¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
Date

Android Streaming Box IP Control Crestron #crestron

 

Is there any android streaming box which can controlled by ip?
Requirement: App launching and text input.
TIA?


"The context MasterIPTable is not known for this device"

 

I unfortunately seem to have deleted the MasterIPTable and now my program is acting up. What can I do?

Here is the entire error message after compiling and before uploading. The processor is a DMPS3-4K-150-C. Any assistance is appreciated.

Failure: Could not determine the IP Table contents IP Table content is necessary for determining the current operation mode.

Failure: Could not determine the IP Table contents IP Table content is necessary for determining the current operation mode.
The ability requested (code = 136193) is not supported on MasterIPTable (context = MasterIPTable).
The context MasterIPTable is not known for this device.


2 files uploaded #file-notice

Group Notification
 

The following files and folders have been uploaded to the Files area of the [email protected] group.

By: ckangis <chris@...>

Description:
Sony XBR Volume module for RS232


Re: Sony Professional Display problems.

 

On Thu, Sep 1, 2022 at 04:27 PM, MSTC wrote:
Since there was so little time to get this working today, had to revert to 232. Of course, power control is good but the the vol and mute do not work. UGH !!?
I actually prefer RS232. at least in Resi with the 'Smart TV' crap not having IP connections elminates alot of spurious issues, even with ProMode turning everything off...
I'll post an XBR volume module that *May* work for you for volume control - converts 0-100% to serial strings...


Re: Sony Professional Display problems.

 

Also try doing a factory reset on the TV.? I have had a few cases where all the settings were right but IP control did not work until I did a factory reset.


Re: Sony Professional Display problems.

 

¿ªÔÆÌåÓý

Check with Sony to ensure menu items are correctly set . .? .

?

?

866-924-7669

?

?

Installsupport ??@????? am??????? .sony????? .com

?

From: <[email protected]> on behalf of Tray Schaeffer <trayschaeffer@...>
Reply-To: <[email protected]>
Date: Thursday, September 1, 2022 at 11:54 AM
To: <[email protected]>
Subject: Re: [crestron] Sony Professional Display problems.

?

Cannot get IP control to work at all for FWD-65X81CH.?

Used the Bravia 2014 module and also tried the Crestron CCD driver.?
Would connect and immediatlely disconnect. For the 2014 module, the IP connect status shows 2 then 5 and never connects again.?

For the CCD driver, there was not an exact match. FWD drivers seem to have only IR or serial support.?
Tried the XBR universal driver:?
FlatPanelDisplay_Sony_XBR-43X800H-SmartTV_IP.pkg
Strange that the CCD driver would get back 200 OK messages but there were no actual changes in control for the display.?
Log info below:?


Since there was so little time to get this working today, had to revert to 232. Of course, power control is good but the the vol and mute do not work. UGH !!?


----

0 ms: Display_Driver_FileLocation -> /User/CrestronCertifiedDrivers/App01/FlatPanelDisplay_Sony_XBR-43X800H-SmartTV_IP.pkg

0 ms: Display_IP_address -> 10.110.250.30

0 ms: Display_MAC_address -> F8:4E:17:25:79:14

0 ms: Display_OnScreenID -> Message Box Text

0 ms: Display_UserName$ -> root

0 ms: Display_Password$ -> admin

0 ms: Display_NumberOfInputs -> 4d

0 ms: Display_Info_Manufacturer_FB -> Sony

0 ms: Display_Info_BaseModel_FB -> XBR-43X800H SmartTV

0 ms: Display_Info_SupportedModels_FB -> XBR-43X800H SmartTV, FW-43BT30K SmartTV, FW-50BT30K SmartTV, FW-55BT30K SmartTV, FW-65BT30K SmartTV, FW-75BT30K SmartTV, KD-43X80K SmartTV, KD-43X81DK SmartTV, KD-43X81K SmartTV, KD-43X82K SmartTV, KD

0 ms: Display_Info_SupportedSeries_FB -> XBR Series,XR Series,XRJ Series,FW Series,KD Series,KE Series,KJ Series,KM Series

0 ms: Display_Info_Description_FB -> Sony XBR Series Display

0 ms: Display_UserAttribute_1_Label -> Warning Information

0 ms: Display_UserAttribute_1_Description -> The path to the settings below may vary slightly based on model and/or firmware version.

0 ms: Display_UserAttribute_2_Label -> Setup Instructions

0 ms: Display_UserAttribute_2_Description -> To enable IP control, Navigate to Settings > Network > Home Network > IP Control > Authentication and set to 'Normal and Pre-Shared Key'

0 ms: Display_UserAttribute_3_Label -> Pre-Shared Key needed for communication

0 ms: Display_UserAttribute_3_Description -> This is required to control the display. Settings > Network > Home Network > IP Control > Pre-Shared Key

0 ms: Display_UserAttribute_4_Label -> Setup Instructions

0 ms: Display_UserAttribute_4_Description -> The following must be Enabled for IP control, Navigate to Settings > Network > Home Network > IP Control > Simple IP Control

0 ms: Display_UserAttribute_5_Label -> Setup Instructions

0 ms: Display_UserAttribute_5_Description -> The following must also be 'ON' for IP control on some TVs, Navigate to Settings > Network > Home Network > Remote device/Renderer > Remote device/Renderer

0 ms: Display_Connection_F -> 1

0 ms: Display_SupportsPower_F -> 1

0 ms: Display_SupportsDiscretePower -> 1

0 ms: Display_SupportsTogglePower -> 1

0 ms: Display_Driver_Load_FB -> 1

0 ms: Display_volume_isSupported -> 1

0 ms: Display_volume_SetIsSupported -> 1

0 ms: Display_volume_ChangeIsSupported -> 1

0 ms: Display_volume_mute_supported_FB -> 1

0 ms: Display_volume_mute_discrete_supported_FB -> 1

0 ms: Display_volume_mute_toggle_supported_FB -> 1

0 ms: Display_InputType_1 -> 400d

0 ms: Display_InputType_2 -> 401d

0 ms: Display_InputType_3 -> 402d

0 ms: Display_InputType_4 -> 403d

0 ms: Display_InputDescription_1 -> HDMI 1

0 ms: Display_InputDescription_2 -> HDMI 2

0 ms: Display_InputDescription_3 -> HDMI 3

0 ms: Display_InputDescription_4 -> HDMI 4

0 ms: Display_Debug_Log_Output_FB -> MediaServiceProviderUpdated.Exists

0 ms: RoomA_sys_off-l -> 1

0 ms: tp1_shutdown_bar_level -> 65535d

0 ms: RoomA_sys_stateChange_nor -> 1

00:00:02.500: [Console Data] : MPC3-201>

00:00:02.516: Display_volume_level_FB -> 0d

00:00:02.828: Display_volume_level_FB -> 15d

00:00:02.860: Display_volume_level_FB -> 15d

00:00:02.922: Display_volume_level_FB -> 15d

00:01:01.203: [User Stimulus] : User set Display_Debug_EnableDebugRX to Press

00:01:01.250: Display_Debug_EnableDebugRX -> 1

00:01:03.078: [Console Data] : 001-00:07:05.243 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system

00:01:03.078: [Console Data] : HTTP/1.1 200 OK

00:01:03.078: [Console Data] : Content-Type: application/json

00:01:03.078: [Console Data] : Connection: keep-alive

00:01:03.078: [Console Data] : Content-Length: 40

00:01:03.078: [Console Data] : --------

00:01:03.078: [Console Data] : {"result":[{"status":"active"}],"id":55}

00:01:03.125: [User Stimulus] : User set Display_Debug_EnableDebugTX to Press

00:01:03.157: Display_Debug_EnableDebugTX -> 1

00:01:03.172: [Console Data] : 001-00:07:05.344 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent

00:01:03.172: [Console Data] : Headers:

00:01:03.172: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:03.172: [Console Data] : Content-Type: application/json

00:01:03.172: [Console Data] : Connection: Keep-Alive

00:01:03.172: [Console Data] : Content-Length: 71

00:01:03.172: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":56,"version": "1.0"}

00:01:03.203: [Console Data] : 001-00:07:05.371 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent

00:01:03.203: [Console Data] : HTTP/1.1 403 Forbidden

00:01:03.203: [Console Data] : Content-Type: application/json

00:01:03.203: [Console Data] : Connection: keep-alive

00:01:03.203: [Console Data] : Content-Length: 168

00:01:03.203: [Console Data] : --------

00:01:03.203: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":56}

00:01:03.469: [Console Data] : 001-00:07:05.645 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio

00:01:03.469: [Console Data] : Headers:

00:01:03.469: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:03.469: [Console Data] : Content-Type: application/json

00:01:03.469: [Console Data] : Connection: Keep-Alive

00:01:03.469: [Console Data] : Content-Length: 70

00:01:03.469: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":57,"version": "1.0"}

00:01:03.547: [Console Data] : 001-00:07:05.682 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio

00:01:03.547: [Console Data] : HTTP/1.1 200 OK

00:01:03.547: [Console Data] : Content-Type: application/json

00:01:03.547: [Console Data] : Connection: keep-alive

00:01:03.547: [Console Data] : Content-Length: 98

00:01:03.547: [Console Data] : --------

00:01:03.547: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":57}

00:01:05.485: [User Stimulus] : User set Display_Debug_EnableLogging to Press

00:01:05.532: Display_Debug_EnableLogging -> 1

00:01:07.110: [Console Data] : 001-00:07:09.273 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport

00:01:07.110: [Console Data] : 001-00:07:09.282 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system

00:01:07.110: [Console Data] : Headers:

00:01:07.110: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:07.110: [Console Data] : Content-Type: application/json

00:01:07.110: [Console Data] : Connection: Keep-Alive

00:01:07.110: [Console Data] : Content-Length: 64

00:01:07.110: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":58,"version": "1.0"}

00:01:07.141: [Console Data] : 001-00:07:09.305 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system

00:01:07.141: [Console Data] : HTTP/1.1 200 OK

00:01:07.141: [Console Data] : Content-Type: application/json

00:01:07.141: [Console Data] : Connection: keep-alive

00:01:07.141: [Console Data] : Content-Length: 40

00:01:07.141: [Console Data] : --------

00:01:07.141: [Console Data] : {"result":[{"status":"active"}],"id":58}

00:01:07.235: [Console Data] : 001-00:07:09.400 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport

00:01:07.235: [Console Data] : 001-00:07:09.410 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent

00:01:07.235: [Console Data] : Headers:

00:01:07.235: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:07.235: [Console Data] : Content-Type: application/json

00:01:07.235: [Console Data] : Connection: Keep-Alive

00:01:07.235: [Console Data] : Content-Length: 71

00:01:07.235: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":59,"version": "1.0"}

00:01:07.266: [Console Data] : 001-00:07:09.441 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent

00:01:07.266: [Console Data] : HTTP/1.1 403 Forbidden

00:01:07.266: [Console Data] : Content-Type: application/json

00:01:07.266: [Console Data] : Connection: keep-alive

00:01:07.266: [Console Data] : Content-Length: 168

00:01:07.266: [Console Data] : --------

00:01:07.266: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":59}

00:01:07.532: [Console Data] : 001-00:07:09.708 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport

00:01:07.547: [Console Data] : 001-00:07:09.717 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio

00:01:07.547: [Console Data] : Headers:

00:01:07.547: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:07.547: [Console Data] : Content-Type: application/json

00:01:07.547: [Console Data] : Connection: Keep-Alive

00:01:07.547: [Console Data] : Content-Length: 70

00:01:07.547: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":60,"version": "1.0"}

00:01:07.594: [Console Data] : 001-00:07:09.745 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio

00:01:07.594: [Console Data] : HTTP/1.1 200 OK

00:01:07.594: [Console Data] : Content-Type: application/json

00:01:07.594: [Console Data] : Connection: keep-alive

00:01:07.594: [Console Data] : Content-Length: 98

00:01:07.594: [Console Data] : --------

00:01:07.594: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":60}

00:01:07.672: [Console Data] : 001-00:07:09.838 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetEnergyStar' to transport

