Recently my Sonos port and connect required a reset to factory settings. ?While the Sonos connect no longer displayed on our touch panels, the Sonos port would. ?We kept the Sonos connect because we rarely listen to two different stations in our home and we already owned it, so we use the Port as our main player and the connect as a back up.?

after resetting the units to factory default, Crestron Home cannot connect to them. It seems them on the network but gives me an error in diagnostics that the “desired household is not found”. I see the household name on the diagnostic screen in the Cresteon home App. However I do not know how to reset the name either on the Sonos or the Home app so they match?

?

I deleted the connect from my devices thinking I could just rescan and add it back, but the Home App will not allow me to add the connect. I have been reluctant to remove the SonosPort because even though I can’t see it on the touch panel and the panel states it’s “offline” I am able to listen to my

sonos in my house because I just control the Sonos with the Sonos app on my phone?

?

I’ve read the Cresteon Sonos troubleshooting guide which actually has this exact error in the document, but I am unable to reconnect the Sonos regardless?

?

any insight would be greatly appreciated.?

ty

?

james

?

Hello, I'd like to build a project to run on Crestron Go for Ipad to control Crestron Procise PSPHD.??

?

Does anyone here have a Crestron Procise PSPHD and Crestron Go on an Ipad to control?

?

I've recently installed a Crestron Procise PSPHD in my home theatre. I have Toolbox, Simpl Windows, VT-Pro but not Smart Graphics or Flash. I have A RMC3 controller I can see the devices in Toolbox

?

I've been advised there may be a template for the Procise PSPHD for VT-Pro to use for Crestron App and X-Panel.? Does anyone know if this is true?

?

With thanks

Or you can use a triggerable audio player(WAV, MP3) and page it through the speakers...

?

?

Ring where? At the 6L touchpanels?

?

Load a sound in them and trigger the join # with an oscillator. No?

Bpt door bell connects to crestron via sip (I think) and the audio and video gets distributed to crestron touch panel 6PL via C2N-IADS30X24 and C2N-IVDS24X24.

?

At the moment, there’s no audible ring out from the crestron panels only the Bpt panel rings out. But on the crestron panels, the intercom subpage comes up and you can answer the call and open the gate etc. How do I set the audible ring out to ring when someone presses the door bell?

?

Any help is appreciated.

We are using SMTP2Go and I just tested with port 587 and that works. so we are going to change to that port and IT guys are happy with that

?

Thank you

Not sure if it matters what the destination is, but I have used SMTP2GO as an intermidiary forwarding service for years with success. It does use 2525 though.

?

It at least stops my processor source IP from being flagged...

Hello all,

I have been using a Send mail V02 module on port 2525. But I am being told that port2525 is a security risk and the network guys we work with started blocking both 25 and 2525 so I need an alternate way to send emails to our team for things like high Temperatures.

?

What are you guys using that is secure to send emails from a CP4/PRO4 ?

?

Thank you,

?

Jon

?

FYI, since v2.001.0174 FW, Crestron is recommending using the 5 gHz band only.

This is in addition to their best practice of not allowing 'roaming', but locking each remote to a dedicated SSID on the closest AP...

I'm just impressed that the stuff still works!!...:)

Thank you for posting this. I wanted to change 310 Wifi band from auto to 2.4 and did the help all and nothing about wifi in help all list. I found your post about wifisetup and tried wifiband and that works. it report back Auto, but sending WIFIBAND 2.4 (doesn't need to be all caps), the remote seemed to disconnect for a few seconds and then reconnect. I sent WIFIBAND again and it came back with wifi band is 2.4

?

Just posting this in case it helps anyone else, Cheers.

Hi Andrew. I think I also have a module, so if all else fails let me know and I will try and dig it out for you.?

Search in the files section, there's something there.

If that doesn't work I have one I can share with you, think it came from the Yahoo group (yes it's that old...)

Hi all, i'm looking for a module to control ADA Suite 8x8, but I believe the Suite 16 module will work.?

We were a ADA dealer, but unfortunately they are no longer in business.

Any help would b greatly appreciated.

If you are going to just use the paging/chime function of NAX/Home, I would think all you would need would be a contact closure input to the processor. That could be a simple push-button of your choosing in any housing you like. No?

My stb's have been upgraded probably 4 times since I signed on with Verizon.? I used the original remote to collect the IR codes and everything has worked fine through all the upgrades until the 4100's.? While in the guide, every third or so press to scroll down or up, it does a double press.? That's the only problem.

Agreed. I've also had good luck with control. the files section has this IR Driver that I've been using:

?

I have had some issues with the IPC4100's needing reboots occasionally. Probably when they don't like an overnight update.

It's rare but noticeable...

The mic will tell you when the different lobes gate on/off.

?

MXA910 Response:

< REP x AUTOMIX_GATE_OUT_EXT_SIG ON >

< REP x AUTOMIX_GATE_OUT_EXT_SIG OFF >

?

Where x is the corresponding lobe.

?

?

You will have to turn off the "Automatic Coverage" in the MXA920 for this to work.

Yes but the thing is that if you place the simpl+ module inside the Simpl module, the signals will always be defined (from argument definition), right??