Folks -?

I am using the Fusion SSI Help Message Module, and in the middle parameter section, it has a place to insert predetermined serial string messages. Does anyone know if/what syntax would be to fill the parameter section from outside the module dynamically?

I want to change the messages on the fly without recompiling and pushing.

Is there a prefix and suffix to use?

I appreciate any help you can provide.

AV_Programmer

HTTPS Get Request????????

?

Any help would be appreciated as I’m going around in circles and more confused than when I started….lol

Requirement:? https GET request to the Solar Edge Monitoring site to return Solar Panel Data

Assumptions:

1. SIMPL can not handle https request using SIO only http
2. API Key required

?

?

My initial thoughts were to use httpsUtilityv2.1? I have tried a number of times and either got nothing or error codes.???? I’ve confused myself as to what I did now and how I got what I got ??

?

Question:

1. Can I use the httpsUtility module to do this request
2. If so the Utility I believe has 3 data entries:?How should I enter the https GET request below within the utility?????????I have used Postman as you will see below and this works fine.

?

a.?????? url$

b.?????? headers$

c.?????? content$

?

3.?Any additional pointers as to where I can learn about how to send https requests in SIMPL / SIMPL+ would be appreciated.? ? ? This is very much a new area for me and trying hard to understand but lost at the moment.??

?

?

?

GET Request in Postman:

https://monitoringapi.solaredge.com/site/[Insrt Site ID]/currentPowerFlow?api_key=[Insert API Key]

?

HTTP View after send

GET /site/[insert Site ID]/currentPowerFlow?api_key=[Insert Key]HTTP/1.1

Host: monitoringapi.solaredge.com

Cookie: JSESSIONID=A079CB3BCD65A2BED64BD48E7DC56A3A

?

Data Returned (Raw)

{"siteCurrentPowerFlow":{"updateRefreshRate":3,"unit":"kW","connections":[{"from":"PV","to":"Load"},{"from":"GRID","to":"Load"},{"from":"PV","to":"Storage"}],"GRID":{"status":"Active","currentPower":0.03},"LOAD":{"status":"Active","currentPower":0.96},"PV":{"status":"Active","currentPower":1.53},"STORAGE":{"status":"Charging","currentPower":0.6,"chargeLevel":36,"critical":false}}}

开云体育

I may have 1 available that was opened thrown into a rack and the project changed to a different piece of gear. ?Will know more later today if you want to email me directly.

I haven't been back to that site, and I think the dealer and homeowner have abandoned alarm integration for now.

Crestron has put the driver back on the CCD site, but I don't have any upcoming projects that will need it, and don't have a panel available to test. When I reviewed the dat file, it didn't seem to support keypad emulation or discrete zone status. Hopefully I missed something :-)

Indeed, I mean, for me as a programmer I couldn't care less about how many interconnects they have to do (lol).? For the price point of NAX to also include an Autonomic it almost becomes easier to just use a better dummy audio distribution solution in some cases, which we do.? Surprisingly, I have found the Autonomic audio distribution to be pretty rock solid for analog systems!? But thats not really on topic.

Have a need--please let me know $ maybe more than 1?

I also have worked extensively with this product and have a fairly good amount of "practical" information that I have extracted in short form from the documentation. I have written at least a couple of useful modules that provide a number of parameter based presets of various colors as well as dynamically editable presets of various colors. I can post some details if you are still in need.

Never digged too deep for this bug, I just put a buffer on all inputs within this module, and enable the buffer by the initial input from the core module, error gone.

Thanks for all the replies chaps,

The main AV CP3 sits on our service VLAN-4
The 5 Sonos players are on the user VLAN-3 and these are handled by a second CP3 on the user VLAN.

I've changed my logic slightly and now start the stream based on the following:
* Update status - sets an IL
* Valid Multicast address
* NAX is online (using offline manager device extender for each of the NAX units)
* Sonos CP3 online

So far I have not implemented setting the port.

The above hoop jumping seems to be favorable, however I'll hold off judgement until I've tested this some more.

@Eric Luckard
The IT guys have combed over the network and they are satisfied that it is up to task.
The management ports on the NAX's are on the user VLAN. The content ports are on a dedicated NVX/NAX VLAN.
No issues with NVX.

There are a total of 6 x DM-NAX-8ZSA on this site.
The 5 Sonos units are in the head end connected to the 2 DM-NAX-8ZSA that I mentioned previously and these need to be streamed to all the remote DM-NAX-8ZSA's.

Hi Geoffrey,?

Are you still selling licenses for your IR tool? I tried reaching out on the email on your website but I got a bounce back.?

开云体育

Hi Slip

开云体育

Tony, What did you figure out? Any keypad emulation or zone feedback?

If you can figure out how to convert the sn# to a TSID you could use setppnbycresnetid

In the files section. Chip has a Day of the week module that is all in simpl. I have used it a few times and it works well.

What TV?

I have also stopped using the built in streaming. I didn't like how if someone was streaming something on stream 1 then zone 1 decided to airplay it would takeover that stream.

We have used Cisco CBS, Netgear 4300 & 4250's with our NAX's and I cant say I have had any issues with source sharing. On most of my projects access AES67 sources from both NVX's and other NAX's. I am wondering if it isn't something with your network.

Anyone can guide me to how to control an Andriod TV via IP (like using a remote control) through SIMPL??

I'm having similar error right now with two CP4N, loaded with different program.

I've been investigating it with Crestron Support for 2-month, the error only happened 3-time, all in same time slot - 10 min after program restart, while we have restarted program like million of times, it only happened 3-time. Required reboot of CP4N when it happened.