00:01:07.672: [Console Data] : 001-00:07:09.847 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system

00:01:07.672: [Console Data] : Headers:

00:01:07.672: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:07.672: [Console Data] : Content-Type: application/json

00:01:07.672: [Console Data] : Connection: Keep-Alive

00:01:07.672: [Console Data] : Content-Length: 68

00:01:07.672: [Console Data] : Content:{"method":"getPowerSavingMode","params":[],"id":61,"version": "1.0"}

00:01:07.703: [Console Data] : 001-00:07:09.872 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system

00:01:07.703: [Console Data] : HTTP/1.1 200 OK

00:01:07.703: [Console Data] : Content-Type: application/json

00:01:07.703: [Console Data] : Connection: keep-alive

00:01:07.703: [Console Data] : Content-Length: 35

00:01:07.703: [Console Data] : --------

00:01:07.703: [Console Data] : {"result":[{"mode":"off"}],"id":61}

00:01:11.172: [Console Data] : 001-00:07:13.345 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport

00:01:11.188: [Console Data] : 001-00:07:13.354 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system

00:01:11.188: [Console Data] : Headers:

00:01:11.188: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:11.188: [Console Data] : Content-Type: application/json

00:01:11.188: [Console Data] : Connection: Keep-Alive

00:01:11.188: [Console Data] : Content-Length: 64

00:01:11.188: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":62,"version": "1.0"}

00:01:11.219: [Console Data] : 001-00:07:13.385 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system

00:01:11.219: [Console Data] : HTTP/1.1 200 OK

00:01:11.219: [Console Data] : Content-Type: application/json

00:01:11.219: [Console Data] : Connection: keep-alive

00:01:11.219: [Console Data] : Content-Length: 40

00:01:11.219: [Console Data] : --------

00:01:11.219: [Console Data] : {"result":[{"status":"active"}],"id":62}

00:01:11.313: [Console Data] : 001-00:07:13.476 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport

00:01:11.313: [Console Data] : 001-00:07:13.485 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent

00:01:11.313: [Console Data] : Headers:

00:01:11.313: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:11.313: [Console Data] : Content-Type: application/json

00:01:11.313: [Console Data] : Connection: Keep-Alive

00:01:11.313: [Console Data] : Content-Length: 71

00:01:11.313: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":63,"version": "1.0"}

00:01:11.344: [Console Data] : 001-00:07:13.511 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent

00:01:11.344: [Console Data] : HTTP/1.1 403 Forbidden

00:01:11.344: [Console Data] : Content-Type: application/json

00:01:11.344: [Console Data] : Connection: keep-alive

00:01:11.344: [Console Data] : Content-Length: 168

00:01:11.344: [Console Data] : --------

00:01:11.344: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":63}

00:01:11.594: [Console Data] : 001-00:07:13.771 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport

00:01:11.610: [Console Data] : 001-00:07:13.780 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio

00:01:11.610: [Console Data] : Headers:

00:01:11.610: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:11.610: [Console Data] : Content-Type: application/json

00:01:11.610: [Console Data] : Connection: Keep-Alive

00:01:11.610: [Console Data] : Content-Length: 70

00:01:11.610: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":64,"version": "1.0"}

00:01:11.672: [Console Data] : 001-00:07:13.812 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio

00:01:11.672: [Console Data] : HTTP/1.1 200 OK

00:01:11.672: [Console Data] : Content-Type: application/json

00:01:11.672: [Console Data] : Connection: keep-alive

00:01:11.672: [Console Data] : Content-Length: 98

00:01:11.672: [Console Data] : --------

00:01:11.672: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":64}

00:01:15.250: [Console Data] : 001-00:07:17.415 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport

00:01:15.250: [Console Data] : 001-00:07:17.424 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system

00:01:15.250: [Console Data] : Headers:

00:01:15.250: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:15.250: [Console Data] : Content-Type: application/json

00:01:15.250: [Console Data] : Connection: Keep-Alive

00:01:15.250: [Console Data] : Content-Length: 64

00:01:15.250: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":65,"version": "1.0"}

00:01:15.282: [Console Data] : 001-00:07:17.451 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system

00:01:15.282: [Console Data] : HTTP/1.1 200 OK

00:01:15.282: [Console Data] : Content-Type: application/json

00:01:15.282: [Console Data] : Connection: keep-alive

00:01:15.282: [Console Data] : Content-Length: 40

00:01:15.282: [Console Data] : --------

00:01:15.282: [Console Data] : {"result":[{"status":"active"}],"id":65}

00:01:15.375: [Console Data] : 001-00:07:17.544 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport

00:01:15.391: [Console Data] : 001-00:07:17.553 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent

00:01:15.391: [Console Data] : Headers:

00:01:15.391: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:15.391: [Console Data] : Content-Type: application/json

00:01:15.391: [Console Data] : Connection: Keep-Alive

00:01:15.391: [Console Data] : Content-Length: 71

00:01:15.391: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":66,"version": "1.0"}

00:01:15.407: [Console Data] : 001-00:07:17.578 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent

00:01:15.407: [Console Data] : HTTP/1.1 403 Forbidden

00:01:15.407: [Console Data] : Content-Type: application/json

00:01:15.407: [Console Data] : Connection: keep-alive

00:01:15.407: [Console Data] : Content-Length: 168

00:01:15.407: [Console Data] : --------

00:01:15.407: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":66}

00:01:15.672: [Console Data] : 001-00:07:17.834 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport

00:01:15.672: [Console Data] : 001-00:07:17.843 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio

00:01:15.672: [Console Data] : Headers:

00:01:15.672: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:15.672: [Console Data] : Content-Type: application/json

00:01:15.672: [Console Data] : Connection: Keep-Alive

00:01:15.672: [Console Data] : Content-Length: 70

00:01:15.672: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":67,"version": "1.0"}

00:01:15.703: [Console Data] : 001-00:07:17.874 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio

00:01:15.703: [Console Data] : HTTP/1.1 200 OK

00:01:15.703: [Console Data] : Content-Type: application/json

00:01:15.703: [Console Data] : Connection: keep-alive

00:01:15.703: [Console Data] : Content-Length: 98

00:01:15.703: [Console Data] : --------

00:01:15.703: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":67}

00:01:15.797: [Console Data] : 001-00:07:17.964 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetEnergyStar' to transport

00:01:15.797: [Console Data] : 001-00:07:17.973 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system

00:01:15.797: [Console Data] : Headers:

00:01:15.797: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:15.797: [Console Data] : Content-Type: application/json

00:01:15.797: [Console Data] : Connection: Keep-Alive

00:01:15.797: [Console Data] : Content-Length: 68

00:01:15.797: [Console Data] : Content:{"method":"getPowerSavingMode","params":[],"id":68,"version": "1.0"}

00:01:15.828: [Console Data] : 001-00:07:18.002 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system

00:01:15.828: [Console Data] : HTTP/1.1 200 OK

00:01:15.828: [Console Data] : Content-Type: application/json

00:01:15.828: [Console Data] : Connection: keep-alive

00:01:15.828: [Console Data] : Content-Length: 35

00:01:15.828: [Console Data] : --------

00:01:15.828: [Console Data] : {"result":[{"mode":"off"}],"id":68}

00:01:19.297: [Console Data] : 001-00:07:21.470 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport

00:01:19.313: [Console Data] : 001-00:07:21.479 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system

00:01:19.313: [Console Data] : Headers:

00:01:19.313: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:19.313: [Console Data] : Content-Type: application/json

00:01:19.313: [Console Data] : Connection: Keep-Alive

00:01:19.313: [Console Data] : Content-Length: 64

00:01:19.313: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":69,"version": "1.0"}

00:01:19.344: [Console Data] : 001-00:07:21.505 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system

00:01:19.344: [Console Data] : HTTP/1.1 200 OK

00:01:19.344: [Console Data] : Content-Type: application/json

00:01:19.344: [Console Data] : Connection: keep-alive

00:01:19.344: [Console Data] : Content-Length: 40

00:01:19.344: [Console Data] : --------

00:01:19.344: [Console Data] : {"result":[{"status":"active"}],"id":69}

00:01:19.438: [Console Data] : 001-00:07:21.599 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport

00:01:19.438: [Console Data] : 001-00:07:21.610 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent

00:01:19.438: [Console Data] : Headers:

00:01:19.438: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:19.438: [Console Data] : Content-Type: application/json

00:01:19.438: [Console Data] : Connection: Keep-Alive

00:01:19.438: [Console Data] : Content-Length: 71

00:01:19.438: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":70,"version": "1.0"}

00:01:19.485: [Console Data] : 001-00:07:21.643 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent

00:01:19.485: [Console Data] : HTTP/1.1 403 Forbidden

00:01:19.485: [Console Data] : Content-Type: application/json

00:01:19.485: [Console Data] : Connection: keep-alive

00:01:19.485: [Console Data] : Content-Length: 168

00:01:19.485: [Console Data] : --------

00:01:19.485: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":70}

00:01:19.735: [Console Data] : 001-00:07:21.907 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport

00:01:19.750: [Console Data] : 001-00:07:21.915 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio

00:01:19.750: [Console Data] : Headers:

00:01:19.750: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:19.750: [Console Data] : Content-Type: application/json

00:01:19.750: [Console Data] : Connection: Keep-Alive

00:01:19.750: [Console Data] : Content-Length: 70

00:01:19.750: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":71,"version": "1.0"}

00:01:19.813: [Console Data] : 001-00:07:21.944 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio

00:01:19.813: [Console Data] : HTTP/1.1 200 OK

00:01:19.813: [Console Data] : Content-Type: application/json

00:01:19.813: [Console Data] : Connection: keep-alive

00:01:19.813: [Console Data] : Content-Length: 98

00:01:19.813: [Console Data] : --------

00:01:19.813: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":71}

00:01:23.360: [Console Data] : 001-00:07:25.526 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport

00:01:23.360: [Console Data] : 001-00:07:25.536 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system

00:01:23.360: [Console Data] : Headers:

00:01:23.360: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:23.360: [Console Data] : Content-Type: application/json

00:01:23.360: [Console Data] : Connection: Keep-Alive

00:01:23.360: [Console Data] : Content-Length: 64

00:01:23.360: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":72,"version": "1.0"}

00:01:23.391: [Console Data] : 001-00:07:25.561 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system

00:01:23.391: [Console Data] : HTTP/1.1 200 OK

00:01:23.391: [Console Data] : Content-Type: application/json

00:01:23.391: [Console Data] : Connection: keep-alive

00:01:23.391: [Console Data] : Content-Length: 40

00:01:23.391: [Console Data] : --------

00:01:23.391: [Console Data] : {"result":[{"status":"active"}],"id":72}

00:01:23.500: [Console Data] : 001-00:07:25.655 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport

00:01:23.516: [Console Data] : 001-00:07:25.664 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent

00:01:23.516: [Console Data] : Headers:

00:01:23.516: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:23.516: [Console Data] : Content-Type: application/json

00:01:23.516: [Console Data] : Connection: Keep-Alive

00:01:23.516: [Console Data] : Content-Length: 71

00:01:23.516: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":73,"version": "1.0"}

00:01:23.516: [Console Data] : 001-00:07:25.687 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent

00:01:23.516: [Console Data] : HTTP/1.1 403 Forbidden

00:01:23.516: [Console Data] : Content-Type: application/json

00:01:23.516: [Console Data] : Connection: keep-alive

00:01:23.516: [Console Data] : Content-Length: 168

00:01:23.516: [Console Data] : --------

00:01:23.516: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":73}

00:01:23.813: [Console Data] : 001-00:07:25.987 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport

00:01:23.828: [Console Data] : 001-00:07:25.997 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio

00:01:23.828: [Console Data] : Headers:

00:01:23.828: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:23.828: [Console Data] : Content-Type: application/json

