 5:52 PM, John Lindo wrote: Buffalo John
All correct, maybe next time. LOL
The lesson my wife learnt is to take a photo of anything she disassembles before she starts.
This cat house/climber has 4 levels, assembles with studded rod, c/sunk allen screws etc etc.
Amazingly we have had this cat house for over 4 years and we pass by it daily, so you would of thought?
we knew what it looked like when reassembling. Similar to driving down a road everyday, you think you know every bend
and twist until you drive it in the fog,
A few terse words were uttered after I asked her did she take the photo as NO was the reply, and then it was left to me to reassemble.
I have over the years repaired many musical instruments and by default take photos when stripping the keys off
to fit new pads and springs. All instruments are basically the same forming a common goal but each manufacturer have over the years put in there own?
ideas of how linkage, swivels, adjustments are formed into the stacks of keys.
The most complex I work on are the Soprano saxes, the smallest member of the saxophone family, and without taking photos first I would be in a world of hurt.
Also if some key, spring, pivot rods are broken upon receipt of the sax for the repairs i can show the owner is was not my doing,?
The photo attached is of a top "stack" of keys from a "Selmer" Soprano, this instrument is valued at $4500.?
I hope of interest.
--
John
--
John
--
John
|
John Lindo
BuffaloJohn
