开云体育

Today I open the page of the D3pro software, and I see this tag: Effective March 31, 2025, Crestron D3 Pro software will be transitioned into maintenance mode. For more information, refer to community.crestron.com/s/article/3094. Seems D3pro will be obsolete soon. I didn't thought this will happen, at least for a few years more. In fact the article was lounched since Jan 29 2025.

Anyone have a IR driver for a Polycom HDX 9k series codec they'd be willing to share? TIA, Steve

Does anyone having Simpl windows module for Poly G62

Hello group! I have been tasked with specifying a security system from the Works With Crestron Home list. Does anybody have any personal reccomendations or caveats concerning any particular systems? Would like to use Honeywell or DSC because of availability through our partner, but can go another route if anything integrates particularly well. Thanks!

Hi All, Trying to configure RFID for dimmers from network device tree view. Only device showing up is the processor, the touchpanels, gwexer, not showing up. They show in device discovery just not in network device tree. Any help is appreciated. Thank you.

I have hours and hours in to SIMPL with a new Sony STR-AZ7000ES. Did the whole CCD thing, with True Blue, etc. Could not get it to work. Tried STR-ZAxx 1.1 (with Newtonsoft.Json errors, whatever that means). Am I really resorting to IR for this thing?! Is it Crestron or Sony?! Our RTI programmer had zero issues with same unit...2 minutes to get it going. SMH

Hi All, I have a site with some CHV stats, most with RTS/RTHS remote sensors. We think that we have seen issues with display offsets. We had set offsets ~ 1-2 year ago to compensate for variances. The MBath unit had a 6 degree offset. unfortunately, the client went thru the winter with uncomfortable environment, and now we find that we need to eliminate the 6 degree offset to make thing right. We're sure that our setting were correct when we did the offsets. Have any others seen the remote sensors need offsets and then have the system need to revert back to no offset? TIA!

So I have a cp3 controlling a group of nvx boxes, to isolate some issues i was having with flickering i moved all the nvx to their own vlan and subnet(that's still not fixed but I'll address that in another thread some day) I have the switch doing l3 routing, so no firewall or acls in between blocking traffic, and all devices can ping each other d30 to cp3 and vice versa, all good there, same issue on d30 and a lot of 350s the ip-id won't go online, it worked perfectly fine when in the same subnet cp3@ 10.0.10.x(/24) nvx@ 10.0.19.x(/24) My question is, is there a setting I have to set on the processor to let routed devices connect? This almost seems like it has to be something config wise since they can ping each other

Is there any way inside a SIMPL module to know if any of it's input signals are connected in the root program? For example I have a module with 10 input signals and 10 output feedback signals. I want all of the feedback signals to go high at the same time but only for the signals that have connected inputs. Is this possible?

Hi guys, I need some old takers wisdom on this. setup: Bpt door bell connects to crestron via sip (I think) and the audio and video gets distributed to crestron touch panel 6PL via C2N-IADS30X24 and C2N-IVDS24X24. At the moment, there’s no audible ring out from the crestron panels only the Bpt panel rings out. But on the crestron panels, the intercom subpage comes up and you can answer the call and open the gate etc. How do I set the audible ring out to ring when someone presses the door bell? Any help is appreciated.

Has anyone had any luck with these TVs and getting discrete control? I have the ability to use HDMI-CEC, LAN, or IR control, but need to know if there is a solution I should pursue which others have found to be reliable. I have tried HDMI CEC standard on off commands of \xE0\x04 and \xE0\x36 without any luck. I am getting a constant response of \x04\x83 from the TV itself, so it does look like it is there, just don't know what it will respond to. Any help is appreciated. Thanks!

Hate to beat a dead horse here…I know that these have been discussed ad nausea. Has anyone had any experience with the 32” model Samsung Frame TV? I’ve had pretty good results with all of the other models via Ex-link but for some reason the 32” model cannot be turned on. All the other commands in use on other Frame models work fine except for the power on command. I thought I had it solved as it responded to WOL but after a short while that also stops working. The IP module also gives the same results…works fine then will no longer power on. Something is going to sleep and it seems to be specific to the 32” model. Also, on a slightly different note, the Samsung IP 1.3 from the store has that Newtonsoft requirement that was a “thing” recently…any fix for that?