00:01:23.828: [Console Data] : Connection: Keep-Alive

00:01:23.828: [Console Data] : Content-Length: 70

00:01:23.828: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":74,"version": "1.0"}

00:01:23.875: [Console Data] : 001-00:07:26.034 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio

00:01:23.875: [Console Data] : HTTP/1.1 200 OK

00:01:23.875: [Console Data] : Content-Type: application/json

00:01:23.875: [Console Data] : Connection: keep-alive

00:01:23.875: [Console Data] : Content-Length: 98

00:01:23.875: [Console Data] : --------

00:01:23.875: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":74}

00:01:23.953: [Console Data] : 001-00:07:26.126 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetEnergyStar' to transport

00:01:23.969: [Console Data] : 001-00:07:26.134 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system

00:01:23.969: [Console Data] : Headers:

00:01:23.969: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:23.969: [Console Data] : Content-Type: application/json

00:01:23.969: [Console Data] : Connection: Keep-Alive

00:01:23.969: [Console Data] : Content-Length: 68

00:01:23.969: [Console Data] : Content:{"method":"getPowerSavingMode","params":[],"id":75,"version": "1.0"}

00:01:24.000: [Console Data] : 001-00:07:26.161 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system

00:01:24.000: [Console Data] : HTTP/1.1 200 OK

00:01:24.000: [Console Data] : Content-Type: application/json

00:01:24.000: [Console Data] : Connection: close

00:01:24.000: [Console Data] : Content-Length: 35

00:01:24.000: [Console Data] : --------

00:01:24.000: [Console Data] : {"result":[{"mode":"off"}],"id":75}

00:01:27.407: [Console Data] : 001-00:07:29.580 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport

00:01:27.422: [Console Data] : 001-00:07:29.591 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system

00:01:27.422: [Console Data] : Headers:

00:01:27.422: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:27.422: [Console Data] : Content-Type: application/json

00:01:27.422: [Console Data] : Connection: Keep-Alive

00:01:27.422: [Console Data] : Content-Length: 64

00:01:27.422: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":76,"version": "1.0"}

00:01:27.453: [Console Data] : 001-00:07:29.629 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system

00:01:27.453: [Console Data] : HTTP/1.1 200 OK

00:01:27.453: [Console Data] : Content-Type: application/json

00:01:27.453: [Console Data] : Connection: keep-alive

00:01:27.453: [Console Data] : Content-Length: 40

00:01:27.453: [Console Data] : --------

00:01:27.453: [Console Data] : {"result":[{"status":"active"}],"id":76}

00:01:27.547: [Console Data] : 001-00:07:29.718 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport

00:01:27.563: [Console Data] : 001-00:07:29.726 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent

00:01:27.563: [Console Data] : Headers:

00:01:27.563: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:27.563: [Console Data] : Content-Type: application/json

00:01:27.563: [Console Data] : Connection: Keep-Alive

00:01:27.563: [Console Data] : Content-Length: 71

00:01:27.563: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":77,"version": "1.0"}

00:01:27.578: [Console Data] : 001-00:07:29.753 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent

00:01:27.578: [Console Data] : HTTP/1.1 403 Forbidden

00:01:27.578: [Console Data] : Content-Type: application/json

00:01:27.578: [Console Data] : Connection: keep-alive

00:01:27.578: [Console Data] : Content-Length: 168

00:01:27.578: [Console Data] : --------

00:01:27.578: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":77}

00:01:27.891: [Console Data] : 001-00:07:30.059 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport

00:01:27.907: [Console Data] : 001-00:07:30.067 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio

00:01:27.907: [Console Data] : Headers:

00:01:27.907: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:27.907: [Console Data] : Content-Type: application/json

00:01:27.907: [Console Data] : Connection: Keep-Alive

00:01:27.907: [Console Data] : Content-Length: 70

00:01:27.907: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":78,"version": "1.0"}

00:01:27.922: [Console Data] : 001-00:07:30.098 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio

00:01:27.922: [Console Data] : HTTP/1.1 200 OK

00:01:27.922: [Console Data] : Content-Type: application/json

00:01:27.922: [Console Data] : Connection: keep-alive

00:01:27.922: [Console Data] : Content-Length: 98

00:01:27.922: [Console Data] : --------

00:01:27.922: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":78}

00:01:31.485: [Console Data] : 001-00:07:33.650 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport

00:01:31.485: [Console Data] : 001-00:07:33.659 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system

00:01:31.485: [Console Data] : Headers:

00:01:31.485: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:31.485: [Console Data] : Content-Type: application/json

00:01:31.485: [Console Data] : Connection: Keep-Alive

00:01:31.485: [Console Data] : Content-Length: 64

00:01:31.485: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":79,"version": "1.0"}

00:01:31.516: [Console Data] : 001-00:07:33.686 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system

00:01:31.516: [Console Data] : HTTP/1.1 200 OK

00:01:31.516: [Console Data] : Content-Type: application/json

00:01:31.516: [Console Data] : Connection: keep-alive

00:01:31.516: [Console Data] : Content-Length: 40

00:01:31.516: [Console Data] : --------

00:01:31.516: [Console Data] : {"result":[{"status":"active"}],"id":79}

00:01:31.610: [Console Data] : 001-00:07:33.779 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport

00:01:31.625: [Console Data] : 001-00:07:33.790 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent

00:01:31.625: [Console Data] : Headers:

00:01:31.625: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:31.625: [Console Data] : Content-Type: application/json

00:01:31.625: [Console Data] : Connection: Keep-Alive

00:01:31.625: [Console Data] : Content-Length: 71

00:01:31.625: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":80,"version": "1.0"}

00:01:31.657: [Console Data] : 001-00:07:33.824 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent

00:01:31.657: [Console Data] : HTTP/1.1 403 Forbidden

00:01:31.657: [Console Data] : Content-Type: application/json

00:01:31.657: [Console Data] : Connection: keep-alive

00:01:31.657: [Console Data] : Content-Length: 168

00:01:31.657: [Console Data] : --------

00:01:31.657: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":80}

00:01:31.953: [Console Data] : 001-00:07:34.121 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport

00:01:31.969: [Console Data] : 001-00:07:34.132 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio

00:01:31.969: [Console Data] : Headers:

00:01:31.969: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:31.969: [Console Data] : Content-Type: application/json

00:01:31.969: [Console Data] : Connection: Keep-Alive

00:01:31.969: [Console Data] : Content-Length: 70

00:01:31.969: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":81,"version": "1.0"}

00:01:32.000: [Console Data] : 001-00:07:34.172 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio

00:01:32.000: [Console Data] : HTTP/1.1 200 OK

00:01:32.000: [Console Data] : Content-Type: application/json

00:01:32.000: [Console Data] : Connection: keep-alive

00:01:32.000: [Console Data] : Content-Length: 98

00:01:32.000: [Console Data] : --------

00:01:32.000: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":81}

00:01:32.078: [Console Data] : 001-00:07:34.251 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetEnergyStar' to transport

00:01:32.094: [Console Data] : 001-00:07:34.260 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system

00:01:32.094: [Console Data] : Headers:

00:01:32.094: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:32.094: [Console Data] : Content-Type: application/json

00:01:32.094: [Console Data] : Connection: Keep-Alive

00:01:32.094: [Console Data] : Content-Length: 68

00:01:32.094: [Console Data] : Content:{"method":"getPowerSavingMode","params":[],"id":82,"version": "1.0"}

00:01:32.125: [Console Data] : 001-00:07:34.289 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system

00:01:32.125: [Console Data] : HTTP/1.1 200 OK

00:01:32.125: [Console Data] : Content-Type: application/json

00:01:32.125: [Console Data] : Connection: keep-alive

00:01:32.125: [Console Data] : Content-Length: 35

00:01:32.125: [Console Data] : --------

00:01:32.125: [Console Data] : {"result":[{"mode":"off"}],"id":82}

00:01:35.532: [Console Data] : 001-00:07:37.707 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport

00:01:35.547: [Console Data] : 001-00:07:37.716 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system

00:01:35.547: [Console Data] : Headers:

00:01:35.547: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:35.547: [Console Data] : Content-Type: application/json

00:01:35.547: [Console Data] : Connection: Keep-Alive

00:01:35.547: [Console Data] : Content-Length: 64

00:01:35.547: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":83,"version": "1.0"}

00:01:35.578: [Console Data] : 001-00:07:37.748 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system

00:01:35.578: [Console Data] : HTTP/1.1 200 OK

00:01:35.578: [Console Data] : Content-Type: application/json

00:01:35.578: [Console Data] : Connection: keep-alive

00:01:35.578: [Console Data] : Content-Length: 40

00:01:35.578: [Console Data] : --------

00:01:35.578: [Console Data] : {"result":[{"status":"active"}],"id":83}

00:01:35.672: [Console Data] : 001-00:07:37.836 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport

00:01:35.672: [Console Data] : 001-00:07:37.844 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent

00:01:35.672: [Console Data] : Headers:

00:01:35.672: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:35.672: [Console Data] : Content-Type: application/json

00:01:35.672: [Console Data] : Connection: Keep-Alive

00:01:35.672: [Console Data] : Content-Length: 71

00:01:35.672: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":84,"version": "1.0"}

00:01:35.703: [Console Data] : 001-00:07:37.873 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent

00:01:35.703: [Console Data] : HTTP/1.1 403 Forbidden

00:01:35.703: [Console Data] : Content-Type: application/json

00:01:35.703: [Console Data] : Connection: keep-alive

00:01:35.703: [Console Data] : Content-Length: 168

00:01:35.703: [Console Data] : --------

00:01:35.703: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":84}

00:01:36.016: [Console Data] : 001-00:07:38.194 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport

00:01:36.032: [Console Data] : 001-00:07:38.202 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio

00:01:36.032: [Console Data] : Headers:

00:01:36.032: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:36.032: [Console Data] : Content-Type: application/json

00:01:36.032: [Console Data] : Connection: Keep-Alive

00:01:36.032: [Console Data] : Content-Length: 70

00:01:36.032: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":85,"version": "1.0"}

00:01:36.094: [Console Data] : 001-00:07:38.261 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio

00:01:36.094: [Console Data] : HTTP/1.1 200 OK

00:01:36.094: [Console Data] : Content-Type: application/json

00:01:36.094: [Console Data] : Connection: keep-alive

00:01:36.094: [Console Data] : Content-Length: 98

00:01:36.094: [Console Data] : --------

00:01:36.094: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":85}

00:01:39.610: [Console Data] : 001-00:07:41.773 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport

00:01:39.610: [Console Data] : 001-00:07:41.782 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system

00:01:39.610: [Console Data] : Headers:

00:01:39.610: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:39.610: [Console Data] : Content-Type: application/json

00:01:39.610: [Console Data] : Connection: Keep-Alive

00:01:39.610: [Console Data] : Content-Length: 64

00:01:39.610: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":86,"version": "1.0"}

00:01:39.657: [Console Data] : 001-00:07:41.819 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system

00:01:39.657: [Console Data] : HTTP/1.1 200 OK

00:01:39.657: [Console Data] : Content-Type: application/json

00:01:39.657: [Console Data] : Connection: keep-alive

00:01:39.657: [Console Data] : Content-Length: 40

00:01:39.657: [Console Data] : --------

00:01:39.657: [Console Data] : {"result":[{"status":"active"}],"id":86}

00:01:39.735: [Console Data] : 001-00:07:41.910 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport

00:01:39.750: [Console Data] : 001-00:07:41.919 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent

00:01:39.750: [Console Data] : Headers:

00:01:39.750: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:39.750: [Console Data] : Content-Type: application/json

00:01:39.750: [Console Data] : Connection: Keep-Alive

00:01:39.750: [Console Data] : Content-Length: 71

00:01:39.750: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":87,"version": "1.0"}

00:01:39.782: [Console Data] : 001-00:07:41.947 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent

