¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. Crestron
  2. Messages
Expanded Topics Messages Polls
Date
Running SIMPL debugger continuously

 

I'm?not a full-time Crestron programmer; more of sysadmin, trying to build more robust observability into all of our room designs.? The signals in SIMPL debugger are quite valuable information, and I'd like to log certain signals continuously at all times, ideally sending to an external syslog server.? Is that possible?? The debugger seems to disconnect after a few minutes of inactivity.? I do have syslog enabled, but it doesn't seem to include this debug information.
Route NAX AES67 audio to NVX analog output

 

I'm trying to route audio from sources connected to a DM-NAX-8ZSA, to the analog audio output on a DM-NVX-360.? I've gotten it to work through the NVX's HDMI output, but nothing from the audio output.

I did it successfully several years ago, with older NVX firmware.? I'm passing the NAX source's Port, Multicast Address, and Session Name to the corresponding signals on the NVX's AES67 RX slot.? Changing the AudioSource signal from 0d (Auto) to 5d (AES67) does send the audio to the HDMI output, but there's no change (no audio) on the analog phoenix connector.

Anyone know what I'm missing?

Thanks in advance!
Need an IR code for Cignal TV SetupBox

 

Is there someone have experience to control a Cignal Setupbox. I don't have an IR learner and I am just wondering if someone have an IR file for the said setupbox Please find the below link for references.
Re: Trying to Understand Crestron Gateways. Helped Needed please!!!

 

¿ªÔÆÌåÓý

Only thing to keep in mind.? If you want to load the MX850, you will need to first connect to the ML-600 via Toolbox then once it is recognized, you would disconnect it and connect the 850MX and hit upload.? That is the only way that we have ever gotten to uploads to work.

?

Pat M

?

?

From: "[email protected]" <[email protected]> on behalf of "lokikallas via groups.io" <lokikallas@...>
Reply-To: "[email protected]" <[email protected]>
Date: Wednesday, May 29, 2024 at 9:57?AM
To: "[email protected]" <[email protected]>
Subject: Re: [crestron] Trying to Understand Crestron Gateways. Helped Needed please!!!

?

The URC850's and the ML600's are functionally identical.? And you can load the VTP file directly as if it were an ML600 IME.

Re: Trying to Understand Crestron Gateways. Helped Needed please!!!

 

The URC850's and the ML600's are functionally identical.? And you can load the VTP file directly as if it were an ML600 IME.
Re: Trying to Understand Crestron Gateways. Helped Needed please!!!

 

Thanks for the feedback on remotes, I will stick with the ML 600's and down the road maybe go with the TSR 310's in the future once the ML stop working. Just curious our the MX850's an upgrade to ML600's.? And if so you said they will accept the ML600 files directly with no extra programming?

Cheers

Oil Country
Re: Rachio crestron market with version 3

 

Thanks a lot Jay for the feedback ?

Yes the irrigation delay will be used with the smart local weather station from Rachio.
Good to know that Rachio model 2 work fine with the crestron market module on your side.

=> Is there anyone using the Rachio model 3 somewhere with this crestron market module to confirme it please ?
Re: Trying to Understand Crestron Gateways. Helped Needed please!!!

 

The MLX2's were some of the worst remotes crestron ever sold.? ?Buy some Mx850's and load the ml600 files to them and call it a day.
Re: Rachio crestron market with version 3

 

¿ªÔÆÌåÓý

Though I haven't tested it, to the best of my knowledge, Rachio hasn't made changes to their API so the Crestron module should work fine with the Rachio 3.? I have a Rachio 2 with 9 zones and don't have any issues.? That being said, I personally only use the module in a very limited way as the Rachio app provides a very good UI for controlling all aspects of their irrigation controller.? The only thing I use the Crestron module for is to delay irrigation if my Tempest weather station reports that there has been significant rain.?

There is a full integration between the Tempest and Rachio available but there is a charge for it.? Since I live in an area defined as "high desert" it doesn't offer any real savings in water usage for me.

Hope this helps

Jay

On 5/28/2024 11:25 AM, JiiB's via groups.io wrote:

Hello guys,

just want to know if someone have feedback on the crestron market Rachio irrigation module recently ?

I just want to know if it¡¯s still working with the last Rachio 3 unit ?

i am looking to install it with 16 zones

thanks all
Rachio crestron market with version 3

 

Hello guys,

just want to know if someone have feedback on the crestron market Rachio irrigation module recently ?