Hello, Here's my issue: I have an old ViewSonic PRO-8100 connected via RS-232 (port 2) which controlled the power off & on, showed me the lamp hours on my touch panels (Projector on...Lamp hours: 105) through a user module when the MC3 was connected (which I still have). Now I have a CP3 installed and the message on the touch panel says Projector on...Lamp Hours: 0 but the power off & on still functions (still RS-232 port 2), so the CP3 isn't seeing the lamp hours information. Is there a difference in the way that the serial ports receive data between the MC3 and the CP3? Donald

I know these are not the most respected pieces of hardware. I picked one up from surplus and finally got around to playing with it. I can access it through toolbox but I don't have the username and password. It has the 2.0 firmware. The default admin/admin does not work. A hard reset only resets the DHCP. I have been checking around and there doesn't seem to be a way to do a hard reset. The other NVX units have at least a process albeit long one to do a hard reset (11 times pressing reset). Someone on Reddit says there is a way to through a USB drive. I don't have access to that program. Any thoughts? I know there will be a lot of folks that say it is not worth the trouble.

Programmer: Pulse Group I found a "Pulse Group" in Vegas who may have done it...waiting to hear from them. Based on what I can tell, this was probably a template used on a ton of jobs. Slot1: SourceFile : W:\Egnyte\Shared\Source Code\NTA_Main\NTA_SUB\FF-NY\Program\v2.0\NTA-FFNY-PP-v2.0 ProgramFile : NTA-FFNY-PP-v2.0.smw SystemName : Lot8 Programmer : Pulse Group CompiledOn : 8/13/2019 4:45 PM Slot2: SourceFile : W:\Egnyte\Shared\Source Code\NTA_Main\NTA_SUB\FF-NY\Program\NTA-FF-NY-SLOT2-ATV_V1 ProgramFile : NTA-FF-NY-SLOT2-ATV_V1.smw SystemName : LOT8 ATV Programmer : Pulse Group CompiledOn : 11/7/2017 8:16 AM

Hi All Is there a way to REMOTELY (VPN) change which SSID a TSR is connected to? I've looked in Console help, the ToolBox function list and the web page. Could it actually be that Crestron expects me to drive 3.5 hours one-way to change the SSID on a remote??? (Probably...:( ) TIA

Hi all, i'm looking for a module to control ADA Suite 8x8, but I believe the Suite 16 module will work. We were a ADA dealer, but unfortunately they are no longer in business. Any help would b greatly appreciated.

Recently my Sonos port and connect required a reset to factory settings. While the Sonos connect no longer displayed on our touch panels, the Sonos port would. We kept the Sonos connect because we rarely listen to two different stations in our home and we already owned it, so we use the Port as our main player and the connect as a back up. after resetting the units to factory default, Crestron Home cannot connect to them. It seems them on the network but gives me an error in diagnostics that the “desired household is not found”. I see the household name on the diagnostic screen in the Cresteon home App. However I do not know how to reset the name either on the Sonos or the Home app so they match I deleted the connect from my devices thinking I could just rescan and add it back, but the Home App will not allow me to add the connect. I have been reluctant to remove the SonosPort because even though I can’t see it on the touch panel and the panel states it’s “offline” I am able to listen to my sonos in my house because I just control the Sonos with the Sonos app on my phone I’ve read the Cresteon Sonos troubleshooting guide which actually has this exact error in the document, but I am unable to reconnect the Sonos regardless any insight would be greatly appreciated. ty james

Hello, I'd like to build a project to run on Crestron Go for Ipad to control Crestron Procise PSPHD. Does anyone here have a Crestron Procise PSPHD and Crestron Go on an Ipad to control? I've recently installed a Crestron Procise PSPHD in my home theatre. I have Toolbox, Simpl Windows, VT-Pro but not Smart Graphics or Flash. I have A RMC3 controller I can see the devices in Toolbox I've been advised there may be a template for the Procise PSPHD for VT-Pro to use for Crestron App and X-Panel. Does anyone know if this is true? With thanks

Hello all, I have been using a Send mail V02 module on port 2525. But I am being told that port2525 is a security risk and the network guys we work with started blocking both 25 and 2525 so I need an alternate way to send emails to our team for things like high Temperatures. What are you guys using that is secure to send emails from a CP4/PRO4 ? Thank you, Jon