00:01:39.782: [Console Data] : HTTP/1.1 403 Forbidden

00:01:39.782: [Console Data] : Content-Type: application/json

00:01:39.782: [Console Data] : Connection: keep-alive

00:01:39.782: [Console Data] : Content-Length: 168

00:01:39.782: [Console Data] : --------

00:01:39.782: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":87}

00:01:40.110: [Console Data] : 001-00:07:42.285 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport

00:01:40.125: [Console Data] : 001-00:07:42.302 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio

00:01:40.125: [Console Data] : Headers:

00:01:40.125: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:40.125: [Console Data] : Content-Type: application/json

00:01:40.125: [Console Data] : Connection: Keep-Alive

00:01:40.125: [Console Data] : Content-Length: 70

00:01:40.125: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":88,"version": "1.0"}

00:01:40.172: [Console Data] : 001-00:07:42.332 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio

00:01:40.172: [Console Data] : HTTP/1.1 200 OK

00:01:40.172: [Console Data] : Content-Type: application/json

00:01:40.172: [Console Data] : Connection: keep-alive

00:01:40.172: [Console Data] : Content-Length: 98

00:01:40.172: [Console Data] : --------

00:01:40.172: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":88}

00:01:40.250: [Console Data] : 001-00:07:42.422 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetEnergyStar' to transport

00:01:40.266: [Console Data] : 001-00:07:42.430 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system

00:01:40.266: [Console Data] : Headers:

00:01:40.266: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:40.266: [Console Data] : Content-Type: application/json

00:01:40.266: [Console Data] : Connection: Keep-Alive

00:01:40.266: [Console Data] : Content-Length: 68

00:01:40.266: [Console Data] : Content:{"method":"getPowerSavingMode","params":[],"id":89,"version": "1.0"}

00:01:40.297: [Console Data] : 001-00:07:42.459 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system

00:01:40.297: [Console Data] : HTTP/1.1 200 OK

00:01:40.297: [Console Data] : Content-Type: application/json

00:01:40.297: [Console Data] : Connection: keep-alive

00:01:40.297: [Console Data] : Content-Length: 35

00:01:40.297: [Console Data] : --------

00:01:40.297: [Console Data] : {"result":[{"mode":"off"}],"id":89}

00:01:43.672: [Console Data] : 001-00:07:45.839 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport

00:01:43.672: [Console Data] : 001-00:07:45.848 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system

00:01:43.672: [Console Data] : Headers:

00:01:43.672: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:43.672: [Console Data] : Content-Type: application/json

00:01:43.672: [Console Data] : Connection: Keep-Alive

00:01:43.672: [Console Data] : Content-Length: 64

00:01:43.672: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":90,"version": "1.0"}

00:01:43.719: [Console Data] : 001-00:07:45.880 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system

00:01:43.719: [Console Data] : HTTP/1.1 200 OK

00:01:43.719: [Console Data] : Content-Type: application/json

00:01:43.719: [Console Data] : Connection: keep-alive

00:01:43.719: [Console Data] : Content-Length: 40

00:01:43.719: [Console Data] : --------

00:01:43.719: [Console Data] : {"result":[{"status":"active"}],"id":90}

00:01:43.797: [Console Data] : 001-00:07:45.967 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport

00:01:43.813: [Console Data] : 001-00:07:45.976 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent

00:01:43.813: [Console Data] : Headers:

00:01:43.813: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:43.813: [Console Data] : Content-Type: application/json

00:01:43.813: [Console Data] : Connection: Keep-Alive

00:01:43.813: [Console Data] : Content-Length: 71

00:01:43.813: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":91,"version": "1.0"}

00:01:43.844: [Console Data] : 001-00:07:46.006 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent

00:01:43.844: [Console Data] : HTTP/1.1 403 Forbidden

00:01:43.844: [Console Data] : Content-Type: application/json

00:01:43.844: [Console Data] : Connection: keep-alive

00:01:43.844: [Console Data] : Content-Length: 168

00:01:43.844: [Console Data] : --------

00:01:43.844: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":91}

00:01:44.188: [Console Data] : 001-00:07:46.356 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport

00:01:44.188: [Console Data] : 001-00:07:46.364 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio

00:01:44.188: [Console Data] : Headers:

00:01:44.188: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:44.188: [Console Data] : Content-Type: application/json

00:01:44.188: [Console Data] : Connection: Keep-Alive

00:01:44.188: [Console Data] : Content-Length: 70

00:01:44.188: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":92,"version": "1.0"}

00:01:44.219: [Console Data] : 001-00:07:46.395 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio

00:01:44.219: [Console Data] : HTTP/1.1 200 OK

00:01:44.219: [Console Data] : Content-Type: application/json

00:01:44.219: [Console Data] : Connection: keep-alive

00:01:44.219: [Console Data] : Content-Length: 98

00:01:44.219: [Console Data] : --------

00:01:44.219: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":92}

00:01:47.735: [Console Data] : 001-00:07:49.901 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport

00:01:47.735: [Console Data] : 001-00:07:49.910 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system

00:01:47.735: [Console Data] : Headers:

00:01:47.735: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:47.735: [Console Data] : Content-Type: application/json

00:01:47.735: [Console Data] : Connection: Keep-Alive

00:01:47.735: [Console Data] : Content-Length: 64

00:01:47.735: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":93,"version": "1.0"}

00:01:47.766: [Console Data] : 001-00:07:49.939 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system

00:01:47.766: [Console Data] : HTTP/1.1 200 OK

00:01:47.766: [Console Data] : Content-Type: application/json

00:01:47.766: [Console Data] : Connection: keep-alive

00:01:47.766: [Console Data] : Content-Length: 40

00:01:47.766: [Console Data] : --------

00:01:47.766: [Console Data] : {"result":[{"status":"active"}],"id":93}

00:01:47.860: [Console Data] : 001-00:07:50.029 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport

00:01:47.875: [Console Data] : 001-00:07:50.040 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent

00:01:47.875: [Console Data] : Headers:

00:01:47.875: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:47.875: [Console Data] : Content-Type: application/json

00:01:47.875: [Console Data] : Connection: Keep-Alive

00:01:47.875: [Console Data] : Content-Length: 71

00:01:47.875: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":94,"version": "1.0"}

00:01:47.907: [Console Data] : 001-00:07:50.077 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent

00:01:47.907: [Console Data] : HTTP/1.1 403 Forbidden

00:01:47.907: [Console Data] : Content-Type: application/json

00:01:47.907: [Console Data] : Connection: keep-alive

00:01:47.907: [Console Data] : Content-Length: 168

00:01:47.907: [Console Data] : --------

00:01:47.907: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":94}

00:01:48.250: [Console Data] : 001-00:07:50.418 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport

00:01:48.250: [Console Data] : 001-00:07:50.427 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio

00:01:48.250: [Console Data] : Headers:

00:01:48.250: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:48.250: [Console Data] : Content-Type: application/json

00:01:48.250: [Console Data] : Connection: Keep-Alive

00:01:48.250: [Console Data] : Content-Length: 70

00:01:48.250: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":95,"version": "1.0"}

00:01:48.297: [Console Data] : 001-00:07:50.461 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio

00:01:48.297: [Console Data] : HTTP/1.1 200 OK

00:01:48.297: [Console Data] : Content-Type: application/json

00:01:48.297: [Console Data] : Connection: keep-alive

00:01:48.297: [Console Data] : Content-Length: 98

00:01:48.297: [Console Data] : --------

00:01:48.297: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":95}

00:01:48.375: [Console Data] : 001-00:07:50.548 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetEnergyStar' to transport

00:01:48.391: [Console Data] : 001-00:07:50.564 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system

00:01:48.391: [Console Data] : Headers:

00:01:48.391: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14

00:01:48.391: [Console Data] : Content-Type: application/json

00:01:48.391: [Console Data] : Connection: Keep-Alive

00:01:48.391: [Console Data] : Content-Length: 68

00:01:48.391: [Console Data] : Content:{"method":"getPowerSavingMode","params":[],"id":96,"version": "1.0"}

00:01:48.422: [Console Data] : 001-00:07:50.595 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system

00:01:48.422: [Console Data] : HTTP/1.1 200 OK

00:01:48.422: [Console Data] : Content-Type: application/json

00:01:48.422: [Console Data] : Connection: keep-alive

00:01:48.422: [Console Data] : Content-Length: 35

00:01:48.422: [Console Data] : --------

00:01:48.422: [Console Data] : {"result":[{"mode":"off"}],"id":96}?


Re: WattBox WB-150-IPW-1B-2 and Crestron driver - Checking for power #simplwindows #crestron #poll

 

Although I don't have much experience with the WiFi units (primarily just the ethernet units), it should operate essentially the same.
The v1.9 module provides for real outlet status feedback (output: OUTLET_STATES(x) ) that could be taken directly to the touchpanel feedback input.? Polling the module will update this if necessary. I'm not sure that it even needs polling for update though I haven't messed with it recently...
If you're using an INTERLOCK symbol for the feedback, driven by your touchpanel button presses, the outputs of the symbol are all low at program start and will only be raised when an input is triggered.

I would try bringing signals directly to/from the touchpanel to the module and see how that behaves...


Re: Sony Professional Display problems.

 

Cannot get IP control to work at all for FWD-65X81CH.?

Used the Bravia 2014 module and also tried the Crestron CCD driver.?
Would connect and immediatlely disconnect. For the 2014 module, the IP connect status shows 2 then 5 and never connects again.?

For the CCD driver, there was not an exact match. FWD drivers seem to have only IR or serial support.?
Tried the XBR universal driver:?
FlatPanelDisplay_Sony_XBR-43X800H-SmartTV_IP.pkg
Strange that the CCD driver would get back 200 OK messages but there were no actual changes in control for the display.?
Log info below:?


Since there was so little time to get this working today, had to revert to 232. Of course, power control is good but the the vol and mute do not work. UGH !!?