I just want to know if it¡¯s still working with the last Rachio 3 unit ?

i am looking to install it with 16 zones

thanks all
Re: DMPS3-4K-350-C and the "Content LAN" Connection for AirMedia

 

FTR, the 350 still shows as current with no caveats on the product page:
Re: DMPS3-4K-350-C and the "Content LAN" Connection for AirMedia

 

While it's not currently listed as such, within the last 30 days, I could SWEAR that the DMPS3-4K-350-C was listed as discontinued on Crestron's website or portal (can't remember which I was on)(yes the 3-Series 4K version). I could certainly be wrong, but I do seem to remember asking a coworker if he had seen any formal explicit correspondence about it (such as an e-mail blast), to which he hadn't.

I'd be a little nervous specifying a current DMPS into new projects, especially if a major change is coming to the DMPS line up, say, in the coming weeks, though this is nothing more than rumblings and speculation.

The vibe I get from Crestron is they want to sell the poorly designed and overpriced HD-PS stuff as a replacement to a DMPS. Much preferred the older "receiving" form factor over the current "transmitting" form factor, though if many of your inputs are at the table, it'll probably fit into the workflow just fine.
Re: DMPS3-4K-350-C and the "Content LAN" Connection for AirMedia

 

¿ªÔÆÌåÓý

On our installs we don¡¯t use AirMedias on the AV Lan it is on the customers enterprise network. We have canvas enabled and set the auto switching on which is also the default.?
True on lack of 4k on the HDMI input. Still
Imo it¡¯s better to sell a AM 3000 than the software version.?


On May 25, 2024, at 12:53?PM, ckangis via groups.io <chris@...> wrote:

?Thanks Kevin,
That makes sense. The only think that I see as a downside with the 3200 is that the HDMI input is only v1.4 and can only do 1080p-ish video...

Also, in looking at SMW integration, I see this note about the 'VideoOut' analog input of the Display Switching Slot for switching between the HDMI IN input and AirMedia function:

This join should not be exerted if <AirMediaCanvasEnable> is set to High/1.

If Canvas is needed, can you enable the Canvas and set the VideoOut to '0' and then when Canvas is not used, go back to using a '1' or '2' for the VideoOut normal switching??
Or do you need to Not attach a signal to VideoOut if you even want to use the Canvas feature??

TIA!

Re: Smart graphics button state (active vs inactive)

 

On Mon, May 27, 2024 at 10:39 AM, Olivier Royer wrote:
May I suggest using optocouplers (or optoisolators...
That's a really good suggestion!!
Re: Smart graphics button state (active vs inactive)

 
Edited

The "Advanced Button" is the goto button for this project.
About "tapping the 12VDC" to a versiport. May I suggest using optocouplers (or optoisolators depending in what part of the world you're in) to couple (or isolate) the generac from the versiports.
The Crestron versiports have a common ground and the 7 LEDs of the generac might not, and even if they have I would not trust connecting them directly. Building a board with 7 optocouplers is not so complicated and can save you a lot of misery.

----edit---

Oh man, you don't even have to build it!
https://www.amazon.ca/Channel-Optocoupler-Isolation-Converter-Isolator/dp/B09S3XTM5P/ref=asc_df_B09S3XTM5P/?tag=googleshopc0c-20&linkCode=df0&hvadid=683150834842&hvpos=&hvnetw=g&hvrand=2513852794165375712&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9000411&hvtargid=pla-1869623874401&psc=1&mcid=b4aea703722032ed9634788023f5a0cf&gad_source=1
Re: Smart graphics button state (active vs inactive)

 

Going to have to be very careful with tapping that control board.? It is still available but wicked expensive.
Re: Smart graphics button state (active vs inactive)

 

Nice!! keep us posted...
Re: QSC volume control

 

Thanks.? I see All, External, None, and script as options.
It is set to all and I can mute that gain block, just can't control the level.
Re: Smart graphics button state (active vs inactive)

 

Thank you.? I'll get back to this later.? Somehow the Queen has found something more important for me to do on my day off.
This is kind of a fun project but it would be nice to know that the generator is doing what it's supposed to when I'm not home.
This generator is one series to old for factory wifi but when there's the will, there is always the way.?
Re: QSC volume control

 

In design mode (not connected to the core or in emulation) select the gain block and it¡¯s on the properties window on the upper right corner, all the way at the button of that section if I remember.?
3141 - 3160 of 256448