----


0 ms: Display_Driver_FileLocation -> /User/CrestronCertifiedDrivers/App01/FlatPanelDisplay_Sony_XBR-43X800H-SmartTV_IP.pkg
0 ms: Display_IP_address -> 10.110.250.30
0 ms: Display_MAC_address -> F8:4E:17:25:79:14
0 ms: Display_OnScreenID -> Message Box Text
0 ms: Display_UserName$ -> root
0 ms: Display_Password$ -> admin
0 ms: Display_NumberOfInputs -> 4d
0 ms: Display_Info_Manufacturer_FB -> Sony
0 ms: Display_Info_BaseModel_FB -> XBR-43X800H SmartTV
0 ms: Display_Info_SupportedModels_FB -> XBR-43X800H SmartTV, FW-43BT30K SmartTV, FW-50BT30K SmartTV, FW-55BT30K SmartTV, FW-65BT30K SmartTV, FW-75BT30K SmartTV, KD-43X80K SmartTV, KD-43X81DK SmartTV, KD-43X81K SmartTV, KD-43X82K SmartTV, KD
0 ms: Display_Info_SupportedSeries_FB -> XBR Series,XR Series,XRJ Series,FW Series,KD Series,KE Series,KJ Series,KM Series
0 ms: Display_Info_Description_FB -> Sony XBR Series Display
0 ms: Display_UserAttribute_1_Label -> Warning Information
0 ms: Display_UserAttribute_1_Description -> The path to the settings below may vary slightly based on model and/or firmware version.
0 ms: Display_UserAttribute_2_Label -> Setup Instructions
0 ms: Display_UserAttribute_2_Description -> To enable IP control, Navigate to Settings > Network > Home Network > IP Control > Authentication and set to 'Normal and Pre-Shared Key'
0 ms: Display_UserAttribute_3_Label -> Pre-Shared Key needed for communication
0 ms: Display_UserAttribute_3_Description -> This is required to control the display. Settings > Network > Home Network > IP Control > Pre-Shared Key
0 ms: Display_UserAttribute_4_Label -> Setup Instructions
0 ms: Display_UserAttribute_4_Description -> The following must be Enabled for IP control, Navigate to Settings > Network > Home Network > IP Control > Simple IP Control
0 ms: Display_UserAttribute_5_Label -> Setup Instructions
0 ms: Display_UserAttribute_5_Description -> The following must also be 'ON' for IP control on some TVs, Navigate to Settings > Network > Home Network > Remote device/Renderer > Remote device/Renderer
0 ms: Display_Connection_F -> 1
0 ms: Display_SupportsPower_F -> 1
0 ms: Display_SupportsDiscretePower -> 1
0 ms: Display_SupportsTogglePower -> 1
0 ms: Display_Driver_Load_FB -> 1
0 ms: Display_volume_isSupported -> 1
0 ms: Display_volume_SetIsSupported -> 1
0 ms: Display_volume_ChangeIsSupported -> 1
0 ms: Display_volume_mute_supported_FB -> 1
0 ms: Display_volume_mute_discrete_supported_FB -> 1
0 ms: Display_volume_mute_toggle_supported_FB -> 1
0 ms: Display_InputType_1 -> 400d
0 ms: Display_InputType_2 -> 401d
0 ms: Display_InputType_3 -> 402d
0 ms: Display_InputType_4 -> 403d
0 ms: Display_InputDescription_1 -> HDMI 1
0 ms: Display_InputDescription_2 -> HDMI 2
0 ms: Display_InputDescription_3 -> HDMI 3
0 ms: Display_InputDescription_4 -> HDMI 4
0 ms: Display_Debug_Log_Output_FB -> MediaServiceProviderUpdated.Exists
0 ms: RoomA_sys_off-l -> 1
0 ms: tp1_shutdown_bar_level -> 65535d
0 ms: RoomA_sys_stateChange_nor -> 1
00:00:02.500: [Console Data] : MPC3-201>
00:00:02.516: Display_volume_level_FB -> 0d
00:00:02.828: Display_volume_level_FB -> 15d
00:00:02.860: Display_volume_level_FB -> 15d
00:00:02.922: Display_volume_level_FB -> 15d
00:01:01.203: [User Stimulus] : User set Display_Debug_EnableDebugRX to Press
00:01:01.250: Display_Debug_EnableDebugRX -> 1
00:01:03.078: [Console Data] : 001-00:07:05.243 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system
00:01:03.078: [Console Data] : HTTP/1.1 200 OK
00:01:03.078: [Console Data] : Content-Type: application/json
00:01:03.078: [Console Data] : Connection: keep-alive
00:01:03.078: [Console Data] : Content-Length: 40
00:01:03.078: [Console Data] : --------
00:01:03.078: [Console Data] : {"result":[{"status":"active"}],"id":55}
00:01:03.125: [User Stimulus] : User set Display_Debug_EnableDebugTX to Press
00:01:03.157: Display_Debug_EnableDebugTX -> 1
00:01:03.172: [Console Data] : 001-00:07:05.344 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent
00:01:03.172: [Console Data] : Headers:
00:01:03.172: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:03.172: [Console Data] : Content-Type: application/json
00:01:03.172: [Console Data] : Connection: Keep-Alive
00:01:03.172: [Console Data] : Content-Length: 71
00:01:03.172: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":56,"version": "1.0"}
00:01:03.203: [Console Data] : 001-00:07:05.371 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent
00:01:03.203: [Console Data] : HTTP/1.1 403 Forbidden
00:01:03.203: [Console Data] : Content-Type: application/json
00:01:03.203: [Console Data] : Connection: keep-alive
00:01:03.203: [Console Data] : Content-Length: 168
00:01:03.203: [Console Data] : --------
00:01:03.203: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":56}
00:01:03.469: [Console Data] : 001-00:07:05.645 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio
00:01:03.469: [Console Data] : Headers:
00:01:03.469: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:03.469: [Console Data] : Content-Type: application/json
00:01:03.469: [Console Data] : Connection: Keep-Alive
00:01:03.469: [Console Data] : Content-Length: 70
00:01:03.469: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":57,"version": "1.0"}
00:01:03.547: [Console Data] : 001-00:07:05.682 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio
00:01:03.547: [Console Data] : HTTP/1.1 200 OK
00:01:03.547: [Console Data] : Content-Type: application/json
00:01:03.547: [Console Data] : Connection: keep-alive
00:01:03.547: [Console Data] : Content-Length: 98
00:01:03.547: [Console Data] : --------
00:01:03.547: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":57}
00:01:05.485: [User Stimulus] : User set Display_Debug_EnableLogging to Press
00:01:05.532: Display_Debug_EnableLogging -> 1
00:01:07.110: [Console Data] : 001-00:07:09.273 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport
00:01:07.110: [Console Data] : 001-00:07:09.282 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system
00:01:07.110: [Console Data] : Headers:
00:01:07.110: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:07.110: [Console Data] : Content-Type: application/json
00:01:07.110: [Console Data] : Connection: Keep-Alive
00:01:07.110: [Console Data] : Content-Length: 64
00:01:07.110: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":58,"version": "1.0"}
00:01:07.141: [Console Data] : 001-00:07:09.305 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system
00:01:07.141: [Console Data] : HTTP/1.1 200 OK
00:01:07.141: [Console Data] : Content-Type: application/json
00:01:07.141: [Console Data] : Connection: keep-alive
00:01:07.141: [Console Data] : Content-Length: 40
00:01:07.141: [Console Data] : --------
00:01:07.141: [Console Data] : {"result":[{"status":"active"}],"id":58}
00:01:07.235: [Console Data] : 001-00:07:09.400 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport
00:01:07.235: [Console Data] : 001-00:07:09.410 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent
00:01:07.235: [Console Data] : Headers:
00:01:07.235: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:07.235: [Console Data] : Content-Type: application/json
00:01:07.235: [Console Data] : Connection: Keep-Alive
00:01:07.235: [Console Data] : Content-Length: 71
00:01:07.235: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":59,"version": "1.0"}
00:01:07.266: [Console Data] : 001-00:07:09.441 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent
00:01:07.266: [Console Data] : HTTP/1.1 403 Forbidden
00:01:07.266: [Console Data] : Content-Type: application/json
00:01:07.266: [Console Data] : Connection: keep-alive
00:01:07.266: [Console Data] : Content-Length: 168
00:01:07.266: [Console Data] : --------
00:01:07.266: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":59}
00:01:07.532: [Console Data] : 001-00:07:09.708 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport
00:01:07.547: [Console Data] : 001-00:07:09.717 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio
00:01:07.547: [Console Data] : Headers:
00:01:07.547: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:07.547: [Console Data] : Content-Type: application/json
00:01:07.547: [Console Data] : Connection: Keep-Alive
00:01:07.547: [Console Data] : Content-Length: 70
00:01:07.547: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":60,"version": "1.0"}
00:01:07.594: [Console Data] : 001-00:07:09.745 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio
00:01:07.594: [Console Data] : HTTP/1.1 200 OK
00:01:07.594: [Console Data] : Content-Type: application/json
00:01:07.594: [Console Data] : Connection: keep-alive
00:01:07.594: [Console Data] : Content-Length: 98
00:01:07.594: [Console Data] : --------
00:01:07.594: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":60}
00:01:07.672: [Console Data] : 001-00:07:09.838 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetEnergyStar' to transport
00:01:07.672: [Console Data] : 001-00:07:09.847 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system
00:01:07.672: [Console Data] : Headers:
00:01:07.672: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:07.672: [Console Data] : Content-Type: application/json
00:01:07.672: [Console Data] : Connection: Keep-Alive
00:01:07.672: [Console Data] : Content-Length: 68
00:01:07.672: [Console Data] : Content:{"method":"getPowerSavingMode","params":[],"id":61,"version": "1.0"}
00:01:07.703: [Console Data] : 001-00:07:09.872 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system
00:01:07.703: [Console Data] : HTTP/1.1 200 OK
00:01:07.703: [Console Data] : Content-Type: application/json
00:01:07.703: [Console Data] : Connection: keep-alive
00:01:07.703: [Console Data] : Content-Length: 35
00:01:07.703: [Console Data] : --------
00:01:07.703: [Console Data] : {"result":[{"mode":"off"}],"id":61}
00:01:11.172: [Console Data] : 001-00:07:13.345 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport
00:01:11.188: [Console Data] : 001-00:07:13.354 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system
00:01:11.188: [Console Data] : Headers:
00:01:11.188: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:11.188: [Console Data] : Content-Type: application/json
00:01:11.188: [Console Data] : Connection: Keep-Alive
00:01:11.188: [Console Data] : Content-Length: 64
00:01:11.188: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":62,"version": "1.0"}
00:01:11.219: [Console Data] : 001-00:07:13.385 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system
00:01:11.219: [Console Data] : HTTP/1.1 200 OK
00:01:11.219: [Console Data] : Content-Type: application/json
00:01:11.219: [Console Data] : Connection: keep-alive
00:01:11.219: [Console Data] : Content-Length: 40
00:01:11.219: [Console Data] : --------
00:01:11.219: [Console Data] : {"result":[{"status":"active"}],"id":62}
00:01:11.313: [Console Data] : 001-00:07:13.476 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport
00:01:11.313: [Console Data] : 001-00:07:13.485 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent
00:01:11.313: [Console Data] : Headers:
00:01:11.313: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:11.313: [Console Data] : Content-Type: application/json
00:01:11.313: [Console Data] : Connection: Keep-Alive
00:01:11.313: [Console Data] : Content-Length: 71
00:01:11.313: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":63,"version": "1.0"}
00:01:11.344: [Console Data] : 001-00:07:13.511 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent
00:01:11.344: [Console Data] : HTTP/1.1 403 Forbidden
00:01:11.344: [Console Data] : Content-Type: application/json
00:01:11.344: [Console Data] : Connection: keep-alive
00:01:11.344: [Console Data] : Content-Length: 168
00:01:11.344: [Console Data] : --------
00:01:11.344: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":63}
00:01:11.594: [Console Data] : 001-00:07:13.771 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport
00:01:11.610: [Console Data] : 001-00:07:13.780 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio
00:01:11.610: [Console Data] : Headers:
00:01:11.610: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:11.610: [Console Data] : Content-Type: application/json
00:01:11.610: [Console Data] : Connection: Keep-Alive
00:01:11.610: [Console Data] : Content-Length: 70
00:01:11.610: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":64,"version": "1.0"}
00:01:11.672: [Console Data] : 001-00:07:13.812 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio
00:01:11.672: [Console Data] : HTTP/1.1 200 OK
00:01:11.672: [Console Data] : Content-Type: application/json
00:01:11.672: [Console Data] : Connection: keep-alive
00:01:11.672: [Console Data] : Content-Length: 98
00:01:11.672: [Console Data] : --------
00:01:11.672: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":64}
00:01:15.250: [Console Data] : 001-00:07:17.415 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport
00:01:15.250: [Console Data] : 001-00:07:17.424 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system
00:01:15.250: [Console Data] : Headers:
00:01:15.250: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:15.250: [Console Data] : Content-Type: application/json
00:01:15.250: [Console Data] : Connection: Keep-Alive
00:01:15.250: [Console Data] : Content-Length: 64
00:01:15.250: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":65,"version": "1.0"}
00:01:15.282: [Console Data] : 001-00:07:17.451 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system
00:01:15.282: [Console Data] : HTTP/1.1 200 OK
00:01:15.282: [Console Data] : Content-Type: application/json
00:01:15.282: [Console Data] : Connection: keep-alive
00:01:15.282: [Console Data] : Content-Length: 40
00:01:15.282: [Console Data] : --------
00:01:15.282: [Console Data] : {"result":[{"status":"active"}],"id":65}
00:01:15.375: [Console Data] : 001-00:07:17.544 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport
00:01:15.391: [Console Data] : 001-00:07:17.553 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent
00:01:15.391: [Console Data] : Headers:
00:01:15.391: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:15.391: [Console Data] : Content-Type: application/json
00:01:15.391: [Console Data] : Connection: Keep-Alive
00:01:15.391: [Console Data] : Content-Length: 71
00:01:15.391: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":66,"version": "1.0"}
00:01:15.407: [Console Data] : 001-00:07:17.578 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent
00:01:15.407: [Console Data] : HTTP/1.1 403 Forbidden
00:01:15.407: [Console Data] : Content-Type: application/json
00:01:15.407: [Console Data] : Connection: keep-alive
00:01:15.407: [Console Data] : Content-Length: 168
00:01:15.407: [Console Data] : --------
00:01:15.407: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":66}
00:01:15.672: [Console Data] : 001-00:07:17.834 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport
00:01:15.672: [Console Data] : 001-00:07:17.843 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio
00:01:15.672: [Console Data] : Headers:
00:01:15.672: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:15.672: [Console Data] : Content-Type: application/json
00:01:15.672: [Console Data] : Connection: Keep-Alive
00:01:15.672: [Console Data] : Content-Length: 70
00:01:15.672: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":67,"version": "1.0"}
00:01:15.703: [Console Data] : 001-00:07:17.874 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio
00:01:15.703: [Console Data] : HTTP/1.1 200 OK
00:01:15.703: [Console Data] : Content-Type: application/json
00:01:15.703: [Console Data] : Connection: keep-alive
00:01:15.703: [Console Data] : Content-Length: 98
00:01:15.703: [Console Data] : --------
00:01:15.703: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":67}
00:01:15.797: [Console Data] : 001-00:07:17.964 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetEnergyStar' to transport
00:01:15.797: [Console Data] : 001-00:07:17.973 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system
00:01:15.797: [Console Data] : Headers:
00:01:15.797: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:15.797: [Console Data] : Content-Type: application/json
00:01:15.797: [Console Data] : Connection: Keep-Alive
00:01:15.797: [Console Data] : Content-Length: 68
00:01:15.797: [Console Data] : Content:{"method":"getPowerSavingMode","params":[],"id":68,"version": "1.0"}
00:01:15.828: [Console Data] : 001-00:07:18.002 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system
00:01:15.828: [Console Data] : HTTP/1.1 200 OK
00:01:15.828: [Console Data] : Content-Type: application/json
00:01:15.828: [Console Data] : Connection: keep-alive
00:01:15.828: [Console Data] : Content-Length: 35
00:01:15.828: [Console Data] : --------
00:01:15.828: [Console Data] : {"result":[{"mode":"off"}],"id":68}
00:01:19.297: [Console Data] : 001-00:07:21.470 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport
00:01:19.313: [Console Data] : 001-00:07:21.479 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system
00:01:19.313: [Console Data] : Headers:
00:01:19.313: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:19.313: [Console Data] : Content-Type: application/json
00:01:19.313: [Console Data] : Connection: Keep-Alive
00:01:19.313: [Console Data] : Content-Length: 64
00:01:19.313: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":69,"version": "1.0"}
00:01:19.344: [Console Data] : 001-00:07:21.505 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system
00:01:19.344: [Console Data] : HTTP/1.1 200 OK
00:01:19.344: [Console Data] : Content-Type: application/json
00:01:19.344: [Console Data] : Connection: keep-alive
00:01:19.344: [Console Data] : Content-Length: 40
00:01:19.344: [Console Data] : --------
00:01:19.344: [Console Data] : {"result":[{"status":"active"}],"id":69}
00:01:19.438: [Console Data] : 001-00:07:21.599 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport
00:01:19.438: [Console Data] : 001-00:07:21.610 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent
00:01:19.438: [Console Data] : Headers:
00:01:19.438: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:19.438: [Console Data] : Content-Type: application/json
00:01:19.438: [Console Data] : Connection: Keep-Alive
00:01:19.438: [Console Data] : Content-Length: 71
00:01:19.438: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":70,"version": "1.0"}
00:01:19.485: [Console Data] : 001-00:07:21.643 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent
00:01:19.485: [Console Data] : HTTP/1.1 403 Forbidden
00:01:19.485: [Console Data] : Content-Type: application/json
00:01:19.485: [Console Data] : Connection: keep-alive
00:01:19.485: [Console Data] : Content-Length: 168
00:01:19.485: [Console Data] : --------
00:01:19.485: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":70}
00:01:19.735: [Console Data] : 001-00:07:21.907 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport
00:01:19.750: [Console Data] : 001-00:07:21.915 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio
00:01:19.750: [Console Data] : Headers:
00:01:19.750: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:19.750: [Console Data] : Content-Type: application/json
00:01:19.750: [Console Data] : Connection: Keep-Alive
00:01:19.750: [Console Data] : Content-Length: 70
00:01:19.750: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":71,"version": "1.0"}
00:01:19.813: [Console Data] : 001-00:07:21.944 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio
00:01:19.813: [Console Data] : HTTP/1.1 200 OK
00:01:19.813: [Console Data] : Content-Type: application/json
00:01:19.813: [Console Data] : Connection: keep-alive
00:01:19.813: [Console Data] : Content-Length: 98
00:01:19.813: [Console Data] : --------
00:01:19.813: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":71}
00:01:23.360: [Console Data] : 001-00:07:25.526 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport
00:01:23.360: [Console Data] : 001-00:07:25.536 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system
00:01:23.360: [Console Data] : Headers:
00:01:23.360: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:23.360: [Console Data] : Content-Type: application/json
00:01:23.360: [Console Data] : Connection: Keep-Alive
00:01:23.360: [Console Data] : Content-Length: 64
00:01:23.360: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":72,"version": "1.0"}
00:01:23.391: [Console Data] : 001-00:07:25.561 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system
00:01:23.391: [Console Data] : HTTP/1.1 200 OK
00:01:23.391: [Console Data] : Content-Type: application/json
00:01:23.391: [Console Data] : Connection: keep-alive
00:01:23.391: [Console Data] : Content-Length: 40
00:01:23.391: [Console Data] : --------
00:01:23.391: [Console Data] : {"result":[{"status":"active"}],"id":72}
00:01:23.500: [Console Data] : 001-00:07:25.655 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport
00:01:23.516: [Console Data] : 001-00:07:25.664 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent
00:01:23.516: [Console Data] : Headers:
00:01:23.516: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:23.516: [Console Data] : Content-Type: application/json
00:01:23.516: [Console Data] : Connection: Keep-Alive
00:01:23.516: [Console Data] : Content-Length: 71
00:01:23.516: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":73,"version": "1.0"}
00:01:23.516: [Console Data] : 001-00:07:25.687 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent
00:01:23.516: [Console Data] : HTTP/1.1 403 Forbidden
00:01:23.516: [Console Data] : Content-Type: application/json
00:01:23.516: [Console Data] : Connection: keep-alive
00:01:23.516: [Console Data] : Content-Length: 168
00:01:23.516: [Console Data] : --------
00:01:23.516: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":73}
00:01:23.813: [Console Data] : 001-00:07:25.987 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport
00:01:23.828: [Console Data] : 001-00:07:25.997 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio
00:01:23.828: [Console Data] : Headers:
00:01:23.828: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:23.828: [Console Data] : Content-Type: application/json
00:01:23.828: [Console Data] : Connection: Keep-Alive
00:01:23.828: [Console Data] : Content-Length: 70
00:01:23.828: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":74,"version": "1.0"}
00:01:23.875: [Console Data] : 001-00:07:26.034 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio
00:01:23.875: [Console Data] : HTTP/1.1 200 OK
00:01:23.875: [Console Data] : Content-Type: application/json
00:01:23.875: [Console Data] : Connection: keep-alive
00:01:23.875: [Console Data] : Content-Length: 98
00:01:23.875: [Console Data] : --------
00:01:23.875: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":74}
00:01:23.953: [Console Data] : 001-00:07:26.126 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetEnergyStar' to transport
00:01:23.969: [Console Data] : 001-00:07:26.134 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system
00:01:23.969: [Console Data] : Headers:
00:01:23.969: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:23.969: [Console Data] : Content-Type: application/json
00:01:23.969: [Console Data] : Connection: Keep-Alive
00:01:23.969: [Console Data] : Content-Length: 68
00:01:23.969: [Console Data] : Content:{"method":"getPowerSavingMode","params":[],"id":75,"version": "1.0"}
00:01:24.000: [Console Data] : 001-00:07:26.161 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system
00:01:24.000: [Console Data] : HTTP/1.1 200 OK
00:01:24.000: [Console Data] : Content-Type: application/json
00:01:24.000: [Console Data] : Connection: close
00:01:24.000: [Console Data] : Content-Length: 35
00:01:24.000: [Console Data] : --------
00:01:24.000: [Console Data] : {"result":[{"mode":"off"}],"id":75}
00:01:27.407: [Console Data] : 001-00:07:29.580 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport
00:01:27.422: [Console Data] : 001-00:07:29.591 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system
00:01:27.422: [Console Data] : Headers:
00:01:27.422: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:27.422: [Console Data] : Content-Type: application/json
00:01:27.422: [Console Data] : Connection: Keep-Alive
00:01:27.422: [Console Data] : Content-Length: 64
00:01:27.422: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":76,"version": "1.0"}
00:01:27.453: [Console Data] : 001-00:07:29.629 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system
00:01:27.453: [Console Data] : HTTP/1.1 200 OK
00:01:27.453: [Console Data] : Content-Type: application/json
00:01:27.453: [Console Data] : Connection: keep-alive
00:01:27.453: [Console Data] : Content-Length: 40
00:01:27.453: [Console Data] : --------
00:01:27.453: [Console Data] : {"result":[{"status":"active"}],"id":76}
00:01:27.547: [Console Data] : 001-00:07:29.718 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport
00:01:27.563: [Console Data] : 001-00:07:29.726 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent
00:01:27.563: [Console Data] : Headers:
00:01:27.563: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:27.563: [Console Data] : Content-Type: application/json
00:01:27.563: [Console Data] : Connection: Keep-Alive
00:01:27.563: [Console Data] : Content-Length: 71
00:01:27.563: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":77,"version": "1.0"}
00:01:27.578: [Console Data] : 001-00:07:29.753 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent
00:01:27.578: [Console Data] : HTTP/1.1 403 Forbidden
00:01:27.578: [Console Data] : Content-Type: application/json
00:01:27.578: [Console Data] : Connection: keep-alive
00:01:27.578: [Console Data] : Content-Length: 168
00:01:27.578: [Console Data] : --------
00:01:27.578: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":77}
00:01:27.891: [Console Data] : 001-00:07:30.059 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport
00:01:27.907: [Console Data] : 001-00:07:30.067 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio
00:01:27.907: [Console Data] : Headers:
00:01:27.907: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:27.907: [Console Data] : Content-Type: application/json
00:01:27.907: [Console Data] : Connection: Keep-Alive
00:01:27.907: [Console Data] : Content-Length: 70
00:01:27.907: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":78,"version": "1.0"}
00:01:27.922: [Console Data] : 001-00:07:30.098 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio
00:01:27.922: [Console Data] : HTTP/1.1 200 OK
00:01:27.922: [Console Data] : Content-Type: application/json
00:01:27.922: [Console Data] : Connection: keep-alive
00:01:27.922: [Console Data] : Content-Length: 98
00:01:27.922: [Console Data] : --------
00:01:27.922: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":78}
00:01:31.485: [Console Data] : 001-00:07:33.650 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport
00:01:31.485: [Console Data] : 001-00:07:33.659 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system
00:01:31.485: [Console Data] : Headers:
00:01:31.485: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:31.485: [Console Data] : Content-Type: application/json
00:01:31.485: [Console Data] : Connection: Keep-Alive
00:01:31.485: [Console Data] : Content-Length: 64
00:01:31.485: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":79,"version": "1.0"}
00:01:31.516: [Console Data] : 001-00:07:33.686 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system
00:01:31.516: [Console Data] : HTTP/1.1 200 OK
00:01:31.516: [Console Data] : Content-Type: application/json
00:01:31.516: [Console Data] : Connection: keep-alive
00:01:31.516: [Console Data] : Content-Length: 40
00:01:31.516: [Console Data] : --------
00:01:31.516: [Console Data] : {"result":[{"status":"active"}],"id":79}
00:01:31.610: [Console Data] : 001-00:07:33.779 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport
00:01:31.625: [Console Data] : 001-00:07:33.790 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent
00:01:31.625: [Console Data] : Headers:
00:01:31.625: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:31.625: [Console Data] : Content-Type: application/json
00:01:31.625: [Console Data] : Connection: Keep-Alive
00:01:31.625: [Console Data] : Content-Length: 71
00:01:31.625: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":80,"version": "1.0"}
00:01:31.657: [Console Data] : 001-00:07:33.824 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent
00:01:31.657: [Console Data] : HTTP/1.1 403 Forbidden
00:01:31.657: [Console Data] : Content-Type: application/json
00:01:31.657: [Console Data] : Connection: keep-alive
00:01:31.657: [Console Data] : Content-Length: 168
00:01:31.657: [Console Data] : --------
00:01:31.657: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":80}
00:01:31.953: [Console Data] : 001-00:07:34.121 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport
00:01:31.969: [Console Data] : 001-00:07:34.132 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio
00:01:31.969: [Console Data] : Headers:
00:01:31.969: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:31.969: [Console Data] : Content-Type: application/json
00:01:31.969: [Console Data] : Connection: Keep-Alive
00:01:31.969: [Console Data] : Content-Length: 70
00:01:31.969: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":81,"version": "1.0"}
00:01:32.000: [Console Data] : 001-00:07:34.172 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio
00:01:32.000: [Console Data] : HTTP/1.1 200 OK
00:01:32.000: [Console Data] : Content-Type: application/json
00:01:32.000: [Console Data] : Connection: keep-alive
00:01:32.000: [Console Data] : Content-Length: 98
00:01:32.000: [Console Data] : --------
00:01:32.000: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":81}
00:01:32.078: [Console Data] : 001-00:07:34.251 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetEnergyStar' to transport
00:01:32.094: [Console Data] : 001-00:07:34.260 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system
00:01:32.094: [Console Data] : Headers:
00:01:32.094: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:32.094: [Console Data] : Content-Type: application/json
00:01:32.094: [Console Data] : Connection: Keep-Alive
00:01:32.094: [Console Data] : Content-Length: 68
00:01:32.094: [Console Data] : Content:{"method":"getPowerSavingMode","params":[],"id":82,"version": "1.0"}
00:01:32.125: [Console Data] : 001-00:07:34.289 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system
00:01:32.125: [Console Data] : HTTP/1.1 200 OK
00:01:32.125: [Console Data] : Content-Type: application/json
00:01:32.125: [Console Data] : Connection: keep-alive
00:01:32.125: [Console Data] : Content-Length: 35
00:01:32.125: [Console Data] : --------
00:01:32.125: [Console Data] : {"result":[{"mode":"off"}],"id":82}
00:01:35.532: [Console Data] : 001-00:07:37.707 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport
00:01:35.547: [Console Data] : 001-00:07:37.716 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system
00:01:35.547: [Console Data] : Headers:
00:01:35.547: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:35.547: [Console Data] : Content-Type: application/json
00:01:35.547: [Console Data] : Connection: Keep-Alive
00:01:35.547: [Console Data] : Content-Length: 64
00:01:35.547: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":83,"version": "1.0"}
00:01:35.578: [Console Data] : 001-00:07:37.748 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system
00:01:35.578: [Console Data] : HTTP/1.1 200 OK
00:01:35.578: [Console Data] : Content-Type: application/json
00:01:35.578: [Console Data] : Connection: keep-alive
00:01:35.578: [Console Data] : Content-Length: 40
00:01:35.578: [Console Data] : --------
00:01:35.578: [Console Data] : {"result":[{"status":"active"}],"id":83}
00:01:35.672: [Console Data] : 001-00:07:37.836 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport
00:01:35.672: [Console Data] : 001-00:07:37.844 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent
00:01:35.672: [Console Data] : Headers:
00:01:35.672: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:35.672: [Console Data] : Content-Type: application/json
00:01:35.672: [Console Data] : Connection: Keep-Alive
00:01:35.672: [Console Data] : Content-Length: 71
00:01:35.672: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":84,"version": "1.0"}
00:01:35.703: [Console Data] : 001-00:07:37.873 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent
00:01:35.703: [Console Data] : HTTP/1.1 403 Forbidden
00:01:35.703: [Console Data] : Content-Type: application/json
00:01:35.703: [Console Data] : Connection: keep-alive
00:01:35.703: [Console Data] : Content-Length: 168
00:01:35.703: [Console Data] : --------
00:01:35.703: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":84}
00:01:36.016: [Console Data] : 001-00:07:38.194 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport
00:01:36.032: [Console Data] : 001-00:07:38.202 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio
00:01:36.032: [Console Data] : Headers:
00:01:36.032: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:36.032: [Console Data] : Content-Type: application/json
00:01:36.032: [Console Data] : Connection: Keep-Alive
00:01:36.032: [Console Data] : Content-Length: 70
00:01:36.032: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":85,"version": "1.0"}
00:01:36.094: [Console Data] : 001-00:07:38.261 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio
00:01:36.094: [Console Data] : HTTP/1.1 200 OK
00:01:36.094: [Console Data] : Content-Type: application/json
00:01:36.094: [Console Data] : Connection: keep-alive
00:01:36.094: [Console Data] : Content-Length: 98
00:01:36.094: [Console Data] : --------
00:01:36.094: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":85}
00:01:39.610: [Console Data] : 001-00:07:41.773 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport
00:01:39.610: [Console Data] : 001-00:07:41.782 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system
00:01:39.610: [Console Data] : Headers:
00:01:39.610: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:39.610: [Console Data] : Content-Type: application/json
00:01:39.610: [Console Data] : Connection: Keep-Alive
00:01:39.610: [Console Data] : Content-Length: 64
00:01:39.610: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":86,"version": "1.0"}
00:01:39.657: [Console Data] : 001-00:07:41.819 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system
00:01:39.657: [Console Data] : HTTP/1.1 200 OK
00:01:39.657: [Console Data] : Content-Type: application/json
00:01:39.657: [Console Data] : Connection: keep-alive
00:01:39.657: [Console Data] : Content-Length: 40
00:01:39.657: [Console Data] : --------
00:01:39.657: [Console Data] : {"result":[{"status":"active"}],"id":86}
00:01:39.735: [Console Data] : 001-00:07:41.910 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport
00:01:39.750: [Console Data] : 001-00:07:41.919 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent
00:01:39.750: [Console Data] : Headers:
00:01:39.750: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:39.750: [Console Data] : Content-Type: application/json
00:01:39.750: [Console Data] : Connection: Keep-Alive
00:01:39.750: [Console Data] : Content-Length: 71
00:01:39.750: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":87,"version": "1.0"}
00:01:39.782: [Console Data] : 001-00:07:41.947 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent
00:01:39.782: [Console Data] : HTTP/1.1 403 Forbidden
00:01:39.782: [Console Data] : Content-Type: application/json
00:01:39.782: [Console Data] : Connection: keep-alive
00:01:39.782: [Console Data] : Content-Length: 168
00:01:39.782: [Console Data] : --------
00:01:39.782: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":87}
00:01:40.110: [Console Data] : 001-00:07:42.285 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport
00:01:40.125: [Console Data] : 001-00:07:42.302 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio
00:01:40.125: [Console Data] : Headers:
00:01:40.125: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:40.125: [Console Data] : Content-Type: application/json
00:01:40.125: [Console Data] : Connection: Keep-Alive
00:01:40.125: [Console Data] : Content-Length: 70
00:01:40.125: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":88,"version": "1.0"}
00:01:40.172: [Console Data] : 001-00:07:42.332 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio
00:01:40.172: [Console Data] : HTTP/1.1 200 OK
00:01:40.172: [Console Data] : Content-Type: application/json
00:01:40.172: [Console Data] : Connection: keep-alive
00:01:40.172: [Console Data] : Content-Length: 98
00:01:40.172: [Console Data] : --------
00:01:40.172: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":88}
00:01:40.250: [Console Data] : 001-00:07:42.422 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetEnergyStar' to transport
00:01:40.266: [Console Data] : 001-00:07:42.430 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system
00:01:40.266: [Console Data] : Headers:
00:01:40.266: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:40.266: [Console Data] : Content-Type: application/json
00:01:40.266: [Console Data] : Connection: Keep-Alive
00:01:40.266: [Console Data] : Content-Length: 68
00:01:40.266: [Console Data] : Content:{"method":"getPowerSavingMode","params":[],"id":89,"version": "1.0"}
00:01:40.297: [Console Data] : 001-00:07:42.459 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system
00:01:40.297: [Console Data] : HTTP/1.1 200 OK
00:01:40.297: [Console Data] : Content-Type: application/json
00:01:40.297: [Console Data] : Connection: keep-alive
00:01:40.297: [Console Data] : Content-Length: 35
00:01:40.297: [Console Data] : --------
00:01:40.297: [Console Data] : {"result":[{"mode":"off"}],"id":89}
00:01:43.672: [Console Data] : 001-00:07:45.839 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport
00:01:43.672: [Console Data] : 001-00:07:45.848 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system
00:01:43.672: [Console Data] : Headers:
00:01:43.672: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:43.672: [Console Data] : Content-Type: application/json
00:01:43.672: [Console Data] : Connection: Keep-Alive
00:01:43.672: [Console Data] : Content-Length: 64
00:01:43.672: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":90,"version": "1.0"}
00:01:43.719: [Console Data] : 001-00:07:45.880 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system
00:01:43.719: [Console Data] : HTTP/1.1 200 OK
00:01:43.719: [Console Data] : Content-Type: application/json
00:01:43.719: [Console Data] : Connection: keep-alive
00:01:43.719: [Console Data] : Content-Length: 40
00:01:43.719: [Console Data] : --------
00:01:43.719: [Console Data] : {"result":[{"status":"active"}],"id":90}
00:01:43.797: [Console Data] : 001-00:07:45.967 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport
00:01:43.813: [Console Data] : 001-00:07:45.976 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent
00:01:43.813: [Console Data] : Headers:
00:01:43.813: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:43.813: [Console Data] : Content-Type: application/json
00:01:43.813: [Console Data] : Connection: Keep-Alive
00:01:43.813: [Console Data] : Content-Length: 71
00:01:43.813: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":91,"version": "1.0"}
00:01:43.844: [Console Data] : 001-00:07:46.006 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent
00:01:43.844: [Console Data] : HTTP/1.1 403 Forbidden
00:01:43.844: [Console Data] : Content-Type: application/json
00:01:43.844: [Console Data] : Connection: keep-alive
00:01:43.844: [Console Data] : Content-Length: 168
00:01:43.844: [Console Data] : --------
00:01:43.844: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":91}
00:01:44.188: [Console Data] : 001-00:07:46.356 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport
00:01:44.188: [Console Data] : 001-00:07:46.364 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio
00:01:44.188: [Console Data] : Headers:
00:01:44.188: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:44.188: [Console Data] : Content-Type: application/json
00:01:44.188: [Console Data] : Connection: Keep-Alive
00:01:44.188: [Console Data] : Content-Length: 70
00:01:44.188: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":92,"version": "1.0"}
00:01:44.219: [Console Data] : 001-00:07:46.395 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio
00:01:44.219: [Console Data] : HTTP/1.1 200 OK
00:01:44.219: [Console Data] : Content-Type: application/json
00:01:44.219: [Console Data] : Connection: keep-alive
00:01:44.219: [Console Data] : Content-Length: 98
00:01:44.219: [Console Data] : --------
00:01:44.219: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":92}
00:01:47.735: [Console Data] : 001-00:07:49.901 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetPower' to transport
00:01:47.735: [Console Data] : 001-00:07:49.910 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system
00:01:47.735: [Console Data] : Headers:
00:01:47.735: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:47.735: [Console Data] : Content-Type: application/json
00:01:47.735: [Console Data] : Connection: Keep-Alive
00:01:47.735: [Console Data] : Content-Length: 64
00:01:47.735: [Console Data] : Content:{"method":"getPowerStatus","params":[],"id":93,"version": "1.0"}
00:01:47.766: [Console Data] : 001-00:07:49.939 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system
00:01:47.766: [Console Data] : HTTP/1.1 200 OK
00:01:47.766: [Console Data] : Content-Type: application/json
00:01:47.766: [Console Data] : Connection: keep-alive
00:01:47.766: [Console Data] : Content-Length: 40
00:01:47.766: [Console Data] : --------
00:01:47.766: [Console Data] : {"result":[{"status":"active"}],"id":93}
00:01:47.860: [Console Data] : 001-00:07:50.029 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVideoInput' to transport
00:01:47.875: [Console Data] : 001-00:07:50.040 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/avContent
00:01:47.875: [Console Data] : Headers:
00:01:47.875: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:47.875: [Console Data] : Content-Type: application/json
00:01:47.875: [Console Data] : Connection: Keep-Alive
00:01:47.875: [Console Data] : Content-Length: 71
00:01:47.875: [Console Data] : Content:{"method":"getPlayingContentInfo","params":[],"id":94,"version": "1.0"}
00:01:47.907: [Console Data] : 001-00:07:50.077 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/avContent
00:01:47.907: [Console Data] : HTTP/1.1 403 Forbidden
00:01:47.907: [Console Data] : Content-Type: application/json
00:01:47.907: [Console Data] : Connection: keep-alive
00:01:47.907: [Console Data] : Content-Length: 168
00:01:47.907: [Console Data] : --------
00:01:47.907: [Console Data] : {"auth_url":{"default":"http:\/\/10.110.250.30:80\/sony\/webauth\/auth_default","tv":"http:\/\/127.0.0.1:80\/sony\/webauth\/auth_tv"},"error":[403,"Forbidden"],"id":94}
00:01:48.250: [Console Data] : 001-00:07:50.418 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetVolume' to transport
00:01:48.250: [Console Data] : 001-00:07:50.427 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/audio
00:01:48.250: [Console Data] : Headers:
00:01:48.250: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:48.250: [Console Data] : Content-Type: application/json
00:01:48.250: [Console Data] : Connection: Keep-Alive
00:01:48.250: [Console Data] : Content-Length: 70
00:01:48.250: [Console Data] : Content:{"method":"getVolumeInformation","params":[],"id":95,"version": "1.0"}
00:01:48.297: [Console Data] : 001-00:07:50.461 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/audio
00:01:48.297: [Console Data] : HTTP/1.1 200 OK
00:01:48.297: [Console Data] : Content-Type: application/json
00:01:48.297: [Console Data] : Connection: keep-alive
00:01:48.297: [Console Data] : Content-Length: 98
00:01:48.297: [Console Data] : --------
00:01:48.297: [Console Data] : {"result":[[{"target":"speaker","volume":15,"mute":false,"maxVolume":100,"minVolume":0}]],"id":95}
00:01:48.375: [Console Data] : 001-00:07:50.548 ( 1) [Info? ?] CORD | Sony XBR Series Display : Sending command 'GetEnergyStar' to transport
00:01:48.391: [Console Data] : 001-00:07:50.564 ( 1) [Trace? ] TSPT | HttpTransport-TX? : Post http://10.110.250.30/sony/system
00:01:48.391: [Console Data] : Headers:
00:01:48.391: [Console Data] : X-Auth-PSK: F8:4E:17:25:79:14
00:01:48.391: [Console Data] : Content-Type: application/json
00:01:48.391: [Console Data] : Connection: Keep-Alive
00:01:48.391: [Console Data] : Content-Length: 68
00:01:48.391: [Console Data] : Content:{"method":"getPowerSavingMode","params":[],"id":96,"version": "1.0"}
00:01:48.422: [Console Data] : 001-00:07:50.595 ( 1) [Trace? ] TSPT | HttpTransport-RX? : From Url: http://10.110.250.30/sony/system
00:01:48.422: [Console Data] : HTTP/1.1 200 OK
00:01:48.422: [Console Data] : Content-Type: application/json
00:01:48.422: [Console Data] : Connection: keep-alive
00:01:48.422: [Console Data] : Content-Length: 35
00:01:48.422: [Console Data] : --------
00:01:48.422: [Console Data] : {"result":[{"mode":"off"}],"id":96}?


Re: NewTek Tricaster control with Crestron

 

this was in a serial I/o. ?I got nothing else. ?I don't think we had feedback. ?It was a "last second" add and I just slapped it together....


Re: Task Apps

 

Trello is a simple way to do something similar.? I just have to avoid the trap of too much time into organizing my todos and not enough time getting them done.? Hard to beat a paper todo list for the investment/reward ratio.


On Thu, Sep 1, 2022 at 3:35 AM Thorsten K?hler <thorsten.koehler@...> wrote:

Hi,

i use Jira. Not in a very sophisticated way, but pretty simple way (Kanban/team style). Just creating cards (todos) with a (short) description of the todo, then with updates over time. You just move these cards through different stages ¨C open, in progress, testing, done. (you can define your own stages if you prefer).

You can assign people from your team if you want to, but I also use it to track my own tasks.

You can do pretty sophisticated stuff with it, but i prefer to keep it simple.

?

Cheers,

Thorsten

?

Von: [email protected] <[email protected]> Im Auftrag von ckangis
Gesendet: Mittwoch, 31. August 2022 21:34
An: [email protected]
Betreff: [crestron] Task Apps

?

Hi All,
Other than Outlook, What task manager apps are people using and liking??? I.e. an App that allows you to document tasks and their piece-part do-list items...
TIA!


Toolbox - Failed to connect. Link may be broken error. #toolbox

 

Brand new Dell XPS with win 11.
So fresh install of all Crestron sw. Thankfully simpl/s+ compiles worked straight off the bat and generally all Crestron sw is working well.

One minor annoyance is I get the above error whenever I close a tool in Toolbox. Doesn't matter if the tool is connected to a device or not.

Nothing else appears broken. Just wandering if anyone else seeing this.

Cheers
s


Re: Task Apps

 

¿ªÔÆÌåÓý

Hi,

i use Jira. Not in a very sophisticated way, but pretty simple way (Kanban/team style). Just creating cards (todos) with a (short) description of the todo, then with updates over time. You just move these cards through different stages ¨C open, in progress, testing, done. (you can define your own stages if you prefer).

You can assign people from your team if you want to, but I also use it to track my own tasks.

You can do pretty sophisticated stuff with it, but i prefer to keep it simple.

?

Cheers,

Thorsten

?

Von: [email protected] <[email protected]> Im Auftrag von ckangis
Gesendet: Mittwoch, 31. August 2022 21:34
An: [email protected]
Betreff: [crestron] Task Apps

?

Hi All,
Other than Outlook, What task manager apps are people using and liking??? I.e. an App that allows you to document tasks and their piece-part do-list items...
TIA!


Re: WattBox WB-150-IPW-1B-2 and Crestron driver - Checking for power #simplwindows #crestron #poll

 

ckangis,
? ? I do have that module in SimplWindows right now and the Wattbox (it's controlling a fan right now as a test) is connected over WiFi. I have two buttons on my touch panel for off and on which both have feedback via an interlock. If I reboot my MC3 with the fan on, it stays on but I lose the feedback on the touch panel.

If I use the poll now signal in the module, how would check this and have the buttons show feedback on a reboot of the MC3 or touch panel?

Thanks dsmith


Re: Crosspoint ECCON Timing

 

¿ªÔÆÌåÓý

Ditto¡­ Though I usually use 5d because I have seen some odd behaviors specifically with some analog use cases if I make the timing too tight (3, or 4d would work¡­ but 5d is fast enough and works 100% of the time so I haven¡¯t really tried poking the bear)

?

--

Lincoln King-Cliby, CTS, DMC-E-4K/T/D
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Diamond)
ControlWorks Consulting, LLC
Direct: (+1)440.771.4807 | Cleveland: (+1)440.449.1100? | Boston: (+1)508.695.0188 | DC: (+1)202.381.9070? | Fax: (+1)440.449.1106
Crestron Services Provider | Biamp Authorized Independent Programmers | Extron Qualified Independent Programmer

?

From: [email protected] [mailto:[email protected]] On Behalf Of Phil Bridges
Sent: Wednesday, August 31, 2022 4:24 PM
To: [email protected]
Subject: Re: [crestron] Crosspoint ECCON Timing

?

I usually do a 1d sawpulse?based on the equipment ID - out is disconnect from control, out* is connect,?

?

On Wed, Aug 31, 2022 at 3:27 PM ckangis <chris@...> wrote:

Hi All,
I'm working on a new development project with crosspoints again and wanted to get others' opinions regarding disconnect/connect timings.
My basic worldview with regard to any XP subsystem, is to have one Control XP with its own ECCON that connects to one Equipment XP. when another device is needed, I disconnect from the first and connect to the second.
I.e. a Control XP is never connected to more than one Equipment XP at any one time (I know that there are other use-cases, but this is what is most modular and scalable in my mind...)

Over the years, I have used various timing between disconnect and reconnect processes (usually 2-4 logic waves).?
I would use LWP (1d) signals for triggers...and primarily 4-series processors and possibly VC-4. of course, I'll need to consider 3-series for the next year or two until the supply issues are worked thru...

Does anyone recommend a 1-logicWave transition between Disconnect? and re-connect, or is the consensus to use a few LWs for this??
TIA!


Re: NewTek Tricaster control with Crestron

 

Thanks Michael.?

Did you do anything else that might show if you received anything when a macros was executed? Anything else that you think might be useful to know?
I've never worked with the device and I'm just trying to gather as much as possible before I sit in front of it next week.


On Wed, Aug 31, 2022 at 7:47 AM Michael Block <michael@...> wrote:
This worked for me on a project a few years back.

TCP Port: 5951
<trigger name=\x22Macro-1\x22/>\r

Michael


Re: Crosspoint ECCON Timing

 

What Phil said


Re: Crosspoint ECCON Timing

 

I just use an AOS much like Phil uses the sawpulse.? This triggers on any change of the equipment ID. I believe I copied this logic right from the original Xpoint example program.


Re: Crosspoint ECCON Timing

 

I usually do a 1d sawpulse?based on the equipment ID - out is disconnect from control, out* is connect,?


On Wed, Aug 31, 2022 at 3:27 PM ckangis <chris@...> wrote:
Hi All,
I'm working on a new development project with crosspoints again and wanted to get others' opinions regarding disconnect/connect timings.
My basic worldview with regard to any XP subsystem, is to have one Control XP with its own ECCON that connects to one Equipment XP. when another device is needed, I disconnect from the first and connect to the second.
I.e. a Control XP is never connected to more than one Equipment XP at any one time (I know that there are other use-cases, but this is what is most modular and scalable in my mind...)

Over the years, I have used various timing between disconnect and reconnect processes (usually 2-4 logic waves).?
I would use LWP (1d) signals for triggers...and primarily 4-series processors and possibly VC-4. of course, I'll need to consider 3-series for the next year or two until the supply issues are worked thru...

Does anyone recommend a 1-logicWave transition between Disconnect? and re-connect, or is the consensus to use a few LWs for this??
TIA!


Re: Crosspoint ECCON Timing

 

Also, in reading in the Help file/Numeric Formats, it states that using '0d' as a time parameter, say in an AOS, will render a single logic wave (solution) pulse.
This begs the question, what does '1d' do in this situation?? still a single wave pulse?


Task Apps

 

Hi All,
Other than Outlook, What task manager apps are people using and liking??? I.e. an App that allows you to document tasks and their piece-part do-list items...
TIA!